Brock Vista

Good stuff

Screw you all you doing is complaining 😅

Where does the line side neutral tie into this equation? You are showing your switch leg going to each brass terminal, but you don't mention where your incoming line neutral goes?

What's the minimum runtime

No water in my 1" conduit for my pool pump I installed in 2007. Put shop vac on one end no water came out of it I'm in AZ dry here.

quick question , how height can be a transformer go above finish floor ?

Everytime I see that EMT to MC connector, I fail to understand how the NEC doesn't consider the MC side clamp a Romex clamp.

Now what’s crazy is a corner ground three phase system.

I’ve seen it several times here in Houston. It’s not uncommon to see when a residential street backs up to a street that’s commercial and on three phase.

Thank you for keeping it simple understand perfectly

I think you should have included the instruction on a unit possessing a neutral.

Thank you for sharing your knowledge.

Hello is there any way i could have a phone call with you?

That’s 2000s housing boom work for you.

Honestly you did amazing. Best explanation.

0:35 What will happen in case of fire?

Is that second panel guts upside down?

Great information. Looking forward for more.

Thanks for the vid. On 277/480: you can get 277V phase to neutral on BOTH Y and Delta configurations?

Your camera and lighting is awful we cannot see everything clearly. You might want to re-do this video

very nicely done!

Can a 3 phase breaker be installed on circuit 5,7,9. That would be c,b,a.. or does it have to be a,b,c

I knew about abc this video taught me where to land each one thank you

When those conductors short, it knocks out the transformer feeding a multitude of houses.😳

Where are the actual circuits located if not in the panel next to it? I’d imagine a 120v coil.

Looks damn good, I agree they did do a nice job.

Thanks for sharing, great learning experience.

Good

Hi , there . I have a question about when the Abdul system is triggered, I can see on your diagram that light & outlets all cut out by microswitch. But you didn’t mention how a the Exhaust Fan will turning On ? Since the the switch is on open position.

Ty

I have a 14DF32AC 81 3 phase for a well water pump motor I'm trying to put a hour meter on it . does it connect where coil signal comes in to close thus activating the power?

I am in a princess. And this video is very helpful, thank you. I'm sorry my spelling is not the best

Based on article 450.13 b, it says that a transformer larger than 50kva cannot be installed above the drop ceiling.

I live in Phoenix I heard about a housing tract that was built they sold 3 phase power as a cost savings advantage. I believe it was 1960's at least didn't also have aluminum wire like I ended up with in my later 1970's home.

Can't tell you how many of these I've seen in 30 years!

Its NOT legal to use a heavy wall coupling to join anything but threaded pipe. Reason being rigid conduit has a tapered thread and type NM, AC,MC, EMT, Greenfield connectors & chase nipples do not have tapered threads so this could cause a problem on clearing thousands of amps during a dead short. Yep don't know one sparky who has not used coupling to join connectors. I been reading the quarter million word code book for over 50 years and still learning.

Best practice for any armored cable is to cut the admire end at a 45 degree angle & spend 2 seconds to I stall anti short bushings. Yes they are not required by NEC but the large hospital that I retired from it was mandatory to use anti short bhshings.

Thank you! Sign guy here buried in learning the NEC code book, and this video helped me with visualizing this!

keeep it up

What a video been looking for this for years. Thanks a bunch.

Wow great find. The pipes need to be completely redone to allow clearance

Great video

glory holes

At 2:35 is this a MWBC or a switched receptacle or something?

I'm a general handyman. I always have people who want pricing over the phone. I won't do it. Partnered up with an electrician. He cuts holes in drywall, I patch them. Homeowners want me to cut corners after an electrician gives them a price they don't like. Not taking the liability

I know its an old vid but better late than never tnx for sharing🤙

Hi I need to buck down from 237v to 220v for a pneumatic elevator. The sales man stated I need this same transformer 416-1131-000. I feel that I would need a 16/32 secondary transformer to get me to 221v ac. What do you think?

Awesome video! 😎👍

I am electricion India 🇮🇳🇮🇳🇮🇳🇮🇳🇮🇳🇹🇹🇹🇹🇹🇹🇮🇳🇮🇳🇮🇳🇮🇳i am entrested