In short - this is some absolutely horrible engineering by the designers….fk Chrysler
@ChuckAustinWNY3 ай бұрын
Awesome video. I hope that you make more videos.
@mm-20187 ай бұрын
Chrysler three hundreds are notorious for i They should actually recall the shit
@michaeljennings80827 ай бұрын
Nice job. I’m glad you did the video. Are all of the blend doors the same? Or are they different shapes? Have you done rear shocks?
@Procharged7 ай бұрын
All the blend doors are the same. Yes I've done rear shocks, they're pretty easy. Just unbolt the lower control arm at the knuckle and it gives the shock enough room to come out if you compress the shock.
@twotoneprixflako956 Жыл бұрын
one question on my 300 2014 my driver blows cold but not my passenger side? what it could it be
@utubbabe1234 Жыл бұрын
had the one done on thee other side , center and was charged 700.00 for the job ..what a load of crap...when you figure our how too doe thee drivers door actuator ..I hope you post it because that one his starting to act up too......oh ...and that you😆..I'm a girl💕
@pelvicthrust119 Жыл бұрын
The white piece with the green plugs just slides up and the whole thing comes up do not unplug each little green plug😅
@marlenbarajas1352 Жыл бұрын
How do u know which out of the 3 is bad
@marksmithjr00 Жыл бұрын
So mine is clicking and with the air conditioner on the driver side is hot in the passenger side is cool? So which one do I replace the bottom?
@BrianJimenez-ft2tv Жыл бұрын
Are all blend door actuator the same
@lindseygarcia3675 Жыл бұрын
This is like the best video ever!! Thank-you for making this much appreciated! 😊 👍🏻👌🏻
@mattyice2216 Жыл бұрын
to remove the upper air door actuator; remove the guage cluster, there are videos available on how, easy.. have a friend with small hands help
@MusicalMartian2 жыл бұрын
Ticking, train horns. OMG lol but hey great video for reference.
@brucemeyer63452 жыл бұрын
Any chance there's a video on how to change the top one?
@jackwadeiv9562 жыл бұрын
The hard lines you are referring to under there on the drivers side are coolant lines for the heater core. My car is clicking and I have identified the top actuator as the culprit. Can anyone tell me the process for dropping the steering column down? I have a 2011 Chrysler 300 C with the electronic tilt and telescopic steering module. I think if I do that changing that one will be easier.
@brucemeyer63452 жыл бұрын
@Alex Hinsey I need some help if you can. The instructions were great and it helped me change out the actuator. But I discovered the clicking sound is not the actuator but the part the actuator connects to. Whilst in the process of changing it out, after I took the old actuator out and before I put the new one the piece the actuator connects to started clicking! I am assuming I need to change that part out but I have no idea what it is called or how to find out what it is called. I have done searches for a dash diagram and even just the AC/heat system on my 2012 Chrysler 300 but I have found nothing to help me identify the part I need to replace.
@tomcraftdonkey228511 ай бұрын
Did you ever find the part number?
@chrisarmstrong37272 жыл бұрын
Thank you a ton dude 🙏🏼
@eddielasola8882 жыл бұрын
Didi you figure out how to replace the second blend door actuator? Any vids? Thx!
@ChuckAustinWNY3 ай бұрын
I was just looking and this is the only video EVER, too bad this guy is good at making a video.
@egm135able2 жыл бұрын
What type of screwdriver it's used??
@nickj61863 жыл бұрын
just did the back one, took about 3 hours without removing the dash, thank you for the video on how to get to it!
@johnyondabeat17502 жыл бұрын
Helllllpppp
@el7mane43 жыл бұрын
Bro you never did a vid on the top one😭😭
@Procharged3 жыл бұрын
No, I planned on it but had a bad bike wreck so I cluldnt. Had to have the dealership do it. He did the same thing but pulled the steering column and got right to it.
@catherineharris273 жыл бұрын
Nice video...Step by step! Thanks bunches! I need mine done as well. My whole dash lights are flashing as well n now its clicking so bad. Its driving me insane! Thank you so much for this video. Now I can get the parts n tools to get mine replaced.
@NODARKNESSNOLIGHT3 жыл бұрын
3012 wow that’s really new😂
@Crysalis020103 жыл бұрын
Thank you bro. Add "Dodge Charger" to your description as they are the same! :)
@xl68973 жыл бұрын
Was that the mode door actuator?
@tellyarmstrong6333 жыл бұрын
No one is showing me how to get the upper one.
@BlackGoat323 жыл бұрын
Does this work for older versions?
