3 жыл бұрын
Пікірлер
@LJay-pv8lm Күн бұрын
Omg you make that look so easy 😭
@Shahrezad1 4 күн бұрын
May I ask what type of metal the pin section is made of? I would like to do something similar to this, but (as a beginner) I'm not sure if my Tin solder will attach to certain new metals.
@marybulanova_jewelry 4 күн бұрын
I am not quite sure, but I think it's some kind of steel. It's definitely not stainless steel.
@danielchudy8234 18 күн бұрын
Hello, do you use a mask when doing this? Are the fumes dangerous?
@marybulanova_jewelry 18 күн бұрын
Hello, no, I don't use mask. Just opened window. My solder is lead free. That's why it's not so dangerous.
@sonowwhat5682 22 күн бұрын
How did you get the hole in the china?
@marybulanova_jewelry 22 күн бұрын
I used a diamond drill.
@ShameemKhan-nl9iv 25 күн бұрын
Hi
@evabrauer4044 Ай бұрын
What do you Use to seal or proect the Tin from reacting with oxygen?
@marybulanova_jewelry Ай бұрын
Nothing. I don't see the point. After patination and careful polishing, tin retains its shine for a long time. If it becomes dull or dark, it is enough to rub it with a rough cloth. And the shine will return.
@christywinkleman9830 2 ай бұрын
How do you keep them from falling off? I clean, Flux. I can make the balls but they fall off.
@marybulanova_jewelry 2 ай бұрын
The place where you put the balls must be hot. You have to warm it before placing the balls.
@Musicfan_CH 2 ай бұрын
This is not how you should do it
@mariejerechinska137 2 ай бұрын
great video! what is the liquid used to clean jewellery at the end please?
@marybulanova_jewelry 2 ай бұрын
Thank you! It is not for cleaning. It is patina. Then I polished the ring with steel wool. But I didn't film the moment.
@mariejerechinska137 2 ай бұрын
@@marybulanova_jewelry THANK YOU SO MUCH
@Rapscallioness 2 ай бұрын
What is that liquid used to attach the tho pieces together?
@marybulanova_jewelry 2 ай бұрын
It is written on the bottle Soldering Axid. I solder with leed free tin solder.
@Rapscallioness 2 ай бұрын
@@marybulanova_jewelry thank you 🫶
@afrobluatlanta2380 3 ай бұрын
Short but sweet. Thanks!
@cc1983x 3 ай бұрын
These are really cool! I was wondering what are you using to solder the pieces of metal? I have tried a few times but no luck with no lead . I tried a silver and copper solider wire, with butane and solder but still broke when I was filing after pickel in vintager and salt. I'm trying to learn . Thank you 😊
@МаракуЙя-г5ю 4 ай бұрын
Подскажите, а что вы наносите кисточкой? Это порошковый флюс?
@marybulanova_jewelry 4 ай бұрын
Нет, не порошковый. Обычная паяльная кислота.
@cmevans 5 ай бұрын
This is the first video I've watched for TTSS. Extremely helpful, thank you!!
@marybulanova_jewelry 5 ай бұрын
Thank you!
@tinkers21 6 ай бұрын
What is the wire?
@marybulanova_jewelry 6 ай бұрын
Steel.
@RaymondWise-yq9by 7 ай бұрын
Beautiful and gorgeous and brass ring
@patriciakendall6494 9 ай бұрын
Oh wow I didn’t know we could tin over steel…thought it was only tin over copper …good to know. Thank you
@marybulanova_jewelry 9 ай бұрын
I use zink plated steel. But some craftsmen even solder stainless steel. But it more difficult.
@mischievousmoon1004 9 ай бұрын
How do you create the dots if I may ask? All I keep creating are spikes lol
@marybulanova_jewelry 9 ай бұрын
I can't explain. Just as in video:). Flux, solder and iron.
@ThePose78 5 ай бұрын
@@marybulanova_jewelryso can you say if that’s flux you keep tapping with the brush?
@marybulanova_jewelry 5 ай бұрын
@@ThePose78 Yes, it is flux.
@kolbasyonok5898 10 ай бұрын
Thank you so much, its literally first video where I found which flux exactly I can use 😇🙏 паяльная кислота 😊 everyrhing was that simple
@marybulanova_jewelry 10 ай бұрын
❤❤❤
@jessnotfound695 10 ай бұрын
what are you putting with that brush?
@marybulanova_jewelry 10 ай бұрын
Flux
@mjremy2605 11 ай бұрын
What is the purpose of this video? To sell your jewelry? To show what you made? Most channels have instruction on how it is made. You show nothing.
@RaraAvis1138 Жыл бұрын
It's those little details that makes your art so lovely. I want to make things from copper and found objects very much.
@RaraAvis1138 Жыл бұрын
Im crying! This fills me with such joy its so beautiful and speaks to my soul❤
@debbieabbott5503 Жыл бұрын
Gorgeous love it ❤
@marybulanova.uniquehandmad7511 Жыл бұрын
Thank you!
@debbieabbott5503 Жыл бұрын
I've been searching on KZbin for hours looking for something beautiful unique 👌 I want to make one myself? Thank you for sharing its absolutely perfect its beautiful I love it alot more than any I've seen ❤.
