How are you connect 2 different iPhone with obs camera app? I can only make one iPhone show at a time
@hackbatch27 күн бұрын
You need to add a new source for each iPhone in OBS.
@armandoperez344727 күн бұрын
@@hackbatch what the heck?!!! I have had and used the obs camera app for years and didn’t know I can connect multiple iPhones to it. I try it a few hours ago and it didn’t work. But I just try it again and it work. I had to connect and reconnect one of the phone so they can be recognize. Thank you!! This have save me a lot of headaches
@hackbatch27 күн бұрын
Glad you got it working!
@Createstuff131328 күн бұрын
Wow!
@BeatsbyLonza29 күн бұрын
Thank you.
@3dmaker186Ай бұрын
I am trying to do this on the Neptune 4, using cura. The problem I keep having is just as the pen is about to hit the paper and begin plotting I am getting a klipper message saying - PLEASE RUN ‘SDCARD_RESET_FILE OR ‘FIRMWARE_RESTART’ TO RESUME.!! Extrude below minimum temp It seems the printer will not allow me to run Gcode with the extruder temp set to 0. Can anyone Help
@hackbatchАй бұрын
I have no experience with Klipper firmware but it sounds like the firmware has a setting that doesn’t allow for 0 temperature. I would try disabling the hot end in Cura in your machine settings. I am not sure if that will do it, but it might help. Otherwise, I think this might be a firmware level restriction with Klipper.
@3dmaker186Ай бұрын
Thanks for getting back to me, where would I find the option to disable the hot end? I can’t seem to locate this.
@hackbatchАй бұрын
@@3dmaker186 It seems I am misremembering a setting in Cura that does not exist sorry. It looks like you can disable the heated bed but not the nozzle. Not sure what the solution is here besides a change at the firmware level. or possibly manually replacing lines of the GCODE file to not move the extruder motor. The method shown works with Marlin and that's the only firmware I've tested it with.
@charlie1872Ай бұрын
Hi, Very interesting. I have a model railway youtube channel and publish through Streamyard. I try to use multiple webcams/iphones but have run into problems with the cameras dropping off. My setup is through my Macbookpro. I wire the webcams in through a card/usb hub and the iPhone(s) I invite via Streamyard. Any ideas would be appreciated. Thanks
@hackbatchАй бұрын
Hi I have never used streamyard so I can’t say much on that. The setup I use here uses a few different apps with OBS. They are all linked in a blog post in the description of you are looking for alternatives to try. There’s an app called Detail that I have seen for Mac and IPhones that’s lets you do multicam over USB as well. Might be worth a look
@charlie1872Ай бұрын
Thanks for responding, I appreciate that 👍
@TheHazarrrdАй бұрын
Great Explanation. I wonder if this would work with some 4k Webcams like a Logitech Streamcam as well? This would make producing multicam so much cheaper..
@hackbatchАй бұрын
I’m sure this will work with any type of USB video source including webcams! I just had the extra phones laying around so I tried that instead. Thanks for watching and your feedback.
@Boss0LeenyАй бұрын
Is this possible with STREAMYARD ❓❓❓
@hackbatchАй бұрын
I don’t know I’ve never used Streamyard, sorry
@mokenOSАй бұрын
Uh...Latency?
@hackbatchАй бұрын
I didn’t test anything for latency because I didn’t really experience anything noticeable. But perhaps I don’t understand your question. I was recording and not streaming so any inconsistency can be removed in editing.
@mokenOSАй бұрын
@@hackbatchThanks for the response! Using a canon 700D as webcam produces noticable latancy for me. Maybe its different with newer cameras and USB-C? I do know about the Latency compensation thing in OBS but i want to simplyfy the process and Having multiple cameras with different latencys recording into one single video file seems like a pain to synchronize. Wanted a way around that but i guess thats just how it is when using USB. But i realize now what im actually looking for is a no latency multicam STREAMING setup. Even though i might just be recording. Something like the "Elgato Cam Link Pro" is what I need....i think....
@hackbatchАй бұрын
@mokenOS Sometimes things are easier to implement in hardware but that usually means more expensive. Also note that I only have the iPhone and smartphone cameras connected over usb straight out of the device. My camera at the time as a canon m200 and I was using a cheap hdmi capture card to turn it into a usb video source but I was not using that camera as a usb webcam with any canon software. That might help to try a cheap capture card first and check the latency. I know that the USB webcam softwares can sometimes introduce latency and lowered resolution.
@nowyatalking2 ай бұрын
Back again how do you split the video sources evenly on the screen thanks in advance
@nowyatalking2 ай бұрын
Also how do you record in 4k
@nowyatalking2 ай бұрын
Also how do you record in 4k
@hackbatchАй бұрын
You can make a scene that has 4 different sources in it and resize the sources and position them in the scene window in OBS. To record 4 streams in 4K you would need to have an 8K scene or at least computer hardware capable of processing 8K video.
