How do you make sure the debris doesn't go inside the line?

very nice

How do you avoid that a small quantity of fluid passes through the valve when removing the tapping tool and before closing the valve?

У нас режут через специальный вентиль, который потом остаётся. Без всей этой возни с шиберной пластиной.

Very nice fantastic Job ......

whether the hurricane is in a place where the passage is of a dangerous combustion or ignited product ?

this machine is only for water pipes

Brasil🇧🇷

BRASIL 🇧🇷🙄😎👍

muy largo para tan poco contenido.Muy aburrido

boa tarde eu gostaria de comprar um equipamento dese como faso meu imail e [email protected] meu numero tel 55 21 970322644

All that ppe seriously...

Bu kadar şey için bir video bu kadar uzatılmaz insanların zamanını çalmak demektir bu ben bu videoyu kimseye tavsye etmiyorum

Just waited to see if remembering to open the valve was in the instructions!!!.....tapping thru 2 gates a stem and the pipe make for a real bad day .....don't laugh....it's been done more times than u would ever believe!!! Personally, I would have opened that valve before doing anything else....my second check of valve position would have been when I measured cutter travel thru the valve body not outside of it.

As tedious as the task is it is very important to ensure the sound track is included with every tool purchase.

And why would you do this demonstration on SS pipe? One good way to burn up a bit and hole saw.

This aint Pipe Fitting 101 show me the fucking tapping machine.

I've done about 7 hottaps in my day it's scary when you first light up. the welding inspector ut'ed the pipe(that's to check how thick it is) I asked him to stick around while I first lit up, should of seen the look on his face... he did stay...12 " weldolets took most of the day...... 342 retired.

Did you put the gasket? I [email protected]

I'm professional plumber needs To work abroad .mother land is Egypt .now work in saudi arabia mobile no.is 00966569248737 pls I need it tnx

I noticed the magnet for shavings and dick capture, what would the process be if one wanted to do this on stainless steel?

The background muzak... do I have to play it out loud while tapping, or can I have it through my headphones???

Ok... good vid but... Who would do all that set up in full Garb....including brand new gloves. Not this sailor.

Jamming out to hot tapping music.

I came for the tapping and stayed for the scruff

Not sure why I sat through that. But I learned a new skill ill never ever need

METAL SAMPLES is the best hot tap tool known to man, we just got it up here for the Arctic Oil lines and it is flawless!!! EVEN IN -50 BELOW !!!!!!!!!!!!!!!!

I hope you don't hire the same people for drilling like the ones you hired to make this video... Worst grammar and spelling ever..

Esto es para una perforación muy ligera, Y demostrarlo en una linea viva. NO convencido.

pay 200 an hour, i still would for that kind of job... its akiller explosion... hey ill trade you an iphone 4 both of you kidneyss.. jahajjaj

The pilot drill did not appear to have a retaining clip that secures the the coupon that the whole cutter creates ? if not its going in the system.

If you have to read the instructions you should not be doing this on a live pipe.

Hi , What type of drill is being coupled to the shaft ?

"Carrie on drilling"? With spelling and proofreading like that I wouldn't let you unclog my toilet.

this seems like such a complex procedure. i didnt notice any torquing and perhaps one measurement taken. how come the flange on the tapping machine has far less bolt holes than the flange on the valve?

awesome

Я понимаю что технология отработана, но я бы наверное перестраховался. Сначала испытал место врезки и участок трубопровода, до ближайших задвижек, а потом демонтировал и заваривал шибер.

Where are these tapping machine for sale?