@marybulanova.uniquehandmad7511 Жыл бұрын
Thank you so much for your kind words. I do not add new videos here. All my new videos and new works are here youtube.com/@marybulanova_jewelry
@jademckay-robinson8447 Жыл бұрын
You make really beautiful pieces!! Keep it up! ☺️👌🏽✨🙏🏽🌹🔮
@marybulanova.uniquehandmad7511 Жыл бұрын
Thank you so much!
@bubblefizz9144 Жыл бұрын
Ohh beautiful 😍 how do you harden the copper back up when you have soldered? I tried something similar to this, but my leaf was to soft and I couldn't hammer it with a stone on it ?
@marybulanova.uniquehandmad7511 Жыл бұрын
Thank you! I tapped the leaf with a rubber mallet. You can also stamp the streaks after soldering, not before it. but may be my copper sheet is just a little bit thicker than yours.
@bambie7376 Жыл бұрын
Beautiful
@claidis Жыл бұрын
Love this
@marybulanova.uniquehandmad7511 Жыл бұрын
Thank you!
@moevann3124 Жыл бұрын
Worth the effort they are great!
@moevann3124 Жыл бұрын
Hello, I was wondering what kind of grinder do you use? Thanks for the video!
@marybulanova.uniquehandmad7511 Жыл бұрын
Thank you. Some cheap household item. BauMaster BG 6012X.
@jazzyjewels2034 Жыл бұрын
I wanna make more DIY jewelries like this. I hope I can! ✌
@marybulanova.uniquehandmad7511 Жыл бұрын
Good luck!
@jazzyjewels2034 2 жыл бұрын
This was such a amazing video!!! 😃👍
@marybulanova.uniquehandmad7511 2 жыл бұрын
Thank you!
@jazzyjewels2034 2 жыл бұрын
This was such a amazing video!!! 😃👍
@marybulanova.uniquehandmad7511 2 жыл бұрын
Thank you!
@jazzyjewels2034 2 жыл бұрын
Awesome design👌👌👌 you have made😊
@marybulanova_jewelry 2 жыл бұрын
Thank you so much!
@TheHappyHomesteadingHerbalist 2 жыл бұрын
I need a slower tutorial on making the dots. Just can't seem to do them. Lovely ring. Thanks for the video.
@tammymiller4499 2 жыл бұрын
What kind of wire are you using for the ear-wires?
@tammymiller4499 2 жыл бұрын
What kind of wire are you using for the ear-wires?
@marybulanova_jewelry 2 жыл бұрын
Here I used brass wire. But usually I use zinc coated steel wire.
@earthtozaya468 2 жыл бұрын
Thanks for the video!! Can I ask what temperature you keep your iron at? I am trying to find the sweet spot that keeps the metal melting smoothly without burning the tip of the iron. Also, how do you clean your peice after? I find I always have a sticky residue from the Flux that I'm not sure how to clean. Thanks in advance
@marybulanova.uniquehandmad7511 2 жыл бұрын
Thank you for your comment:). I am not sure about the temperature. My iron is 100 watt, that's all what I know about it. I clean my peaces with some shampoo or dishwashing detergent. Before I sometimes used ultrasinic cleaner, but it was cheap and broke down soon. But there is no great difference with shampoos. Pieces are not sticky if you wash them thoroughly with a tooth brush.
@earthtozaya468 2 жыл бұрын
@@marybulanova.uniquehandmad7511 thank you so much for your reply!!
@pinkfoxthenoob 2 жыл бұрын
Looks cute!
@marybulanova.uniquehandmad7511 2 жыл бұрын
Thank you!
@svet_lana... 2 жыл бұрын
Русский акцент)))
@maya3334 2 жыл бұрын
Looks gorgeous!
@marybulanova.uniquehandmad7511 2 жыл бұрын
Thank you!
@BlackpearlAbu 2 жыл бұрын
Wow!!!!
@BlackpearlAbu 2 жыл бұрын
Awesome
@marybulanova_jewelry 2 жыл бұрын
Thank you!
@BlackpearlAbu 2 жыл бұрын
Nice gorgeous ring !!!
@marybulanova_jewelry 2 жыл бұрын
Thank you!
@fairdinkum1079 2 жыл бұрын
Absolutely stunning What wire and solder do you use please
@marybulanova.uniquehandmad7511 2 жыл бұрын
Thank you! Steel wire and lead free solder. I made photos for you, but I am afraid I can't add them here.
@marybulanova.uniquehandmad7511 2 жыл бұрын
The solder is Felder. Made in Germany. I used some China one with a flux core. They say it is bad, but I didn't notice great difference.
@marybulanova.uniquehandmad7511 2 жыл бұрын
Check this video kzbin.info/www/bejne/b3nbZYuch9Wrm6s . I show my solder there. Second 56.
@fairdinkum1079 2 жыл бұрын
@@marybulanova.uniquehandmad7511 thank you
@fairdinkum1079 2 жыл бұрын
@@marybulanova.uniquehandmad7511 thank you Will watch now
@tishsmiddy71 2 жыл бұрын
Thank you ☺️
@marybulanova.uniquehandmad7511 2 жыл бұрын
😊
@irenartcreativeiralu7432 2 жыл бұрын
Lovely❤️🌸 can you tell me what kind of soldiering machine you are using?
@KarenMinaK 2 жыл бұрын
😍😍😍😍 what's the metal? and what is its thickness please?😍😍
@MariaHernandez-rs7qj 2 жыл бұрын
Look so easy! What gauge?
@marybulanova.uniquehandmad7511 2 жыл бұрын
I am sorry, I don't know. It's 0,5 mm.