I had bought this to hide my keys since I like to myself out of my house. I threw away where I wrote down the code. So after watching this I got the code again and now it’s going in the trash. That was way too easy to get into. 😮

Just noticed my 2020 Laramie Longhorn dash is bubbling. It just went over 60K. Any luck with getting it replaced outside of the warranty?

How to wire Dig Uno? I didn't find Q1R pin

Raid 10 it

If this doesn't work.. just put it in Neutral

Area man FINALLY GETS TO THE DAMN POINT OF THE VIDEO at 2:34.

How long does it take for the ice to start forming after you do these steps?

Did you do a valve gap adjusting?

Video is flipped wrong.

I have that same model in a double oven.I never really use the bottom one. I noticed that the baked goods were coming out a little dry. I bought a thermometer and I believe the oven is running a little hotter then it should. I am trying to figure out how to lower the temp. It should be 400 but I think it says 425

I figured out how to do this with three digit bicycle chain locks, when I was very young and every combination lock, like this, even some padlock type combination locks, I can open. i've always done this the same way. just by putting pressure on the release and turn it till I either couldn't get it. Turn it till it would not turn any further. Then I would have to let off of the release, and it would be the next number up and then the next number and the next number all the same way. they assigned us push button locks for our lockers. In Jr High the shank was smooth. There was nothing to catch it except the spring.On the other side. i figured out you could raise the lock to where it was upside down in the latch. Then , push on it, the top part of the latch was just the right size so you could take the lock lock, turn it upside down. hit it against the locker and unlock. The shank was long enough to hang off the bottom of the latch, but turned upside down. The shank was too small, so the latch was like a pry bar and when pressed against it pryed the shank away from the lock it popped open it wasn't long before the entire school found out.

Work for me, thanks.

My 2019 Linited has the same dash issue. Please send me any info so I can reach out for repair. Thx

Just a word of caution...any time you alter or eliminate an electrical function or alter a computer command on your truck. YOU JUST VOIDED YOUR WARRANTY! THIS IS A FACT.

Yup, It worked for me. 👍

Where do you buy the lights ?

I have a sentry safe that is in the locked position with the door open meaning the bolts are in the outward position and they cannot be pushed back in manually far enough to be able to clear the plastic cover on the inside any suggestions?

Theres no way there's actually a video about. I'm sure you've seen the barn metal showers. Imagine LED lights in the j-channel of a white barn metal shower

Mine is old so i push on every button but they all feel about the same. Any advice please

Where did you get your track?

23:40 The Procell battery is Durecell commercial brand. It's the same thing they (at Liberty Safe told me.

Holy crap I got seasick, watching this video invest in a tripod!

My Whirlpool calibration is giving me the BLUES. I can't for nothing do it right. Any ANY ADVICE? PLEEEEEASE HELP ME.

I have a 2023 model Nordic track EXP14i tread mill. I beat the hell out on the screen everywhere to get to the screen you mentioned but no avail. I pressed the re-set button , no worke. The screen is stuck at IFIT login screen. Any suggestions?

It was 375, not 475.

I’m having issues with my touch panel that dispenses water and ice. The ice works fine but the water isn’t coming out at all. The water and ice switch both lights up on the dispenser at the same time, it’s suppose to light up one at a time. There was a short period where the dispenser automatically locks in the middle of me getting ice! I have to go into the touchscreen and digital unlock it.

Great video I forgot take off the cap brake fluid. Is it bad?

Where did you get the NEMA enclosure?

I gonna be building an oven do I have to do anything to the original element controller like re wire it for the pid control

Great installation... have a couple of questions... what did you use for the track? Also, what type of connectors did you use on the top of the box to connect to the LED strips?

What is the target distance and height? At least a starting point? Thanks.

Any issues with the digital lock so far?

Thanks shipmate

You should never drive into oncoming traffic with your hibeams on. You should switch to low beams until you pass the oncoming traffic.

A tip when the touch stops working on the lcd, even with the reboot.... Plug a mouse into the USB port and you can use it as a pc, without having to completely replace the lcd and spend hundreds of dollars.

Thx

Real good video, very much appreciated Mr BigNasty 🤠

My 24kW does not allow me to reset maintenance.

My family forgot the code for our kiddle safe 11 years ago they would pay whoever mangaged to open it 50$. I thank you very much for making this video, it was a great help😊

What about in between the annual service? We had ours run for 6 days after Beryl.

Battery is critical, often overlooked. Before doing anything, check the trickle voltage to the battery, that's what keeps it charged between runs. Should be over 13v generally. If not, battery isn't getting charged to start the unit when needed. I've changed the standard clamp leads to marine grade terminals, cables are attached with lug ends, then sprayed with NOCO anti corrosion spray. When the unit is running, battery voltage should be over 14v, and yes battery should have full cell levels of distilled water. If you disconnect battery, Generac procedure is to remove 7.5 amp fuse at control unit, then disconnect white charge wire above the battery. After reconnecting battery, reconnect charge wire and insert 7.5 amp fuse. Then check all trickle and run voltages. May all sound like overkill, but the worst time to find out battery issues is when you lose primary power......

The corrosion you see on the battery terminal, cost me $300 for a service call to my rental cabin. The Guy cleaned the terminals. That was expensive 10 minutes. I will put in a new AGM Group 35 4year battery, best price Walmart.

Have the exact lock in video. I could not feel jackall pushing the buttons. I read the comments and saw people posting using wd40 on the buttons and they started feeling the push back from the buttons. I can confirm 100% success after working break free oil through the buttons. I let it sit for a few days button side up and was able to get the code. To be clear, I 100% could not feel anything until using the oil.

good video. change the setting on your camera so you are oriented properly. That way you are removing your filter instead of tightening it :)

Great vid! Bambu have lots of documentation but honestly they do a bad job of explaining the simple stuff, like how to pause on a layer by right clicking the slider. I have been wanting to do hueforge prints and now i know how they pause for manual changes.

Hi, our family hub freezer isn't functioning as it should. It is warm inside, the temperature on screen is -19 but the actual temperature inside is about -7.

I have a 2019 RAM and I don't see anything like you're showing

Can’t thank you enough for this video man, thank you so much for taking the trouble to share, I have been pulling my hair out for weeks trying to resolve this. I was just about to give up when I came across this so thanks again from the Emerald Isle 😀

One tip, running the engine up to temperature before draining the oil will help with drain it faster/completely. Good diy video!

Couldn't you have powered the dig quads with the 12 volt power then take 5 volts from it to the relays?