3 ай бұрын
3 ай бұрын
3 ай бұрын
4 ай бұрын
Пікірлер
@JoshuaDevin-q7t Күн бұрын
My problem is I locked my truck in 4 low drove approximately 20 feet shut it off. Got back in drove 20 more feet and now it refuses to come out of 4 low! I know how to shift it out by having it in Neutral so that's not the issue.
@jordchenard8163 12 күн бұрын
Oil is check without screw dipstick
@Simpsons.R.S 12 күн бұрын
@@jordchenard8163 yuppers 👍
@ironhorse8573 23 күн бұрын
Do you still need to pull your ebrake lever up or it doesn't matter when putting it on a jack stand, while changing brakes?
@Simpsons.R.S 23 күн бұрын
@@ironhorse8573 if you're changing rear brakes, you don't want to apply the parking brake/ebrake. Just leave it off and in service mode if you have electronic parking brakes.
@JWSGZ 25 күн бұрын
Hi bro, we are looking for collaborators for our new 3rd brake light. Are you interested in testing it out?
@Simpsons.R.S 25 күн бұрын
@@JWSGZ i would be. What vehicles do you have them for?
@JWSGZ 24 күн бұрын
@@Simpsons.R.S How can we send you more details?🙌
@Simpsons.R.S 24 күн бұрын
@JWSGZ you can email me at [email protected] if that works for you guys 👍
@ArtStamos 27 күн бұрын
4 amp battery would make it stronger
@DavidJStaff 28 күн бұрын
LOL...looking at buying a set of these rims and you drove past where I have hunted for years. Grew up in Indiana...
@Simpsons.R.S 28 күн бұрын
@@DavidJStaff haha nice! That's pretty awesome. Good old christmas tree capital of the world 😂😂
@williamjolly5539 Ай бұрын
I have a question not pertaining to the carb. I dont think. Its about the belt light. Do you know anthing about the belt light and the system that detects a bad belt? I have an 03 that the belt is toast, but I do have one coming, the light is flashing steady. I've checked the switch in the clutch cover. It's in the on position. I did the reset for limp mode but it doesn't seem to do like the videos I've seen. It does rev up, but the light is still flashing. Does anyone have any suggestions?
@jimdicksportinggoods6925 Ай бұрын
How have these cams held up? I’ve been eyeing these exact cams on eBay for a while. Hoping to pull the trigger
@uuulaalaa Ай бұрын
Wasn't working at first but than It did and well looking at the oem tools version one I think that one is better made than this
@foolz_3903 Ай бұрын
Great video until it refuses to go into brake service mode
@CRJames-s5y Ай бұрын
Twelve point 🫣
@Simpsons.R.S Ай бұрын
@@CRJames-s5y 😂😂 like that?
@bwagenberg Ай бұрын
How do you open the thermostat and drain/fill the block?
@Simpsons.R.S Ай бұрын
@bwagenberg once it pulls suction on the entire cooling system... you open the fluid up and it'll fill it all...both sides of the thermostat and the engine block.
@TJsVette Ай бұрын
Alright, I went and got mine today. It pulls a vacuum just fine, but it doesn't hold. Put it under an actual pressure test and found 3 small leaks. Got them fixed (just loose hose clamps and a broken fitting). I put it under another pressure test, and it held for over 10 min and the pressure never dropped. So I thought I was good. Hooked everything back up and started pulling another vacuum, but it still won't hold. Now, idk what the problem is.
@rickylee2477 12 күн бұрын
You have leaks
@TJsVette 12 күн бұрын
@rickylee2477 why would it hold pressure under a pressure test?
@rickylee2477 10 күн бұрын
@@TJsVette you have seals in the water pump that are designed to maintain pressure being the coolant system is pressurized. But don’t hold up as well under vacuum. When vehicles get lots of miles a strong c Vacuum on the system can definitely do damage and increase the wear on water pump seals. Sometimes causing premature failure and wear. The best safe method is to elevate the front end of the vehicle and burp with a spill free funnel.
@rickylee2477 10 күн бұрын
@@TJsVette so what I mean is the vacuum could very well be causing a leak thru water pump seal that isn’t present when the system is under pressure.
@TJsVette 10 күн бұрын
I replaced the water pump, thermostat and radiator last summer. I had a loose clamp and thought it was the new radiator. Got it all fixed and it holds coolant fine but this machine doesn't work lol.
@braapptorrr4630 Ай бұрын
Thanks for taking the time to make this. Always easier to do it once you’ve seen how it comes apart vs going in blind. Doing mine tonight!
