3 ай бұрын
Жыл бұрын
Жыл бұрын
2 жыл бұрын
3 жыл бұрын
3 жыл бұрын
3 жыл бұрын
Пікірлер
@willy077412 9 сағат бұрын
Hi why you change both? The p0011 it's not on right side? Thanks for answering
@TrailRunnerGuy 8 сағат бұрын
Good question. It’s generally recommended to change both left and right camshaft sensors at the same time. They often fail around the same time. And even better to do the crankshaft sensor while in there too. My P0011 (cam, Bank 1 - right/passenger side was finally resolved for good about a week ago). Aftermarket sensors are truly not reliable and I’ll be switching them all out to Hitachi (all 3, before doing any longer trip). Don’t want to be stranded. 🤘🏻
@willy077412 8 сағат бұрын
@@TrailRunnerGuy Oh perfect, thanks! I will do the same!
@richardlemaire5895 13 күн бұрын
He's gonna leek again ! Put silicon anywere or dont'put anymore !
@TrailRunnerGuy 13 күн бұрын
It’s been good so far! We’ll see how long it lasts. 🙂
@timwinkler2337 15 күн бұрын
Great video sir, thank you!
@TrailRunnerGuy 15 күн бұрын
You bet! Thanks for watching!
@oldsoul_oner 17 күн бұрын
when you gut the square with the grinder, would it be necessary to apply some sort of anti rust to the raw metal? Just wondering because im considering doing this
@TrailRunnerGuy 17 күн бұрын
Yes - I’d say “highly recommended.”Anything to protect that raw metal would be ideal. I didn’t do it only because it rains 3 times a year in Arizona. 😄
@jmar3011 26 күн бұрын
You’ll always get coil bucket contact going the cheap spacer route. Best thing is to go with extended travel coilovers.
@TrailRunnerGuy 26 күн бұрын
For sure. If I were to do it again I’d either go high end ones or just Titan swap the whole front suspension.
@TrailRunnerGuy Ай бұрын
Full install video coming soon! And I may not lose my thumbnail! 🤞🏻🏆
@backwoodsifywithmac7143 Ай бұрын
Thank you so much. I was hoping that i wouldnt have to tear the whole dash out. Straight to the point. You got my sub friend.
@TrailRunnerGuy Ай бұрын
Thank you! And glad it was insightful. Cheers! 🍻
@obxarms7685 2 ай бұрын
Nice job!
@TrailRunnerGuy 2 ай бұрын
Hey, thanks!
@PaulHenreid 2 ай бұрын
My 07 Xterra has a leak in the valve cover gasket passenger side rear corner. I did not know the valve cover gaskets are different. Why do you think it leaked?
@TrailRunnerGuy 2 ай бұрын
That passenger side rear corner valve cover gasket has always been a problem on mine. It’s much better now with a rare drip vs a prior flow. I’m not sure but I think I overtightened the bolts. Next time I will torque them properly.
@CALISUPERSPORT 3 ай бұрын
Rotten luck, but the 2003 models don't have the connector at the switch. You gotta disassemble everything above it in the engine bay in order to take it off. And since you're buying the part with the harness attached, it's also more expensive.
@TrailRunnerGuy 3 ай бұрын
Bummer. And thanks for including that here for others! 🍻
@terra4.0 3 ай бұрын
Nice video.. i live in az hope one day we can go on some trails
@TrailRunnerGuy 3 ай бұрын
Thanks! Always great when we can get off the pavement!
@porraspris12 3 ай бұрын
We couldn't get the rotor back on
@TrailRunnerGuy 2 ай бұрын
Late reply, but did you manage to get it back on? Sometimes it takes a little effort.
@alexandercahoulan6583 3 ай бұрын
Oh great…a Nissan
@SaldecoAB 3 ай бұрын
Boil it in water ,
@HeadbangMushroom 3 ай бұрын
Try silicone spray
@ib1424 3 ай бұрын
Remove/loosen the clamp 🤦♂️
@TrailRunnerGuy 3 ай бұрын
It was so loose it was almost falling off.