@antoniojimerson20953 жыл бұрын
These instructions were really great. Suggest anyone trying this to take the steering column down. It makes it so much easier. Thank you kind Sir. 🍺
@RamonHernandez-ux4uz3 жыл бұрын
Thank you very much young man S.A. Tx
@franklinquiroz28983 жыл бұрын
Great video! I used the same steps to replace the top driver side actuator on my 2012 Chrysler 300. YOU DO NOT NEED TO TAKE THE DASHBOARD OFF. It’s a crazy hassle to remove the top one yourself but it’s possible.
@ricardov12853 жыл бұрын
You know where i can find a tutorial for the top drive side?
@johnyondabeat17502 жыл бұрын
Helppppp
@LingoENT Жыл бұрын
I think he sleep 🤣
@MrBigrigs243 жыл бұрын
2013 Chrysler 300S same problem somewhat heat only comes thru defrost when I cycle to feet it only continues to blow thru defrost which actuator should I change
@nickj61863 жыл бұрын
the one shown if its drivers side
@brucemeyer63453 жыл бұрын
I took a picture of the other screw. In this picture there are two identical screws right next to each other. Only the top one is for the actuator. linksharing.samsungcloud.com/yZRxbg2unOKr
@brucemeyer63453 жыл бұрын
Thanks! I have replaced the one blender door actuator on the passenger side multiple times. I just started getting the clicking sound on the driver side and wanted to see how to replace the actuator. I contacted chrysler service to see if it was the same actuator and they said it is, The thing is you say there is two but the service people say there is only one on each side.... If there is a top one I just hope that isn't the one that is bad.
@concentratecorner17443 жыл бұрын
theres two on dual climate cars i know for sure. One controls temp other controls modes like changing to defrost and where the air blows from the various vents.
@David-zj3bp Жыл бұрын
@brucemeyer6345 I just got a 2013 Chrysler 300 and it makes the tapping noise under the dash on the passenger side. It does does the noise after I turn the engine off and sometimes while I'm driving. Also the air recirculating button flashes a couple of times when I press it. And then the button light turns off. I read that's the humidity sensor behind the rearview mirror. Any tips/advice would be greatly appreciated. Thank you.
@pantae29464 жыл бұрын
Thanks bruh, but are both actuators the same part?
@Captain_Dark4 жыл бұрын
If anyone is wondering the top one is temperature control and the bottom one is for vent control.
@reggielamay38704 жыл бұрын
Temperature control is the one under the push start button? My 300 blows hot before it blows cold ? Thanx.
@Captain_Dark4 жыл бұрын
@@reggielamay3870 No it's above it. The one below it is for the vent controls. Be mindful that under normal conditions it will be hot before it cools down. Shouldn't be more than a few seconds before it cools down though. If yours isn't cooling down or it's stuck then change the top one. Drop the steering column to access the top one makes it way easier.
@reggielamay38704 жыл бұрын
I replaced the one thats super hard to get to “ very tight spot” but now my ac blow hot for about 2 mins then its starts to blow cold. Do i have to recalibrate? Or just replace the other one? Thank you for your replies
@Captain_Dark4 жыл бұрын
@@reggielamay3870 Is that the one near the push start button? No you don't have to recalibrate it mine just worked right after installing it.
@reggielamay38704 жыл бұрын
I replaced the one further down by the gas pedal. It was making a clicking sound. Ive replace it twice already. But now its hot when i start the car then eventually starts to blow cold
@kimberlyhill91904 жыл бұрын
I am having a problem with my ac blowing through the dash vent versus the front vent when I have it set to blow from the front vents. I am sure it is an actuator problem but not sure which actuator it is on a 2015 Chrysler 300. I had the problem with ticking sound about two months ago and had that actuator replaced. Do you have any videos that show this issue or can you tell me the name of the actuator to be replaced?
@rigovertovaldezjr81552 жыл бұрын
So am i let me know if u found the solution
@David-zj3bp Жыл бұрын
@kimberlyhill9190 out of curiosity around how much did it cost to get the actuator replaced? My 2013 is making the tapping sound on the passenger side. Thankfully it's not all the time
@louregal994 жыл бұрын
Maan this is a GEM! Good loox bro!!!
@im2technical1634 жыл бұрын
Do you have a video for passenger side
@angelarogers80514 жыл бұрын
I think you should have shown what it takes to replace it! Not how to take the car apart
@Procharged4 жыл бұрын
You have to take the car apart to replace it genuis. All I left out was removal of 2 screws and it will fall out. If thats too hard for you to figure out you need to take it to a professional.
@thebellfamily61594 жыл бұрын
What size tool did use to get the screw out ?
