How do you have a dual recoil spring? I just picked one up and had to buy a single spring kind of like the Glock, but mine is an sig oem spring for the x macro.

Nice walkthrough and thoughts. I’m trying to decide on this or a reset magazine.

I’m with you brother 😂 I got my Bailey 3 gun foreend December 2023. The instructions make it seem very easy to install. Wrong! It took about an hour to install. I did not remove the two pieces that you did. It is very tricky getting the barrel aligned on the bolt carrier. After several tries everything fell into place and the barrel and forend slid into place. I’m not sure if you noticed, there is a rubber spacer where the mag tube hole is at the top that you removed. The spacer fell off and did I did not notice it until I got everything assembled and notice there was a little movement. So you guessed it, I had to remove the foreend and barrel again😂. It appears to have had some type of adhesive that obviously failed . When you get a chance please redo another install video. Thanks.

Thank you. I want to get this kit, but it seems a little pricey for what you get.

Did you notice increased felt recoil with this frame?

Can you make me grips for the 60ds bb revolver? I dropped the revolver and the grips broke.

Thank God for this video because I would’ve never figured out how to use this damn thing

Thats the one thing that bugs me about my p320. The reset on the trigger just isnt the greatest. Ill likely grab one of these to try now. Thank you!

Sig includes these now no charge.

So I had purchased the same barrel 6 months ago as a secondary for my spectre comp. I recently installed it and it is very tight in the slide it’s hard to rack and won’t always go into battery. But I have no shot it yet I’ve read it will break in. Have you experienced any of this?

For what it is worth... This mod worked very well for me . Found a an Advantage Arms 22 LR conversion kit for a Gen 3 Glock 17. I did exactly what the video says in terms of parts polishing. In addition I noticed the feed ramp on the barrel had a burr on it near the bottom. Removed it and polished the feed ramp. First try at the range it worked and worked wonderfully. I started with CGI 40 Grain Round nose exactly what Advantage Arms suggested. No problems. Much to my surprise it also shot Federal Copper Plated Hollow points. No problems. I can't say for other types of ammo as those are the only two 22 LR loads I had. Thanks for the advice in the video. The "Eat Anything" mod worked for me.

Doesent look like either one is any good , there must be a better alternative !!

I had another thing I was curious about advantage arms says not to run hollow points. Is there anything you can do specifically that will help you run hollow points? Just curious cause I have tons of Remington golden hollow points.

FAIL = First Attempt In Learning 👍

Thanks nice video

The fast-forward sequence is highly entertaining with you Alvin & the Chipmunks voice! 😂

Very interesting video, I learned lots about this firearm from the comprehensive way you broke things down. At a buck a shot, this is a budget-breaker for me. 😀

Also in Pa... thank you for this video brother.

Both of my screws on the stock optics ready plate on my Sig P365 x macro comp completely stripped when I tried to remove it with a torx T10. I picked up the set you recommend in your video and after applying some heat from a heat gun I was able to remove both stripped screws and install my red dot. Thank you for the great video and tool link!

Another person with a long video and does nothing but talk.

Had the same issue! Was using a dove mount for my Glock, which they use 5/32 tiny screw which strips! Your awesome 👍🏽 thanks

So does the ejector have a roll pin? If you punch it out can you reuse the same pin? I see on their site. They have a replacement kit that includes a new pin,,, I wanted to polish it, but I’m afraid of damaging the pin

Seems strange they haven’t made an FDE version. Usually when I think of staking it means actually physically staking in the screw. This is more of just marking their position.

So do I need a torque limiter? I do not have one. Just ordered my 19 and have my scs sight already. I’m new to this and wanna make sure I’m okay

I'm pretty upset over these mag conversions. I tried these and ran about 200 rounds through them with no problem. Lead, FMJ and JHP, no problem. I went out last weekend and the hollow point scoops into the bottom of the feed ramp, damaging the feed ramp and 100% hanging up after each shot. That means these mags are range toys, not for serious or defensive use.

Does it telescope? Can mod2 work with adapter too?

Worst trigger review I have ever seen. What an amazing waste of my time. You are missing every single thing that a good trigger review needs. Crazy.

It’s on sale for 60$ gonna get . I need something that will work for my only ar snd money is tight . It’s not like I’ve ever needed my rifle . As long as it’s good enough

Pretty neat.

Just got and noticed that the inside piece is hard to get back into the barrel to extractor - does it need some lube to pop back in seems tight

How does that trigger do with 762 ? Any LPS

Now you tell me. I've chewed the crap out of mine. Just got the gun. Haven't even fired it yet. Took it apart to clean and chewed the crap out of it. Getting ready to order a new one. Perhaps one of those cool barrel-shaped aftermarket models

How much time does it need to dry before wiping off between coats? #diynationth

tanks for not showing putting in the screws. There are three different lengths of screws. Which goes where. Wasted video

Trying to source the right tools for the job, starting to regret buying this firearm that requires so much effort just to get it to function properly. Cmon Stoeger…

How funny, the next video says the myths of over lubrication.

Thanks for the PSA

Exact review I was looking for hope you do reach the audience you desire

Does your slide have more of a gap towards the front . Just got one was wondering if that was normal

I've run about 500 rounds through mine and it was been very consistent. I like it better than the ALG ACT and the BCM nickel boron trigger

Appreciate the review - made me pause a bit before purchasing this.

Thanks. My tritium is out

Very well explained. Thanks👍 nice watch👍

Damit this is harder than it looks. I have a Canik Rival SFX and I'm having issues.

I know this is old and surely you figured this out by now but you're absolutely using that wrong!!!! Haha the handle at the top that you set is where the torque gage is, their site, hundreds of reviewers, other videos, etc. are EVERYWHERE showing the proper use of these Haha you're just turning a screwdriver the way your using em, a VERY expensive screwdriver at that Lol

Just what I was looking for. Thank you!!!

Look how thin and light that is! That's a scam! It's a toy!

This dove dot product is amazing. i have had for many months and still holds zero no movement on my glock 43x. great and only product i would use in a dovetail..very secure

What do you think about Hawg holsters?

ETS is shit magpul never loses though