@joebrewer5885 Ай бұрын
I can't find the port that you describe to verify top dead center, your picture was so close I didn't have any landmarks to go by .Can you help me find it?
@Simpsons.R.S Ай бұрын
Sorry it's took a little to get back to you. So the plug is right above where the pull starter is. Should be able to use a big flat head screw driver to get it out. Or carefully use pliers.
@joebrewer5885 Ай бұрын
@@Simpsons.R.S Thanks, I'm going to get this thing running, no matter what! Your videos are great!
@Simpsons.R.S Ай бұрын
@joebrewer5885 😂😂 thank you! You got this. Just take your time. Look everything over really well.
@joebrewer5885 28 күн бұрын
Thanks to both your carb and valve video's my 360 is running again!!! I believe the main problem was the fuel adjuster screw once had a very small o-ring that was completely dissolved. It had the hole to the carb throat partially clogged. I dug out the few remaining pieces of rubber, made sure it was perfectly clean and ordered a new fuel needle screw just to get that o-ring. I suspect it may be from ethanol that they put in gas that ate it up. After all it is a 2004 model. Thanks for your great advice!!!
@Simpsons.R.S 28 күн бұрын
@joebrewer5885 that's awesome! Good job man! Sometimes it's just something little. Thank you for the support!!!
@itstankbitches Ай бұрын
Speed collar removed, that more than doubles speed
@RaquelFinkelstein Ай бұрын
nice video thank you, you almost miss the lug nut to hold the rotor in place but you did mentioned it, good job, I didn't have the caliper piston tool so I ordered and will be replacing my rear breaks next week
@1320munks Ай бұрын
Good vid
@joebrewer5885 Ай бұрын
What do the wires on the bottom of the carb do?
@Simpsons.R.S Ай бұрын
So on some of the newer quads, they have wires on the carb. Most of them are just for the carb heater.
@TJsVette Ай бұрын
How has this held up over the time that you have had it?
@Simpsons.R.S Ай бұрын
@TJsVette honestly haven't had to use it much at all. Most projects I've done i don't need to use it. The cooling system on these cobras can be a pain, that's the main reason I got the tool.
@TJsVette Ай бұрын
@Simpsons.R.S lol I hear ya. I saw it today when I was in harbor freight and wondered if it was any good. Saw your video was from 4 years ago so I figured I would ask lol.
@Simpsons.R.S Ай бұрын
@TJsVette 😂😂 yaaa old video but it did work great.
@Dontoverthinkthis Ай бұрын
Love the song selection
@hunterboyce3423 Ай бұрын
What the hell is up with the red wire. Why doesn’t it just come with a key switch? I’m using this for my boat and what a pain im just pissed off at this point
@Simpsons.R.S Ай бұрын
Haha ya. You can run it with a switch to a 12v constant (to the battery) or wire it into something that turns on when the key is turned on. It's definitely kind of a pain
@rodneybedell9766 2 ай бұрын
camera man needs a raise
@jonbennett118 2 ай бұрын
Been chasing an issue with my prairie 360 its a 2005. Sometimes it starts sometimes and now more often then not, it will not just cranks away. I have done everything but the valves. I did the valves - well checked them and adjusted one two years ago. I am going nuts do you think it could be a valve issue with a no start situation. I have new plug, new carb (also rebuilt the other one and took it apart like 3 times before that) Its def getting fuel, i also checked the fuel switch that was replaced a while back also, its def getting fuel and def is getting spark. Nothing is blocking the air ducts. Its got all 3 main components for combustion but will not even chug just cranks and cranks. I am going crazy had it apart so many times lol.
@Simpsons.R.S 2 ай бұрын
Haha been there my man. So a few things to check. The one thing I like to do is spray a little starting fluid in her. Just to see if it'll fire. Thatll at least tell you that she's able to run. Did you put a ebay special carb on it or a factory one?
@jonbennett118 2 ай бұрын
@@Simpsons.R.S Amazon but its basically a complete replica, however it still wont start. It has started and ran with the factory but there is something else going on that i am pretty sure is not carb related. Because it stopped running suddenly and then would not start again.
@Simpsons.R.S 2 ай бұрын
@jonbennett118 ok so ya the amazon carbs look basically exactly the same... but I've had trouble with them working well, but it should still at least start with it. Ok well let's go over some basics. For spark you put a new plug in, did you check for spark while turning it over? And when the plug was in the engine....when you removed it, was it wet?