@jeremyswingle4752 3 ай бұрын
Hmm don't fucker dry add lube 😅
@TrailRunnerGuy 3 ай бұрын
Anyone else? 😂
@phoenixleaf2324 3 ай бұрын
It's gotta get on sometime😂
@TrailRunnerGuy 3 ай бұрын
@phoenixleaf2324 Indeed. After some soap! 🤣
@colinstickland3130 3 ай бұрын
@@TrailRunnerGuyI would have used vaseline.
@texaszygote7956 4 ай бұрын
Don't be scared of that spring bro. It won't go far...
@TrailRunnerGuy 4 ай бұрын
Ha. I’ve seen videos. And I don’t wanna be “that guy.” 😄
@MrKredinger 6 ай бұрын
This help me, thank you
@TrailRunnerGuy 6 ай бұрын
Glad it was helpful!
@ethanoltean 7 ай бұрын
How long did this take you?
@TrailRunnerGuy 7 ай бұрын
Start to finish roughly 3 hours with some beverage breaks. An hour of that was just deciding/completing how/where I wanted my winch wiring and cut-off switch.
@jaybuilder8298 4 күн бұрын
Where did you get that?
@TrailRunnerGuy 4 күн бұрын
The bumper mount: wambumpers.com/ The winch: Amazon. I think I linked to it. If not I’ll add the link to the description shortly.
@devinbarry1136 8 ай бұрын
Pure gold
@TrailRunnerGuy 8 ай бұрын
Thx Devin!
@theboz322 8 ай бұрын
That specific vehicle will need it...often...
@TrailRunnerGuy 8 ай бұрын
Haha. 186,000 miles and counting!
@BinALA 7 ай бұрын
What do you mean?
@TWMarx-vm1ms 8 ай бұрын
I have a Kia Sorento 2019 that has this problem. 40k miles on it, and the driver front assembly needs replacement, but the passenger seems to corroded so will need replacement as well. My question to you is, what if any torque settings are there for this replacement? If so, what tool would you best recommend for this job? Thank you in advance.
@TrailRunnerGuy 8 ай бұрын
Yours is 8 years newer than mine was so not sure on torque #. (I no longer have it). The FSMs can be found here and spec #s included. www.ksmanual.com/kia_sorento_xm_2011_year_service_manual-195.html If you are replacing the strut yet, keeping your existing springs, I recommend any sort of spring compressor tool with the 3-piece clamps. Much safer than 2-piece. If I can find the one I have I’ll post it below.
@TrailRunnerGuy 8 ай бұрын
Found them. a.co/d/hW33CYG Says no longer available, but something like this.
@TWMarx-vm1ms 8 ай бұрын
@@TrailRunnerGuy thank you very much. Yes I will be replacing the whole assembly. Even the the spring might be in good order, it's just easier, faster and safer to replace the whole assembly, without compressing any springs. I found a set for under 300#
@f5fstop 8 ай бұрын
Did you really have to remove the spindle from the UCA to replace the shock/coil assembly? On my 2023 Frontier it is not necessary.
@TrailRunnerGuy 8 ай бұрын
I’ve heard for many it’s not required. It was a very tight fit on mine so just went that route.
@orlandosantiago3304 8 ай бұрын
Were you buy it?
@TrailRunnerGuy 8 ай бұрын
wambumpers.com/
@unclefreddieDied 9 ай бұрын
So you don't need that bleeder nipple thing?
@TrailRunnerGuy 9 ай бұрын
Never used it in 3 or 4 air bleeds (new radiator, timing stuff replacement, etc.). Was always afraid to touch it. Good thing I never did. 😄 Just always burped it, revved the engine a few times, squeezed the big hoses, etc. and never had an issue.
@tedphillips7727 10 ай бұрын
TrailRunnerGuy: I just put on my WAM winch bumper and an OFFROAD 13K Winch. I bet it squatted about 3/4" on the front end. I have oem springs and 5100 Bilstein's on the 3rd setting. Not the highest lift but next to it. So I get to adjust my spring position to the highest position to gain back the way it was sitting. Thanks for sharing your bumper instaall it helped alot. I cut off about 2" below the top of the bottom section of bumper to create a nice hole for the winch access. The opening is about 1/2" below the bottom of the winch. That is as close as I could guess on location. But it turned out well. Thanks again.