@devinh2432 жыл бұрын
7mm
@TrayJayRecords4 жыл бұрын
Hey man thanks for this tutorial.. I just copped a 2011 and its doing this just less severe.. I wish I had tried to change the air flow before buying so I would have known going in.. did I mess up buying a 300? Kind of scared if this is just a taste of what’s to come
@Procharged4 жыл бұрын
No way. 300s are awesome. They wear out the suspension faster than most cars and these actuators like to fail pretty often but thats about it. I'm a parts manager at a Chrysler dealer and the 300 is the car we see come in the least by far.
@louregal994 жыл бұрын
I gotta 2010 last year, and it's been mega low maintenance. They're great cars bro
@TrayJayRecords4 жыл бұрын
Lou Regal yeah bro i’m loving mine already decided that it can throw me problems it’s worth fixing and having the only badass American sedan on the road
@Mudoh4153 жыл бұрын
They don’t do that great as the years add on. I’ve had mine about 8 years and I had to add a maintenance section to my monthly budget.
@David-zj3bp Жыл бұрын
@@Mudoh415I just got a 2013 300 with 139K miles. The only problem I'm having so far is the tapping noise under the dash on the passenger side. I think it depends how the previous owners drove it and maintained it. As you know some people abuse their cars and don't keep up with maintenance. I also need to replace the humidity sensor that's behind the rearview mirror. It doesn't let the air recirculation stay on (button light flashes twice and the light turns off).
@johnchaney63964 жыл бұрын
Do you have a video for 2006 Chrysler 300 driver side blend door actuator?
@ckaisermomx34 жыл бұрын
I had mine changed at the dealer and now there is a green "hose" sticking out in my driver door jam that is rubbing my door...any idea what that could be?
@Procharged4 жыл бұрын
No I don't. Thats odd. It may just be a part of the door seal but you should take it back to them just to make sure they got it all back together correctly.
@emanuellaysr93474 жыл бұрын
How will I know witch aculator need to be changed
@so_mississippib20134 жыл бұрын
Minds doing the same thing so when does that have anything to do with my circulation button not staying on
@so_mississippib20134 жыл бұрын
@@Procharged I figured out what it was it's my humidity sensor above my review mirror I have a Chrysler 300
@renearambul69554 жыл бұрын
@@so_mississippib2013 how did u gey it to work? I ordered the sensor brand new and installed it and my circulation button still won't work.
@so_mississippib20134 жыл бұрын
@@renearambul6955 I haven't or6it yet and sense u said that I might have to take mine to the shop and get it fixed we might have the same problem so mo need of me ordering new one if u get yours to work let me know how u did it
@renearambul69554 жыл бұрын
@@so_mississippib2013 hey so my bad i guess at the time i installed it yesterday there was humidity in the car or something and it didn't work... but i woke up this morning and it was working perfectly the circulation button stays on now i get colder air and no smells from outside.... i recommend you order it.... i got mine from ebay for 50 buck totally worth it.
@juanbautista4234 жыл бұрын
Gracias brother arreglado
@jasonmcintosh95334 жыл бұрын
I changed the top in 30 minutes? Not sure if the 2014 is different? Either way, great video.
@stefansensenbrenner59224 жыл бұрын
Did you change the exact same blend door that he is talking about on this video?
@stefansensenbrenner59224 жыл бұрын
I have 2009 and looks very similar looks hard to get to for sure in my car
@steveod31984 жыл бұрын
The top is ridiculous to get too unless maybe you take part of the steering wheel off?
@pantae29463 жыл бұрын
Jason how did you change the top? Did you have to remove the whole dash ?
@JoeSmokinAllDay5 жыл бұрын
You dont need to unplug the airbag plugs or rempve the hood latch, just tuck the panel up in the door jamb. So those wonderkng, its a T15 bit for the gold screws
@nickj61863 жыл бұрын
its a 20
@tonyjaquez35958 ай бұрын
I watched this 2 times thinking I may have missed the T size....thanks for this!
@robertboatright64525 жыл бұрын
Have you done the video for the upper one yet on the drivers side?
@Procharged5 жыл бұрын
I have not, I know how to change it but I wrecked my motorcycle and have been in a wheelchair since, as soon as I can get around easier i plan to make a video on it but its going to be a good 8 months or more.
@robertboatright64525 жыл бұрын
@@Procharged oh no! I'm so sorry to hear that!! I hope you have a speedy recovery friend. God bless. Ps. Can you tell me if removing the dash is necessary?
@robertboatright64525 жыл бұрын
Nevermind I just read another response you gave about removing the steering column.. I think I got it