2 жыл бұрын
3 жыл бұрын
4 жыл бұрын
Пікірлер
@HoraceKLai 5 ай бұрын
Cant get the clips off after removing the screw. Any videos on that?
@niclasbenett6779 6 ай бұрын
Thank you so much! Was set within like 15 minutes, seven of which I was watching the video. You don’t have to twist or tilt the clips. They have to be bend fully upwards to insert, there are scores on the angles which need to fit. With forceps I then put the band on. Great help, thank you!
@ragmennemgar7879 10 ай бұрын
Ja kupiłem poleasing i właśnie już mial 1 czy 2 wciśnięte w głąb i prawie żaden nie wypycha się w stronę kubka. Nie wiem czy to naprawiać skoro nie używam żadnych kubków 😂
@george_meta Жыл бұрын
Can you buy these clips individually? I am looking to perform the same thing in my Passat.
@aleksanderspyra5722 Жыл бұрын
Haven't really checked, but I doubt it. Probably a heavily used central console trim is the closest option. Did you lose yours? They are probably still there, wedged somewhere :)
@westkot8459 Жыл бұрын
This video is so helpful thank you for making it🙏🏼 Yesterday I pushed one of these clips in on my new car. I got worried that I have to replace the whole thing but then I found this🙏🏼 I have to get to fix the rear right side clip. And this video is so helpful for me. Thank you so much for making this☺️
@aleksanderspyra5722 Жыл бұрын
Thank you! I was really frustrated because of the lack of information about this particular repair, and decided to spend some of my time on the video so that others will spend less. Comments like this one make it worth it!
@adamku808 Жыл бұрын
God bless this man
@bennguyen1313 Жыл бұрын
Do you know if the same AT-Atmel-ICE debugger adapter can also work on *ANY* chip that supports JTAG,SWD/SWO? For example, can Eclipse+OpenOCD see the AT-Atmel-ICE and debug a SmartFusion2's Cortex-M3? Or do trace-streaming via SWV/SWO?
@RGB_Reglin 2 жыл бұрын
Świetny filmik.
@konstantindolgan1805 2 жыл бұрын
Aleksander, I'm trying to program a custom PCB with an Atmel ATSAM3X8E AU MCU via ATMEL ICE programmer. The board doesn't initialize in Windows and a COM port doesn't get opened by Windows when a USB cable is plugged into the PCB. I was able to upload the code (simple blink test) via Microchip Studio, but it seems like the program wasn't running on the MCU after uploading. It appears like the MCU bug you mentioned in the beginning of the video. Is it possible for you to provide a simple step-by-step instruction on how to fix the issue in my case? I would be glad to connect on Telegram or Skype to go over the issue with you. Also, I don't mind paying for you help. Please let me know.
@aleksanderspyra5722 2 жыл бұрын
Hi Konstantin, In Microchip Studio, there should be a way to check and set the GPNVM bits that are responsible for executing from flash when programmed. I'll try to find it and will get back to you.
@Octocat 2 жыл бұрын
I've seen this in action and I'm very excited to make my own! Thank you!
@tusharbadyal6549 3 жыл бұрын
Could you please help with SWD pinout mapping of STLink with Due.
@aleksanderspyra5722 3 жыл бұрын
The DUE SWD pins are marked DEBUG - you can see me connecting to them in the video. They are, numbered from the USB socket side: reset, swdio, swclk, ground. DUE reset - STLINK RST (pin 1) DUE swdio - STLINK SWDIO (pin 2) DUE swclk - STLINK SWCLK (pin 6) DUE ground - STLINK GND (pin 3/4)
@dnighthawk204241 3 жыл бұрын
Great design! I was searching for some kind of open cylinder option for the hurricane, and it took me ages to find this. I think it's criminally underrated.
@larce4158 3 жыл бұрын
You may have just convinced me to buy one of these for secondary rounds, great design!!
@mangofactory.mp4 3 жыл бұрын
Just came across this from This Week in Nerf and now I know what I want for Christmas
@FoamBlast 3 жыл бұрын
These are simply ingenious.
@Steampuke 3 жыл бұрын
Wow, thanks youtube for recommending this sweet vid