Hose is for the impulse pressures connecting crankcase to fuel pump side of the carburetor

Aloha from Hawaii…thank you for the hints and tips! Our first Miata was a 2015 Club PRHT w/ auto but a week ago we picked up a stick shift 2006 Ltd Edition and I’ll use your method to check/clear drains. I had to laugh during your video as I’m also a trombone player and your solution with the slide cleaner had me going, “Now why didn’t I think of that??”

I find it easier to push the trombone cleaner up from under the car until it comes out the top

My transformer between the 2 tabs is 1500 ohms. Does that mean its bad?

One of the best instructional videos I’ve ever watched on KZbin. Very informative and professionally done; thank you so much!

This works brilliantly! I was able to quickly and easily clean my drains thanks to this hack.

Did it work long term?

Homelite still run with the best of them

Thank you so much I’ve had water sloshing around my feet nobody could find the drain holes even jiffy lube was clueless lol 😂

Homelite chainsaws are trash.

Youre the man! Helped me so much

My mx5 convertible leaks warter in the footwells so I will be trying this in the near future 👍

Parking under a tree is not recommended but sometimes I have too. So I invested in a throw over covering the hood. Also it rains a lot in my city and frost at the moment. Helpful video and I have clear drains holes at the moment. Thanks.

Looks like the ground on your battery could be a problem!

I just love it when folks use their heads and share there ideas with others 😊. Needing to try this tomorrow as my NC Boat took on some water this week! Thanks for sharing!!

Thanks a lot !!! Those rubber intake boots 'can't' take the gas' for too' many years !

Great video. Thank you.

For years I have been unable to clean the drain holes with the trombone brush so I was taking it to dealer and paying about $200 each time. Using the tube as you suggested worked great, so easy. Big, big saving going forward. Thanks a ton!

Could you not have used a air hose with a compressor? Wouldn't forced air going into a hole unblocked it, therefore not necessary to use water to flush it? Just a thought. What do you think?

I’m betting this problem wasn’t caused by the kill switch but probably by the PTO interlock switch not being in the correct position (ie operated when it shouldn’t be or not operated when it should be). The wiring “diagram” is very poorly done and doesn’t show the internals of the PTO interlock switch.

Thanks for the video...very direct and informative! 😀

incapable de faire une vidéo!!

🅿🆁🅾🅼🅾🆂🅼

Thanks for your video, the rubber hose really helped me with one clogged up drainhole🙏

What size tube do you recommend?

I also could not get the trombone cleaner down the passenger side drain hole. After I used a really fat straw to push the trombone wire through I was able to get it out the bottom. I had the car 14 years and only ever got the driver side to open. Thanks a million!!!! Now I have both drains working great 👍😃!!

Thanks for that, works a treat. Very easy to miss the drain hole without the tube to guide the brush in.

I'm a 75 year old and l have paid out for this to be done before at great expense ,so l thought I would have a go myself ,this was a brillian video it works thank you

Thank you! No body explaints this in others videos. The grownth and the negative havent get continiuty. If this hapens the motor wont have spark. Many thks. I have this problem but now I can understand it.

Thank you! All of the other videos would not show where this stupid hole was. It would always show a close up with bad lighting and people saying, "oh yeah right behind the seat." WHERE?! Thank you.

Great job. Thanks

You need to speak louder when troubleshooting component

Couldn't hear him.

clean the contact points... looks like yours are rusted... corroded... the battery let you know the contact points were not able to make the relay open/close..

Thank you so much! I could not for the life of me get any kind of brush down there, it was so clogged. Using your tip I had a small length of plastic tubing that was just large enough for the brush I bought. And with another source giving me a more precise location 10 o'clock if you're facing the passenger side from the driver's or 2 o'clock if you're facing the driver's from the passenger side I was able to get the clog cleared and it should now be draining properly.

Great tip. I will try this - like you I have not been able to find the drain hole with the trombone cleaner alone. Keeping my fingers crossed! What was not clear by the video is if the hose will naturally line up with the drain plug once inserted - what stops the hose from directing the trombone cleaner in the wrong direction?

Excellent,,,a lot of thanks

Do you have a carb for the 360 you will sell its a walbro 39A

Well I did this exactly as he said I found a hose and I did exactly what he said.the passenger side is different to the drivers side But having said that I managed to get the trombone cleaner in there and cleaned all the bits .I then stuck boiling water down the hole and finally I could see the end results I tried to find the holes without the hose but still struggled so tried it one more time with the hose. I have been trying to resolve this for few hours and for couple of weekends. So far I just wanted to say a big thank you for the tip it worked . Kind regards

Thank you so much I tried this today and spent 2 hours trying to find the hole ,I wilm try again tomorrow if this works I would say this is the best video Like yours mine is blocked and I tired with a coat hanger but that did not work I have the trombone cleaner, but once you said if this works I am just happy to try this I appreciate your help Kind regards

I have the same car except mine is a soft top. But I was going to clean mine but I wasn't sure what I was looking for. Now I know, thanks.

Thanks for sharing. But dude, you need a tripod.

Thank you. Great idea!

Helpful video! Thankyou!

bouncing cameras make me dizzy trying to keep up ---mount on tri pod

m lead on ing. switch is where gd is coming from only in the off pos if gd is on that lead in run pos. the ing switch is bad its coming apart in side i dont think a relay is involved in this you can run with this lead cut till you get a switch if you have a solenoid on the carb that will kill the eng in the off pos for those folks with this prob this wire on mine is awhite wire just above the muffler you can cut this lead and cut grass ok till you get a switch------ once a switch starts failing it causes other problems

Awesome! Thank you soo much from people who just tinker and don’t work on this stuff for a living. Logical and easy to understand what you were looking for. I Will use this information to troubleshoot my riding lawnmower! Thanks again!

This video is 6 years old, so I doubt you’ll see this comment, but thanks for making this video. There’s not much info on KZbin about this chainsaw and this video just helped a lot!

Make sure your keyswitch is in the run position. Stop position grounds that wire.

Whoa....filmed in Katherine Hepburn vision!!