@jonbennett118 2 ай бұрын
@@Simpsons.R.S Yes plug has good spark held against engine when cranking. The plug was wet but dark and smelled of gas. The Carbs had fuel in them when i took back out. Recently the amazon carb came with a fuel filter so i can see that gas is getting to the carb. (Thanks for the help).
@Simpsons.R.S 2 ай бұрын
@jonbennett118 no worries. Ok so if it's really dark she's running rich. Could be a little to much fuel. But checking the valves both intake and exhaust is key as well. Making sure compression is there. Have you done a compression test on it by chance?
@King_w0092 2 ай бұрын
So the hose on the bottom of the carb was broken on mine and wasn’t attached to anything does anyone know where it attaches or if it does
@Simpsons.R.S 2 ай бұрын
@Wyatt-jy8sg the carbs have a rubber line on the bottom for the over flow. It's a safety feature you could say. So if the float sticks... it'll leak the gas through there and not into the engine. It just runs down beside/below the engine, so it leaks in the ground. Not on the engine.
@King_w0092 2 ай бұрын
@ is there any way to fix that because it has been leaking gas almost constantly
@Simpsons.R.S 2 ай бұрын
@Wyatt-jy8sg yes you can give this a shot. Take the carb apart. Pull the floats out, and the float needle. Clean it really well and put it back in. If it still leaks you can try to adjust the float and see if it stops leaks. But adjusting it can cause other issues. I'd recommend just buying a new needle and seat if cleaning it doesn't fix the issue.
@King_w0092 2 ай бұрын
@ thank you very much hasn’t leaked yet
@d.l.horton2093 2 ай бұрын
What cheaper oil can I use besides Polaris special golden shower oil? I know for the front hubs I can use Type F trans fluid. (But for the amount you use to refill those hubs one quart will last for 30 oil changes.) I can use 10w 30 for the balancer shaft. But what can I use for the transmission? I want to use gear oil but I'm not sure? I have the 2 stroke 400 sportsman so for premix or the oil bottle full synthetic is good for clean and low smoke. I use marine 2 stroke. Caster or conventional oil is good for lawn mowers.
@Simpsons.R.S 2 ай бұрын
@d.l.horton2093 so unfortunately I can't advise anything besides their stuff....which is very annoying because of the price. Trust me. I do a lot of polaris services and I wish I could run cheaper stuff... if the customer wants to run something different. It's their money 😂
@allanfranco4464 2 ай бұрын
PUT #1PERMATEX ON OUTER PART OF SEAL TO SECURE SEAL FROM COMING OUT AND GREASE AXLE AND WHEEL HUB BEFORE INSTALLING CAN SEE YOUR NOT VERY EXPERIENCED, EVERYONE WANTS TO MAKE A VIDEO
@Simpsons.R.S 2 ай бұрын
@allanfranco4464 little rude but lets talk about it. This video is 3 years old and the mower has been used each week each summer for those 3 years and the seal has never came out. So yes you can use permatex, but you don't have to. And greasing the axle and hub before installing.... explain to me why you would have to do that? This tractor was a few years old before the job was done and everything came off very easily...even though it was never greased.
@joeliggio788 2 ай бұрын
How to remove a carburetor from a 350 Honda four wheeler
@Simpsons.R.S 2 ай бұрын
@joeliggio788 once we get an approval to do one ill definitely make a video on it 💪
@Shawn-h1l 2 ай бұрын
What kind of ramps are those?
@Simpsons.R.S 2 ай бұрын
They are rhino ramps. You can get them at Walmart for about $50. Harbor freight has ramps like them too.
@Shawn-h1l 2 ай бұрын
@ Thanks for the reply I got to start doing my own oil change on my Durango. Much appreciated
@Simpsons.R.S 2 ай бұрын
Nice! Hopefully it'll save you a few bucks!
@jorgelujan5055 2 ай бұрын
Hello, my battery says 12.7 volts, but the bike wont turn on (usually the green neutral light comes in when i turn the key). It wint start and wont turn on
@Simpsons.R.S 2 ай бұрын
So it can be a few different things. When you turn the key... does anything come on? Like the dash? Can the lights turn on?
@NewNew-mk5xo Ай бұрын
@@Simpsons.R.S same here, but yes the dash and lights
@StaticFreighter101 2 ай бұрын
Thank you that helped a lot
@95PurpleHaze 2 ай бұрын
Thanks for the video. My switch has a dead spot when you go full turn and I didn't know how to remove the original.