@TrailRunnerGuy 10 ай бұрын
Right on - glad it worked out! I’m sure your bumper trimming was 10x better than my hack job too! Careful adjusting it to the highest setting though. Your up-travel will be next to nothing and likely harsh (at least mine was). I moved it back to the middle setting.
@ricardoroman6834 11 ай бұрын
Does it fit to lift frontiers pro 4x models 2018 models?
@TrailRunnerGuy 11 ай бұрын
For 0-2” lifts yes. I’d verify wherever you’re shopping however, everything I’ve seen says they are also compatible on Frontiers up to 2019. Check All Dogs Offroad, for example.
@straightcheez2892 11 ай бұрын
Awesome
@jensimpl 11 ай бұрын
Nice job! I'm thinking to do the exact same setup as you have. Do you have any comments on the winch you installed? Are you happy with the Rugcel?
@TrailRunnerGuy 11 ай бұрын
Thanks! Haven’t had to pull anything heavy/difficult with the winch yet (just a couple easy, short pulls) but so far, it’s great. Cut-off switch and wireless remote work great. No issues.
@Mary_Ruiz_93 11 ай бұрын
I really appreciate you making this video! Now I know I can do this myself 😊
@TrailRunnerGuy 11 ай бұрын
Glad I could help! Yes - it’s not too bad!
@beardumaw24 Жыл бұрын
The 5100s are a great shock if set up right. Don't preload them all the way, ie don't adjust them to the highest lift setting that limits the shock travel and flex and makes them ride worse. Leave them on the lowest lift setting so they keep their shock travel and add a lift spacer on top of your coilovers to add vehicle lift and you will keep all the travel the 5100s have and keep good flex and ride.
@TrailRunnerGuy Жыл бұрын
Couldn’t agree more. Through trial and error I still landed on the middle setting to keep my ride height where I wanted it. And the fact that I rarely get off the pavement for any serious terrain. Need to change that!
@irwinjimenez Жыл бұрын
It's actually doesn't look bad.
@TrailRunnerGuy Жыл бұрын
Appreciate it- the hack job has kinda grown on me. I’ll leave it for now. 😄
@TrailRunnerGuy Жыл бұрын
Chinesium quality… 🫤
@devinbarry1136 Жыл бұрын
Way louder! And yes, another master piece
@TrailRunnerGuy Жыл бұрын
I think you need one for Christmas! I’ll help you install it!
@harveydanger8282 Жыл бұрын
Did winch fit OK? or did you have to modify? Thanks for nice video!
@TrailRunnerGuy Жыл бұрын
Winch fit very well. Trimmed a small amt of the center plastic opening to easier reach the winch controller plug. Might install my Hornblasters “mini” horn this weekend. If I do I’ll show some closeups of the winch area too.
@thecount1001 Жыл бұрын
what's your thoughts on skipping that replacement coupler altogether and just connecting the hose directly to the core outlet fitting? problematic?
@TrailRunnerGuy Жыл бұрын
I know people have done it. Heard of a roadside fix doing that a time or two as well. If it doesn’t leak and doesn’t pull the hose too much I don’t see why it wouldn’t work long term too.
@daniellore2961 Жыл бұрын
Low oil pressure is oil channel gaskets broken. They are behind the timing chain. My condolences to you.
@TrailRunnerGuy Жыл бұрын
All 2005 Xterras and early 2006s have a live oil pressure gauge (instead of a dummy gauge which just sits in the middle). What you’re seeing here is 100% normal. All timing components including channel gaskets were replaced by me a couple years ago - should outlast the vehicle. 🤞🏻
@daniellore2961 Жыл бұрын
@@TrailRunnerGuy ok, thats great to hear. Unfortunately my oil channel gaskets did not get changed when the timing chain was changed. I assumed that was the case for you. My apologies.
@TrailRunnerGuy Жыл бұрын
@@daniellore2961 all good! Sorry to hear that. Opening that thing back up is a total pain (I’ve opened it twice…try #1 was one tooth off. Major oops! 🤣)
@daniellore2961 Жыл бұрын
@@TrailRunnerGuy yea, its going to be a pain. I'm considering swapping in an ls v8. As good of an engine as the 4.0 is it is a mess to work on. I wouls rather have old school in the nissan package. I'm still thinking on it though. It will be a challenge.