@nowyatalkingАй бұрын
Thanks again for the info you've been a great help Ive been trying to built a low budget multi cam setup for the last month this is they way I'm going 💪🏾
@hackbatchАй бұрын
@nowyatalking Glad I could help! Good luck
@Rigo6872 ай бұрын
KZbin keep pushing bs videos from think media where they show you bs junk products and teach nothing. And if they find this video automatically they copy and paste a bs version.
@beyounow72042 ай бұрын
Perfect! Straight to the point. You saved me so much time in explaining what I needed to get going. THANK YOU!!!😃
@useruser-oc8xn2 ай бұрын
Nice! Thanks for the info.
@Pitech20002 ай бұрын
kzbin.infoVmBM_z_rc_s?si=ZOWgTXTpHZoVH-au
@Boss0Leeny2 ай бұрын
Will this work for Live Streaming in real time ??
@hackbatch2 ай бұрын
In order to record the multicam scene and live stream at the same time you would need to use the Source Record plugin which is a 3rd party plugin similar to the other software shown. If you don’t need to record and only want to livestream you can just use OBS like normal.
@TheMilford2 ай бұрын
does it need to stay as the quadrant or can the footage be edited later into a single frame with edits? excuse the noob question.
@hackbatch2 ай бұрын
The footage can be cropped and edited in a video editor later on. So you can record as quadrants in one file and edit it later on separately from this process.
@purpkisses75993 ай бұрын
Thank you thank you thank you. Could you possibly do a 1 on 1 to help someone? Or do you have a detailed video on the apps and plug ins?
@hackbatch2 ай бұрын
In the description there’s a link to the blog post with instructions and the plugins you might find helpful!
@user-xd9xs5wu7l3 ай бұрын
what if i want to record each camera in 4k resulotion?
@hackbatch3 ай бұрын
That might be difficult depending on your computer’s performance. I don’t think you can record in 4K for each camera simultaneously using this method very easily.
@WTSPod3 ай бұрын
was curious how you didn't overload your usb hub with multiple cameras?
@hackbatch3 ай бұрын
No clue, I had it plugged into a usb c port on my MacBook. I always wondered what the limits were.
@NiMareQ3 ай бұрын
When I first installed the Z offset extension, it did work for me, but throughout experimenting, maybe also after I installed few more extensions, I could not get the desired effect whatsoever. It was frustrating. Though, I managed to work around it by initiating the print and hitting PAUSE immediately on the printer (after it did the initial moves, but before the print). Then I manually adjusted the z-offset on the printer under tuning and resumed the print. But before that, it broke the tip of my pen... What a frikkin force.
@NiMareQ3 ай бұрын
Will this work with Creality Slicer too? /edit it does
@skrie3 ай бұрын
Will the printer not try to extrude the filament anyways?
@hackbatch3 ай бұрын
The nozzle is not heated. I suppose it might be trying to move the filament but if that is an issue you can unload the filament before plotting.
@kibsonator153 ай бұрын
guy. I did everything as you showed, but my cura won’t slice the drawing.
@hackbatch3 ай бұрын
Check that you have at least 2 layers in your STL before you slice it. I had some trouble when the file was too thin.
@FortheLoveofIt-podcast3 ай бұрын
This is amazing. Thanks for the help!
@nowyatalking3 ай бұрын
Great video very helpful 💪🏾 question how do you get different video files if everything is recorded together? Or do you record all 4 on one screen than crop each into 1 shot in editing
@hackbatch3 ай бұрын
In this example I am recording them into one clip and then cropping in editing. I have tried other methods such as using the Source Record plugin for OBS but have not gotten it working reliably.
@nowyatalking3 ай бұрын
@@hackbatch thanks your the man I'm trying this out asap I currently use the advanced switch while recording it works great but sometimes while editing it gets a little to chopped this method give me more control of the editing 💪🏾
@ejaybeatz36094 ай бұрын
how do you edit all video clips or are they just combined all in one?
@hackbatch4 ай бұрын
You can record a single 4K clip with all four 1080p sources within it and then crop multiple copies in the timeline of your edit allowing you to switch between which view is showing in your editing software.
@TSquadRVing4 ай бұрын
Thank you so much for this video. Helped us out!
@mavisbroadcast4 ай бұрын
Hi team @Hackbatch - this is great, thank you for sharing. We would love to put Mavis on your radar, too. This is a cloud-based solution that enables multi-camera productions. Would you be interested in a free trial? Look forward to hearing from you. Cheers, the Mavis team.
