मेरी तो बन ही है बस हवा मे छोड़ ना है 🎉🎉

😊😅😮😮😢

,🤩🤩🤩🤩🤩🤩🤩🤩🤩

Abang. Coba. Tutorial. Buat. Wau. Barat 😢

অসাধারণ ❣️👍

Mantap bossqu. Tetap semangat berkarya 👍👍👍👍

Alhamdulillah klok layangan ini terbang 😂😂😂😢

Very good 👍🏼

মত জজ রকম 😮

()

Simple but terrible

next konten coba buat layangan papiran dong bang

Hasilnya bisa terbang lentur" Gimana kalo di terbangun

❤❤❤

thank you bro❤😊🦸

Super very beautiful ❤🎉

Bang izin buat ya bang 🙏❤

WOW 🥰

😊𝚝𝚞😊

😮😮😮😂😅😂😊

Pertama. Bang

Please layangan yang Pegon buat aku dong please

Mantap

good

Layangan berek

Bagus, Aku Mau dong bang Minta!

Mantap

𝖠𝗄𝗎𝗆𝖺𝗎 𝑑𝑜𝑛𝑔𝑏𝑎𝑛𝑔

Hi

Bang aku minta layangan ya dong 🙏🙏🙏🙏🙏🙏

এই গুরির নাম কি

Wau,maharaja,Mie,semua,pakai,buluh,

হ

13:43😊😊😊

Gimana cara buat banh

बहुत सुंदर पतंग बनाई गई है 👍🏼

Kecil Sekali

mirip layangan aang avatar

Hay quá ha

🥰🥰🥰🥰😘😘🎉👌

Selalu ada layangan bau wow!!!

❤❤❤❤❤❤

### Tools needed: - Small knife - Scissors - Hot glue gun - Marker ### Media needed: - Two wooden dowels (one 40 inches/100 cm, one 34 inches/85 cm) - String - Garbage bag or thin plastic sheet ### Steps: 1. Cut one dowel to 34 inches (85 cm). 2. Lay the 40-inch dowel flat. 3. Place the 34-inch dowel on top, 4 inches (10 cm) above the midpoint, perpendicular to the first dowel. 4. Wrap string around the intersection and hot glue to secure. Let dry. 5. Cut a notch in each dowel end. 6. Run string around the dowel ends, using the notches to hold it in place. Pull taut and tie. 7. Cut off excess string. 8. Lay the frame on a garbage bag or plastic sheet. Outline with a marker. 9. Cut the plastic, adding 2 inches (5 cm) around the outline. 10. Glue the frame to the plastic. Fold the excess plastic over the dowels and press into the glue. 11. Tie a piece of string to each dowel end and connect them with a third string at the intersection for the bridle.

### Tools needed: - Small knife - Scissors - Hot glue gun - Marker ### Media needed: - Two wooden dowels (less than 2 inches/5 cm in diameter, one 40 inches/100 cm long, the other 34 inches/85 cm long) - String - Garbage bag or sheet of thin plastic ### Steps: 1. Cut one of the wooden dowels to be about 34 inches (85 cm) long. 2. Lay the longer dowel (40 inches/100 cm) on a flat surface. 3. Place the shorter dowel (34 inches/85 cm) on top of the longer one, about 4 inches (10 cm) above the midpoint, so they are perpendicular. 4. Wrap string around the point where the two dowels meet. 5. Use hot glue to cover the string and seal the two dowels together. Wait a few minutes for the hot glue to dry. 6. Cut a notch in the end of each dowel using a small knife. 7. Run a long length of string around the ends of the dowels to connect the four ends, using the notches to keep the string in place. Pull the string taut and tie the ends into a knot. 8. Cut off the excess string with scissors. 9. Lay your frame on top of a garbage bag or sheet of thin plastic and outline the frame with a marker. 10. Set the frame aside and cut around the outline you drew, adding 2 inches (5 cm) to each side as you cut. 11. Lay the frame on top of the sheet you've cut and line the inside of each dowel with hot glue. 12. Fold the excess plastic over the dowel and press it into the hot glue. 13. Tie a piece of string to the end of one of the dowels, run the other end of the string to the opposite end of the dowel, and tie it there. 14. Repeat this process with the other dowel and a second piece of string. 15. Finally, tie the two lengths of string to a third piece of string at the junction where the two strings meet to make your bridle and line.

to make a kite first you'll need two wooden dowels that are less than two inches five centimeters in diameter and about 40 inches 100 centimeters long cut one of the dowels so it's about six inches 15 centimeters shorter than the other one then lay the longer dowel down on a flat surface and place the shorter dowel on top of it about four inches 12.5 centimeters above the midpoint so they're perpendicular wrap string around the point where the two dowels meet and use hot glue to cover the string and seal the two dowels together wait a few minutes for the hot glue to dry next cut a notch in the end of each dowel using a small knife run a long length of string around the ends of the dowels to connect the four ends use the notch as you cut to keep the string in place pull the string so it's taut then tie the two ends into a knot cut off the excess string with scissors now lay your frame on top of a garbage bag or sheet of thin plastic and outline the frame with a marker set the frame aside and cut around the outline you drew adding two inches five centimeters to each side as you cut then lay the frame on top of the sheet you've cut and line the inside of each dowel with hot glue fold the excess plastic over the dowel and press it into the hot glue next tie a piece of string to the end of one of the dowels run the other end of the string to the opposite end of the dowel and tie it there repeat this process with the other dowel and a second piece of string finally tie the two lengths of string to a third piece of string at the junction where the two strings meet to make your brindell and line

এটা কী🙄আঠা

Ani sai

Terimakasih atas tutorialnya izin membuatnya boleh kak❤

Wow

Bang aku mau layangan yang simple dong🥰 biar gampang terbang