Good tip from me is to make sure the RX is taped down well so it doesn’t move around or you will crash ! So no Velcro guys !!! I learned that the hard way! Speed running at 117 mph and a bump in the road dislodged the RX from the Velcro and the car turned into the hedge !

I started to do this after getting impatient with using my heat gun, but started to worry that would make it harder to put back on. Thanks for clearing that doubt!

I watched many videos on KZbin and looks to me that you know most about this transmitter and receiver so I have a question. How do I set up my Kraton 8s so I have to hold the silver button to go in reverse and disable it from its current normal mode.. thanks so much and great videos.

Thanks for the video. It’s close to what I want to do. But I don’t plan on running a body. I was going to build my own chassis and the front end would be wider. I’ve spent countless hours researching and not sure what direction to go yet with a front differential. Whats the overall gear ratio with those TRX-4 portals, I actually have GPM. They look almost the same. I ordered some dogbone shafts and tried to fit them today but they won’t work. The pins are too wide for the upper inner portal stub. Do you have a part number on those axle shafts and the diff? Thanks for any help. I have a massive folder with so much information in it. 30% now is probably worthless because I’m learning as I go. I have this stuff in the real world. It’s very very expensive. But in the RC world it’s like starting all over again.

I want to hear more about this portal ifs build. I already have parts.

Great video 🫡🫡

Absolutely rad. Some HEAVY heavy fluid in the center and rear diff is the best thing you can do for these things, makes them much more capable on the technical sections

I didn't realize you were local to me. My Hammer Rey shows up this week, I will have to go check this course out!

Great review! Have you tried the Flysky GT5? their AVC works quite well and you can adjust the throttle control and steering control levels independantly.

It's way easier to cut the rear portion off and then make the cut behind the fenders because you can hold on to the bed the whole time

Hello Phil as You are probably aware that HH has these on sale and as an RCing Hobbiest with the Addiction I've acquired both Red and Green one's and researching led me to your channel and have subbed...will be watching more of your videos... Thanks for Sharing the information on the Hammer Rey ✌🤠👍 HFLPRCing =Having Fun Laughing Playing and RCing 👍😎👍 AOAH =Association of Addicted Hobbiest 🙏 SSPH =Stay Safe and Play Healthy My Friend and Have a Great Week 🌟 Blessings from The Great Smoky Mountains Tennessee

I put at least 40 packs through it, zero issues. drive it normal, not like kevin talbot. this winter going to upgrade steering system and address some handling issues. it has been become my favorite RC

Same problem im having nice video bro. Just subbed to your channel.

Did you put on 3s 5000mah ? You don’t have any themperature trouble with it ?

Ordered same shocks and springs you mentioned and flex is night and day! Thanks for putting this out.

nice video. I'm new to your channel. which camera do you use for your video's I'm looking to purchase a Go-pro

That was way better than the instructions from radio link lol

What do I do if I am already using all of my channels on my receiver? I am using channel 3 for LED lights. How do I adjust the sensitivity of the Gyro without affecting the lights?

The gears cog out like that and make that grindin noise in the diffs because the stock spectrum setup ESC & motor is sensor less combo. If you throw upgraded censored rock racer set up in there it’ll make a completely different rig. It’ll crawl way smoother with no gear cogs ✌️

Great help!

I had one of these and got rid of it after not too long. I dislike having to remove several screws to remove the body. Also, getting to the center differential is a nightmare. I prefer the TEN platform.

Appreciate all the info!

*Uffffff Caótico Color brother 💯*

are the trailing arms from element?

Rood Bridge Park?

Looks so good!! 👍

I love your passion for this vehicle. Great review bud

Using it exactly for what it was made for. Great video 👍

I think I can maybe do this if I had a track and was good with drifting

Nice job on the truck bed it looks good

Nice. I have the Element RC IFS kit installed on my SCX10 II.

What a cool place to run an rc. Nice!

Your driving skills are so good 👍🏼👍🏼👍🏼 Best driver

This is a very nice video. 👍🏼👍🏼👍🏼

@3:55 so what problems did changing the 3rd member fixed ? I don't think you ever got back to that in the video. I am asking because I got this and it's my 1st RC car so I am trying to learn as much as I can about it.

That was an awesome event!

Nice job on that looks 👍

Hey Phil, nice review. Please help. whats parts did you say will fit this? parts from the Baja Rey or the Rock Rey? thank you

Fun fact : everybody likes to read funfact

Somebody send it to Elon Musk

Here I am before it's famous

Who else is here before it hits 1 Million views

Noice🗿

damn it looks cool

That thing is way more stable than I thought it would be

here before its famous

Сподіваюсь уламки не потрапили на житло?

Nice

good video fam🤓

Good video man, I really like that paint nice job