@hackbatch4 ай бұрын
Hello, for business inquiries you can visit my website which is linked in the about section of my channel. Thanks for your interest in my work!
@Random_stuff9604 ай бұрын
I’m going to use this to try and make a homework machine with chatGPT, any tips?
@wesleyhale44724 ай бұрын
Change the last like of your G code to hop up more than 0.2mm after it finishes before wiping to the side so you won't get that weird line at the end
@hackbatch4 ай бұрын
I have since made that change because that bothered me the first time around! Thanks for the suggestion
@johmu54664 ай бұрын
Great job on all ! The video editing is outstanding*...!! (*concise & very entertaining storytelling; great action cuts too..!)
@hackbatch4 ай бұрын
Thanks!
@happybaak5 ай бұрын
WOOOW! This is what i am looking for a looooooong time! This is very very helpful for me! Thank you for this very important information.
@hackbatch5 ай бұрын
I’m happy that it was helpful!
@falonvela91975 ай бұрын
This is amazing!!! Thank you so much!
@hackbatch5 ай бұрын
Thanks! Glad it was helpful
@safetyhomeloans9505 ай бұрын
loved your music selection, I found the artist...I just wanted to ask what the name of the song was. thank you
@hackbatch5 ай бұрын
Thanks! I make most of the music on this channel in GarageBand if they aren’t made and credited to someone else. I cannot actually find the name or the file of the song on my computer.
@centpushups5 ай бұрын
Get a drill tap threader for those holes. Never needed a nut ever again. One of the most revolutionary thing I did for my prototypes.
@hackbatch5 ай бұрын
I mostly use heat set threaded inserts for my prototype parts nowadays. Thanks for the tip!
@hermanherman19825 ай бұрын
Thank u for that. May i ask something? Lets say i have cameras…. LG Brio stream connected straight to a PC recording a scen from 2 angles and normal camera with LCD screen in my hands. No capture cards what so ever. Will this work? After copying material from camera in my hands, to my pc i would like to make movie using bits from all 3 cameras going back and fourth between files (cutting them in to smaller files and using them here and there) sorry fot „buttery butter” type of comment, im new to this. I used to stream live, never made movie. What to use to edit and render please?
@hackbatch5 ай бұрын
You can use a video editing software like Davinci Resolve which is a free download to drag your clips into a timeline and crop them to be the right size and switch between them in sequence.
@OnlyCocoMousse26 ай бұрын
Can Obs Record 4 separate camera inputs as separate file?
@hackbatch6 ай бұрын
You can do that in OBS with the 3rd party Source Record plugin. I have never gotten it to work very reliably however.
@gearscodeandfire6 ай бұрын
Awesome documentation
@gearscodeandfire6 ай бұрын
Great video, looking forward to more!
@gearscodeandfire6 ай бұрын
Yep- i’m loving how you document your process- I am really looking forward to your channel blowing up because I think it’s pretty awesome
@hackbatch6 ай бұрын
Working on making better and better things in the future. I hope it works out too, thank you.
@gearscodeandfire6 ай бұрын
Dude this is exactly what I needed- I have been using WLED for three or four years now, but I never realized it had a pretty accessible python interface. Great vid
@hackbatch6 ай бұрын
Thanks! I plan on messing around more with the real-time interface with python for some more experiments too. Good luck!
@gearscodeandfire6 ай бұрын
commenting for the algorithm while continuing to binge on your stuff, well done 🤘
@gearscodeandfire6 ай бұрын
This is an awesome and clever implementation AND it introduced me to your channel, which i am currently binging 🤘
@hackbatch6 ай бұрын
Thanks so much, I’m glad you are enjoying it!
@brokerhc6 ай бұрын
Does the OBS software come for Windows PCs? Great video, very informative.
@hackbatch6 ай бұрын
Yes I use it on Windows now as well!
@valerieconsalvo88246 ай бұрын
Wow this is amazkng Derrick congratulations
@hackbatch6 ай бұрын
Thanks so much!
@esemulka6 ай бұрын
I am trying to resize my 2 multi camera video with a small PIP in right bottom corner. I have the capture of the 2 camera video but how do I resize or edit the video to place one of the videos in the right bottom corner of the multi video recirding?
@esemulka6 ай бұрын
Also I am using me cell phone to record the above 2 camera video to edit.
@hackbatch6 ай бұрын
You have to use two copies of the video clip in your editing software and crop it to the right size and place it where you want. Using a 4k file to record will get you four 1080p videos when cropped to the right resolution.
@muellerhans6 ай бұрын
The project page doesn't seem to exist anymore?
@hackbatch6 ай бұрын
Sorry about that, I just updated the link in the description. It should work now!
@plinden6 ай бұрын
wow! this saves us 1K compared to logitech 3 cam box