Nice saple❤always

Muito bom, 👏

Looks good I run a bit hotter but it ain’t going no where

Someone who can weld like this How much does he earn per hour on average?

speed of wire? and voltage?

Pretty good weld man. Makes me grateful too cause mine are starting to look this nice and have always filled well. Good weld

Is that 8.8 wire speed? Damn bruh

💩💩💩💩💩💩

Would often do down hill for the first pass, but always vertical up weave to finish

It's not the strongest of techniques, more just for speed

Yeah nah... Throw a root run in first, then twist your wrist for the capping, pause on the toe for a second or two, move rapidly but smoothly to the other side, direct and pause on the toe... Stops build up in the guts, but you know you've got the pen from the first root so now it's about building it up, adding more meat to the table.

Good job What is the make and model of mig welding machine used

In this shortcut , you should mention that you used a pulse mod, that's way voltage went so high,

Got to love spray transfer. Super smooth arc and nice and quite

It's nice to show it but why not explain it too, you can also just step and get a very similar effect just watch where you step from and go back to it

А это насколько сильно ?! На сколько килограм сильная сварка будет?!

😂🤣👍 einstellung zeigen und dann superpuls 😂😂😂 und keiner merkt 😂😂😂

Как такое

turn wire up a tad 🔄

I was taught not to let the outer shield to never touch metal??? Depends on how good the metal is whether u weave it or not. Softer steel like Canadian I whip it and move on

I was taught not to let the outer shield to never touch metal??? Depends on how good the metal is whether u weave it or not. Softer steel like Canadian I whip it and move on

not really secret, its beginner welding.

Too much wire... push de pulse up. Dont do forward stop , do forward back. Try and tell me the results

It’s terrible bro that’s why. Jus go slow nd consistent on flat bro or step in nd out

Vol? Amp?

❤

8/10

🙏 RK steel works for 💯 subscribers.

You didn’t explain how many amperage and voltages use

Thats the sound!😊

If you drag you let all the dirt down in the weld .....

Звук как ММА

Too pushing angle

Nice weld pitch

bro why ntf u fighting the base metal damn

Шляпа какая то😂👎

Downward certainly has its uses despite what some of these comments say; however, the only acceptable thing here is the technique. The joint configuration, without prep work, on this material thickness, not recommended. Even with prep on thicker material I’d rather use another process. Neither the base synergic setting or the adjusted setting where acceptable, the base was way too low in addition to the adjusted setting. Downward progression is good for open root welds (root pass only), and sheet metal fabrication, especially on certain joints, like open corner or inverted corner joint (fillet weld). It’s good for filling gaps, and architectural fabrication as well. So says my experience and education at least.

Я никогда не делал зазоры проще фаски снимал с металла и всё.... И всё под рентген уходило

So you just lay a standard fillet weld, wow big secret that only a few people know. Stop your click bait titles.

Try pulse on pulse aluminum 4G.

If you clean the weld area a little better you can get that to run without the crackling of impurities burning off. But it’s probably not necessary. Pulse welding is great ❤

Should point the gun opposite angle😢

Nice. Good job

Why pull not push?

Let me do a shitty weld and show you a different weld.

i think your wire speed is too high its popping like popcorn you might consider to lowert it down

This is bad bro. To low amps and volts, and u went to fast for your settings thats why your weld is curve. It need to be flat. No garb at all.

Jyada spatters h

Good looking weld

😢