@SudoTragic 2 ай бұрын
not supposed to check the oil with dipstick screwed in
@Simpsons.R.S 2 ай бұрын
Yupp you're right. Kinda just a habit. Some machines you do. Some you don't. We change the oil every 2 races so I don't feel it's quite as important as someone that's not changing it as frequently.
@SudoTragic Ай бұрын
@@Simpsons.R.S just wanted to make sure you knew brother. alot of folks dont and just wanted to spead the word lol.
@mikecipparone5383 2 ай бұрын
please let me know what slug kit you ordered too. I'll do the same
@Simpsons.R.S 2 ай бұрын
www.ebay.com/itm/314356630476?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=tcv9J0ytSUi&sssrc=4429486&ssuid=Ca0_dCHlTaq&var=&widget_ver=artemis&media=COPY
@Simpsons.R.S 2 ай бұрын
If you go on ebay or amazon... type in rhino 450 slug kit. Those are the ones I put in. They are cheap but they work
@mikecipparone5383 2 ай бұрын
was the threads on the wet clutch reversed? left to tighten and did you reuse the nut?
@Simpsons.R.S 2 ай бұрын
They are normal threads. Righty tighty!
@vvvv-lu8zi 2 ай бұрын
it tells you if you have a leack. but it wont tells you from where this tool i good for filling the system but i believ not good at spotting a leack ( where does it leack)
@wpistol 2 ай бұрын
Crush washers are your friend.
@alancowart4418 2 ай бұрын
Do you adjust both at same time such as first TDC
@Simpsons.R.S 2 ай бұрын
Yupp you can check them both
@stevesmith1493 3 ай бұрын
The vertical float switch is the key. They have a better one w a piggy back switch.
@stevesmith1493 3 ай бұрын
I have used them for years! Never had one go out yet. I own a crawlspace repair company. Amazon has some Superior pumps for the same $$ w 3 year warranty though.
@Simpsons.R.S 3 ай бұрын
I've had absolutely 0 issues with this one. Even when the basement flooded and it ran almost all night without us knowing. She pushed through. I'd definitely recommend it to anyone haha
@jsprad0703 3 ай бұрын
What is the cable called that goes on the neutral reverse switch? I can’t find it on the atv diagram anywhere. The end of mine it broke and won’t connect
@Simpsons.R.S 3 ай бұрын
22880-HN5-A80 That's Hondas oem part number for the reverse cable.
@jonasluvnjk6113 3 ай бұрын
I cleaned the siding of a mobile home, green mold, and LA’s awesome m,worked as magic, I highly recommend this! You have to rinse it.
@richardepstein3494 3 ай бұрын
You definitely overfilled your oil using 5 qts. I've got an 18 Trek and the specs call for 4.7 and even at that quantity the oil level is above the dip stick full mark
@Simpsons.R.S 3 ай бұрын
The 2018 trek calls for about 4.6 quarts. The 2015 impreza calls for 5.1. Every oil change was right where it needed to be on the dip stick.
@TheAwmartin 2 ай бұрын
different cars..
@rodrigogmz2828 3 ай бұрын
What was the paste you use on before you put the rotor on
@Simpsons.R.S 3 ай бұрын
I usually just use anti seize.
@일천만이산가족위원회 3 ай бұрын
좋은 정보 감사합니다
@itsbeatzz9 3 ай бұрын
I have a question so I have a 2x4 Honda rancher 350 2003 es does the transmission take oil
@Simpsons.R.S 3 ай бұрын
@HudsonsGarage298 it should be all the same. Motor and trans use the same oil. So if you change the engine oil, you're changing the trans fluid too.
@itsbeatzz9 3 ай бұрын
@@Simpsons.R.S oh ok thanks so much
@BeardedDaddyD 3 ай бұрын
We're all professionals... nothing to see here 😂
@N0izyb0i 3 ай бұрын
My drain plus was rusted after adding some wd 40 my wrench broke lol great day
@Simpsons.R.S 3 ай бұрын
😬😬 ouch!
@RasSosa 3 ай бұрын
good video but i didn't like that you had already removed the gas tank. I am having problems finding a video on how to do this on a this very model. I am trying to change the spark plug for a tune up.... :(
@Simpsons.R.S 3 ай бұрын
@RasSosa kzbin.info/www/bejne/qYGxY2SBgpiEkK8si=zr5XxoYV4LRJbA3i this is my other video. That might help you with removing the tank!
@DoubleD.Racing 3 ай бұрын
Great video Josh! 😎 Thanks Helmans!