You shouldn’t have ya legs under like that brother. No matter what. God Bless. Thank you

So my mavic camera looks up n down that's it, do i only need a new reabon

An easy way with almost any saw is that the arbor bolt turns the same way the blade cuts to loosen it

Get a Diablo Steel Demon blade, much faster no sparks.. they're a bit pricey but worth it. With that being said i have an old Makita miter saw that's going to be for metal and i was cheap and got the grinding wheel BUT i have the steel demon setup in a circular saw and it cuts nice

The pilot jet is plugged

Are they still holding up heard a lot of feed back about mag tech

Absolutely gamechaning stuff!

If you plan to build a dual monitor setup with old Thunderbolt displays, you should take into account that the devices almost all have different brightness levels due to their age. Over the last few years I've had about 7 Thunderbolt displays and the brightness has been between 3,900 (almost yellow image) and 5,900 (pretty good white) lux. Apparently the displays burn out over the years depending on how heavily they're used. I measured 6,500 lux during the iMac 5K DIY monitor conversion.

Mine start at idle but went i give gaz die dont no what to do

As a single mom trying to do some updating home repairs with little knowledge… THANK YOU!!!

There worst video 😂

No grease where the shoes touch the backing plate? You should wire wheel the hub center too.

Your video sucks

I have 2 Apple Monitor A1407 (with thunderbolt icon) and A1316 (with display/tv icon look alike) Apple model A1407 cannot connect at all with adapters.. other model Apple A1316 can display without any issue.. with HDMI to DP adapter to Windows 11 Pro. any1 here successfully connect A1407 monitor to HDMI???

Your fuel air screw will probably be between 1 1/2 to 2 1/2 turns out. Check the factory specs and start from there. It’s not the cdi

Awesome video man keep up work an switch bulbs are used

Thanks alot 🎉🎉🎉

I've been doing Drum Brakes for 40 years. Unless you live in a no snow State, the Drums will never slide off as shown. Get grade 5 8mm bolts to drive the drum off. That's the purpose of the 2 threaded holes in the drum. Although Honda reduced how many Springs are used to hold the Shoes, you cannot use any of the Brake tools that have worked in the past. The single, large top Spring is a very toughy. Even with the Adjuster turned all the way in, and brake shoes and e-brake set correctly in the Adjuster Fork, it is tough tough tough. No reason that springs needs to be that stiff. Because of the small brake shoes, all the hardware hides behind the axle hub. Even basic hand tools have limited room. For many years I wondered why they just don't use a simple Snap Ring for that e-brake clip.

Thank you! Saw so many videos where they already had those settings off and only copied and pasted models on top of one another thank you so much!

Hello! I have a apple thunderbolt display 2011 and I would like to connect it to windows desktop PC ! I try so hard to do it but I have not been able to get a signal from the computer's graphics card to the Mac display! Please help!!

You're off to a bad start. I have one. You don't floor your car all day. Diesels want to run on a fraction of their output. An alternator or a big alternator. For AC, use a pure sine wave inverter after 12 volts, DC. Funny fluids is how you shorten it's life. I want mine to last thousands of hours. Don't copy failure. Project Farm broke his.

thanks so much for this!!

Can you get a Miniport to a HDMI and plug the mac monitor into my PC?

Can the mac mini or mac studio with M2 be connected to the apple thunderbolt display or is there incompatibility? Do I necessarily have to use the Thunderbolt 3 to Thunderbolt 2 adapter? Or should we proceed another way? Should I use the same display cable or another one? Or is it possible with the mac M1 but not with the M2?

Brilliant! Even if it will hit I feel like most of my tall parts would be fine getting knocked over, but also sequencing them so the order moves the gantry away from previous prints will also save lots of time. Thanks for sharing!

Does anyone here had a trouble when PC does not recognise camera and microphone? Do you use any specific drivers? Thanks in advance

This is increibly helpful thanks so much!

trimakasih tutorialnya.. Semoga sehat dan berkah

Hi I'm looking to connect a 2011 Apple A1407 monitor with aThunderbolt 2 output to my 2018 Windows Dell G5 15 laptop. Said laptop have the followings ports: 1)HDMI port. 2) Mini display port. 3) USB 3.1 Gen 2 Type-C port. Can I use the adapter that you recommended?

You don't need to use that vise grip to stop the shoe from expanding. The slave cylinder doesn't have enough pressure to pop the piston out...as I've never experienced that happning in over 50 yrs😂 It might if someone got in the car and accidently pressed the brake pedal...but what are chances of that?🙄

Hi thanks for you video, please need a advise, i have a 27 inch thunderbolt screen i think is the same as yours, wan to connect it ta a alienware laptop which has a mini display port which looks as the thunderbolt. Which plug do i have to buy ??

Thanks for posting this. I was wondering if they will work with Ubuntu but it seems like it is hit or miss depending on the computer hardware and the appropriate adapters. Good for you for not giving up when the Apple adapter did not work.

what size is the adapter? 5/8? is that just a regular washer?

Apple cinema A 1407 ? thanks bro

can use for apple cinema thunder bolt A1407 ? Thanks you!!

IS this apple cinema or apple thunderbolt display?

This is the 3rd video I have watched on changing the brake shoes and I am now definitely paying my mechanic to do it,

Can you use Apple thunderbolt 3 to 2 to connect with Windows PC And How to Adjust Brightness on Your Screen Hope you feedback Thanks you

It really cool video So i can other use other main board for using apple thunderbolt display? Thanks

Igual paso con mi colorado 2007 le cambié el termostato y subió la aguja más de la mitad creía que era porque no era el original le pose el original y quedó igual 😬😬😬😬

still can’t connect to pc 😢

Great video!!

Hi, I have a question I recently git an i mac A1407 which have the thunderbolt connection I tried multiple adapters to hooked to my dell PC but no luck and when I asked my brother he said he has the P400 and gave it to me I tried connecting the i mac directly to the thunderbolt but didn't work so I tried the thunderbolt to DVI converter with a different screen and that one worked just fine, my question is a special driver for it to make it work with the i mac A 1407 or I am out of luck. Thanks,

omg dude i was confused... i doubted my intelligence... you the man!

Man that's awesome! Thank you so much!

how do you adjust the brightness i'm confused please help me

How can you adjust monitor brightness on Windows?

Ever have any electrical issues with the rado¿ aftermarket sunroof in mine...a/c off... sun roof dripping 😢 battery voltage spiking 😱225VDC😨 AND new thermostat today 😢 😭. Any Silverado Lifter videos?😕

The transmission illumination, each position like park or d4 has its own bulb? Or is it just all 1 bulb for transmission display?

Great details. Thanks. I really appreciate your video