@daniellore2961 Жыл бұрын
@@TrailRunnerGuy I just realized that the ls has an oil channel gasket behind the cam retiner plate. Can't get away from it.
@gr1f1th Жыл бұрын
just replaced mine this weekend, plastic broke in the same place. I got the hose section replaced too because I was there.
@TrailRunnerGuy Жыл бұрын
Good call. Can’t believe how brittle those things are! Easy fix to avoid a catastrophe!
@devinbarry1136 Жыл бұрын
Love this guy! He can fix anything
@TrailRunnerGuy Жыл бұрын
Ha. Thx D!
@TrailRunnerGuy Жыл бұрын
Who’s had one fail on the road?’ 🙋🏻♂️
@neoskater420 3 ай бұрын
Just did it today on a 2017 4x4 frontier whole I'm yelling cheap plastic even my 83 89 broncos I had was metal/aluminum if they got it rght in back than why cheap out to plastic. Everything is getting replaced now heater inlet from z1, valve covers also I'm going to swap out radiator I'm find full aluminum one no plastic is aloud at all. Was stuck in the desert an hour from any auto store had to drive stop cool down drive til I got a friend to come give me a ride by passed the heater core as well so dumb of an idea to make these plastic@!!!
@TrailRunnerGuy 3 ай бұрын
@@neoskater420 dang! Good work getting back to civilization / getting it fixed!
@Abdultomat753 Жыл бұрын
Did you ever had an issue about the vdc and slip off light on the xterra . Nice vid btw.
@TrailRunnerGuy Жыл бұрын
Thanks. No slip / VDC light issues for me so far.
@Abdultomat753 Жыл бұрын
@@TrailRunnerGuy thanks you 👍👍👍👍
@elcompamartinez2647 Жыл бұрын
I finnaly instaled this lights are great....i put a iltle plate welded to that tubular 2x2 (part of the hitch bar) since i keep my truck as originaal as posible .....but my signals are blinking fast and no bad bulbs ....any ideas?? this always happens?
@TrailRunnerGuy Жыл бұрын
Right on. While the fast blinking turn signals is usually a burned out or just faulty bulb I’d check that any new wiring is not touching any metal? Fast blinkers are usually a change in resistance, so there could be a short somewhere.
@joshua_patterson Жыл бұрын
This is a great idea. I need to do this. Thanks!
@TrailRunnerGuy Жыл бұрын
I don’t miss that dang prop rod!
@devinbarry1136 Жыл бұрын
Another masterpiece!
@TrailRunnerGuy Жыл бұрын
Ha! Not so sure about that, but thanks, Devin! 🤣
@_moes_garage_ Жыл бұрын
Nice video man! I'll have to replace mine before it goes out.
@TrailRunnerGuy Жыл бұрын
Thanks! Yes, I was probably playing with fire driving with it as long as I did!
@jvh22a Жыл бұрын
Mine broke to. Then i crushed the core inlet. So i had to replace the heater core. Such a pain but i love my xterra.
@TrailRunnerGuy Жыл бұрын
Bummer! Not gonna lie - I was a tad nervous taking it off and really hoping I didn’t cause 10x more work by damaging it.
@jayanderson6016 Жыл бұрын
Rear caliper mounting brackets are 76 ft lbs / front 136 ft lbs.
@TrailRunnerGuy Жыл бұрын
Excellent - thanks for sharing that!
@tedphillips7727 Жыл бұрын
Hello Nice video. I noticed your hood has gas springs. Did you add those yourself or did they come standard? I have a 2006 and it has a crappy stick to hold up the hood. If they are standard let me know you vehicle year so i can go find some "replacement units and I will stick them on my hood. Thanks. Im gonna get a WAM when i gert ready to add my winch. I love how it tucks under and is compact. Thanks.
@TrailRunnerGuy Жыл бұрын
Thanks - I love my hood struts! This vid has the link to the one I purchased. Hood Struts Upgrade on the Nissan Xterra. For Frontier and Pathfinder too. kzbin.info/www/bejne/i5uXn4qcZr90gJY