Dr. DansGarage

Пікірлер

@tri5garage544 Күн бұрын

It turned out great. Personally a few flaws make a truck look even better, I don’t know why.

@karmafarbus160 10 күн бұрын

I tuned in for the Skookum

@captainedc Ай бұрын

Great video ! Very helpful. Finally just starting using the same gun (but purple) my wife bought me probably 15 years ago. So far I really like it. Only issue is the needle seat nut seems weird and if you don't have it set just right it drips paint everywhere. Not sure why. Just picked up a used FLG3 but the bottom can type. Figured it might be good for primers ?

@user-qe9de6lj6w Ай бұрын

Dr. respectfully suggest you stick to medicine

@Big-H517 Ай бұрын

Dumb question probably for a future project. Can you make it hot swappable with an iPad mini?

@dr.dansgarage Ай бұрын

That’s a good question. It would be possible to attach an ipad with a specifically sized “plug” to fit into the main body instead of the paper. That size is 101.6 x 151.2 mm. The only reason to do so would be if one wanted to switch back and forth between paper and ipad. Otherwise, I believe there are other ipad options available.

@SHREDDERgb Ай бұрын

It's pretty cool man!

@AjitMD Ай бұрын

How much to bring this airplane to modern standards including avionics, autopilot, communication, controls and general overhaul to get to max reliability?

@peteormond2828 Ай бұрын

You'll be able to hire it out to the RCMP Swat team?

@peteormond2828 Ай бұрын

I've binge watched your videos - thanks. Have you considered making that centre window panel with a hinge to access the bow platform ?

@dr.dansgarage Ай бұрын

That would be handy. My plan is to walk around the sides. There is enough room to step but I will add some grip tape in case it gets slippery. The boat is 95% done. I’ll get it completely finished this summer.

@peteormond2828 Ай бұрын

Good job & thanks for the video. Trim tabs on the rudders to fine tune pulling left or right ?

@peteormond2828 Ай бұрын

Shoulda sneaked a heated seat for the driver.

@peteormond2828 Ай бұрын

Heating the balancer would've done wonders for the crankshaft seal ?

@peteormond2828 Ай бұрын

I personally would have stayed away from that serpentine belt- it may make a mess of your return line if it lets go. And using hard tubing for the return line - it being so close to the extremely hot turbo. I'm liking your videos - Thanks.

@dr.dansgarage Ай бұрын

Good thoughts, thanks! I have revised the oil lines a bit since.

@peteormond2828 Ай бұрын

Looks sturdy enough. Did you allow enough clearance above the curved strut ? Just in case you need to drop the sump, if you need to work on the bottom end - so you don't need to lift the motor with all the extra hoses, lines and exhaust tubing, that'll need disconnecting

@peteormond2828 Ай бұрын

P - Factor ? kzbin.info/www/bejne/ppfRg6tofsd3gs0&ab_channel=aviacionenespa%C3%B1ol kzbin.info/www/bejne/rJ3Yemefrqx8qpo&ab_channel=EverythingAviation kzbin.info/www/bejne/rJCYgYWJo8l-j9E&ab_channel=flight-club

@BLACKCLOUDFORD Ай бұрын

Seriously ? No sound clip ?

@dr.dansgarage Ай бұрын

Hmm, fair point. In the water it sounds about the same as it did before. A mild rumble at most. Definitely not loud.

@macarthurguneratne373 Ай бұрын

First time i am seeing a 3 bladed propeller .I have about 850 hours on the 337

@TREEHUGGAH1 2 ай бұрын

sure is a beauty! you didnt fly over pa/ny border near delaware river on memorial day weekend? took some nice shots of one that did fly over my property.

@dr.dansgarage 2 ай бұрын

Unfortunately I haven’t had the pleasure of being out that way with it. Must’ve been another. Cheers

@jasonsullivan8001 3 ай бұрын

Great video I turned out really good. How do you like it?

@dr.dansgarage 3 ай бұрын

Thanks! I like it a lot. I think it looks good and sounds good.

@HPMIKE55 11 күн бұрын

@@dr.dansgaragegreat job and how much would you sell that for??? 😎👍🏻

@dr.dansgarage 11 күн бұрын

@@HPMIKE55 can’t sell it, enjoying it too much!

@HPMIKE55 11 күн бұрын

@@dr.dansgarage I don’t blame you the paint job came out really nice. Keep up the great job! 😎👍🏻

@gene8933 3 ай бұрын

wow those dumbbells provided a lot of help. NICE JOB!

@gagebreaux9840 3 ай бұрын

this is some incredible workman ship from such a small channel! Wish you luck on your yt journey

@Riley-do5bp 3 ай бұрын

The attention to detail in this build is incredible. Great job! Deserves more attention, this is how it’s done.

@MaximumPasta 3 ай бұрын

Super clean build and it sounds great in my headphones 🔊🔊

@danieljones8587 3 ай бұрын

Wow! The finish on your sub looked outstanding. Excellent job!

