I'm ready to do this to my exact motor. I actually have a visible leak from one of my main tilt Cylinder. My only concern is trying to rebuilt the tilt Cylinder in place by removing the pin like you were trying at first. I'm afraid I won't be able to do the job because it's Sandwiched in between the brackets and require to remove the bracket and steering to complete the job. I want to start by removing the pin and trying to work with the Cylinder in place. How sure are you I can rebuild the the Cylinder if I can successfully remove the pin? Any suggestions?
@byronargueta3331Ай бұрын
I'm ready to do this to my exact motor. I actually have a visible leak from one of my main tilt Cylinder. My only concern is trying to rebuilt the tilt Cylinder in place by removing the pin like you were trying at first. I'm afraid I won't be able to do the job because it's Sandwiched in between the brackets and require to remove the bracket and steering to complete the job. I want to start by removing the pin and trying to work with the Cylinder in place. How sure are you I can rebuild the the Cylinder if I can successfully remove the pin? Any suggestions?
@matt98eclipse5 ай бұрын
I have the same exact motor. Anyone know the part number for a new seal??
@catchemmatcham Жыл бұрын
What fluid do u use
@jbkahl Жыл бұрын
kzbin.info/www/bejne/o52yc6mjmL5kaNk
@jbkahl Жыл бұрын
Did you check your fluid level
@ronskibinski9472 Жыл бұрын
This guys needs to stop and hire a professional.
@philbarrows4242 жыл бұрын
Wow What an idiot. Hope you sold the boat and took up knitting instead…
@nickg6412 жыл бұрын
this video is fucking useless
@jameslynch34222 жыл бұрын
Well why don’t one of you guys show a damn video of how to do it!
@TX_Nupe2 жыл бұрын
Was the trim fluid leaking? If so where was it leaking?
@caseycarver32722 жыл бұрын
That pin is called a trilobe pin and it’s made to shear off when you drive the larger tilt rod pin out. You don’t reuse trilobe pins. Just let it shear off then clean the pieces out of the pin, etc to drive a new trilogy pin in.
@matt98eclipse5 ай бұрын
I have same motor 96 mercury 200hp I need to do this aswell since my seals are leaking. What all do I need to do job??
@byronargueta3331Ай бұрын
@@matt98eclipse I need to do the same work , my seals are leaking as well, same exact motor. Do you have any tips? Did you get the job done? Can I rebuilt the Cylinder without having to looses or remove the motor bracket or steering?
@mikesanders9023 жыл бұрын
Dic
@mikesanders9023 жыл бұрын
Waist of TIME!,,'!,,,,,
@jamesmichon14254 жыл бұрын
Dude, its a 30 min job to replace and about 2 hours if you rebuild. Sell the boat and get a skateboard.
@THEcombatXD2 жыл бұрын
Sell your self instead .
@treyjohnson6852 Жыл бұрын
Why even comment? What a ruthless worthless person you are. Like ole boy said go sell yourself
@johngrady35324 жыл бұрын
The Cylinder is ez pz to get out the unit u need to take the motor brackets off be careful!
@byronargueta3331Ай бұрын
Is it possible to rebuilt Cylinder in place if I'm able to successfully remove trilobe pin?
@henryfahnestock27834 жыл бұрын
dude, there is a small pin you back out with a hammer and chisel
@davidjessee77014 жыл бұрын
Ah ah ah ah and ah ah ah ah and ah but ah ah and ah
@mikedescoteaux8395 жыл бұрын
Go to Home Depot 10 bucks get a hardened steel slender long punch drive that top pin out . Upwards and rebuild the cylinder in place as you said at the end.
@kencrockett30635 жыл бұрын
First of all the easiest way would have been to remove the starboard transom bracket. I know that sounds like a lot of work but better than screwing everything else up. Really not the best engineering in the world, but this is how you earn your nuts as a marine mechanic.
@briancarlin18175 жыл бұрын
What a total waste of time! You never did get it out
@fogduker31315 жыл бұрын
Easy job just changed mine half hour job piece of cake
@byronargueta3331Ай бұрын
I need to do the same work , my seals are leaking as well, same exact motor. Do you have any tips? Did you get the job done? Can I rebuilt the Cylinder without having to looses or remove the motor bracket or steering?
@billdeere74206 жыл бұрын
I tapped mine out...the pin up top centre ram.. "PUNCH"... longe slender sucker... then remove the larger pin up top centre...GOOD LUCK
@jrmarine20776 жыл бұрын
He wasn't high thats how you do it . Thats a 30 min job max
@thegloriousriderfl30596 жыл бұрын
TopTime Fishing How do you get the whole unit out
@terrysilliman58156 жыл бұрын
TopTime Fishing You put a jack stand under the foot and ratchet strap it , then take the side bracket off then if the top pin don't come out you drill it out and buy a new one . It's actually a fairly simple job once yo get the engine supported safely.