@Itesmassive 3 ай бұрын

Why not delete the sway bar as well?

@dr.dansgarage 3 ай бұрын

As it is right now is a pretty good mix of off-road and on-road capability.

@Fluffymcfluffersons 3 ай бұрын

Another thing that will help a ton is adding or moving the foot pegs to the rear behind the engine it helps a ton

@dr.dansgarage 3 ай бұрын

Good point. I think I’m going to do this.

@Ruieinal 4 ай бұрын

Quedó perfecto, tengo un samurai al que me gustaría hacerle lo mismo, gracias por la idea 😄😄

@schillaci5590 4 ай бұрын

If you ever want to sell it, please do let me know!

@biologicalboutique407 4 ай бұрын

Looks GREAT!

@timfox8121 5 ай бұрын

What did you do with that old top???

@dr.dansgarage 5 ай бұрын

I sold it the old top. I’m sure it’s still getting good use with somebody else. I haven’t missed it though.

@olivierboulogne5851 5 ай бұрын

Hello, have you changed anything on the stabilizer bar?

@chuckhuff7123 5 ай бұрын

All my little brother and I wanted as kids was a western auto mini bike, unfortunately they were over 300 buck back in mid 60s throu the 1970s. We could not do that😢. Still I would like to own a Western Flyer mini bike😢.

@gamesupcomingtop1548 5 ай бұрын

very soothing videos, i like it🙂

@therealblakekirkham5701 5 ай бұрын

What glue did you end up using

@dr.dansgarage 5 ай бұрын

JB weld

@mattm7430 5 ай бұрын

Looking forward to the O-2 paint job and marking rocket rail install episodes! Dr Dan, love where you’re headed with this.

@ColonelCowbell 6 ай бұрын

This looks like a good improvement over the older horizontal setups. Questions: Can you tell me what size (in GPH and cone angle) oil-burner orifice you used? What air pressure are you using to atomize the oil? And what oil consumption rate (GPH) are you getting with that size orifice and air pressure? Thank you for posting up this video.

@dr.dansgarage 6 ай бұрын

I don’t remember the nozzle size but probably 0.35. I think I ran it at about 60 psi. I never kept track of the burn rate; I would just add oil to the tank when it was running low. I still have the entire unit but it’s been removed for several years.

@Winkleo.x 6 ай бұрын

I have these on an FJ, second set. They're great for off-road in Oregon.

@Dr650rob 6 ай бұрын

The solenoid goes under the gas tank, using a ubolt type of mount to one of the frame tubes going down

@ruggedmute5858 6 ай бұрын

How do the clip go from the plow to the mount? I can’t figure them out

@woodwelder 6 ай бұрын

Nice ! Those props look special .. and expensive !! Tell us more .. happy flying

@dr.dansgarage 6 ай бұрын

Yeah they are MT composite props and they are expensive. Thankfully they were on the plane when I bought it so I didn't have to do the purchase price. The purported benefit is less noise and vibration, maybe a bit better climb speed. I don't have anything to compare them to so probably true but unverified by me. What I can confirm is that they are more fragile than aluminum props. The rear prop is susceptible to damage from gravel or debris. It has happened to me. They are repairable but it costs money.

@ArtAaron 7 ай бұрын

What engines are installed? Props are composite? What kind of airspeed vs fuel flow do you get? Thanks.

@user-vf8yr9mo2e 7 ай бұрын

Videos

@iancormie9916 7 ай бұрын

Hope you were wearing a mask when you cut that thing open.

@Brumasterj 7 ай бұрын

Nice torque wrench:) Click LOL

@lawdpleasehelpmeno 7 ай бұрын

Amazing condition! What a great plane.

@camelblue713 7 ай бұрын

Did you Fluid Film the Chevy?

@dr.dansgarage 7 ай бұрын

Are you referring to rust prevention? I have in the past but didn’t this year

@camelblue713 7 ай бұрын

@@dr.dansgarage yes exactly, keep good stuff alive

@gamesupcomingtop1548 7 ай бұрын

🤟👍

@JustSomeGuy38790 7 ай бұрын

You still have the samurai and skymaster? Great video btw!

@dr.dansgarage 7 ай бұрын

Yeah, still have them both. Flying when possible, but not enough hours in the day.

@MuniNadan-rk4jd 7 ай бұрын

That thing got so thin you keep sanding it. Get a new ignition barrel a universal one will also work cost around $35aud. Maybe your starter solenoid is bad but you think it's the switch. Turn on ignition and go touch a screw driver across starter's positive and negative solenoid terminals to see if it starts directly that way.

@dr.dansgarage 7 ай бұрын

When I did this, a replacement ignition was out of stock everywhere. I've since purchased and received a new one but I haven't had to replace it yet because the repaired one is still working fine.

@kevine9986 7 ай бұрын

Where did you find the plastic fender flair mounts

Ең жақсы KZbin

Пікірлер