Baseman

Пікірлер

@williamwatkins821 Ай бұрын

Baseman! i'm working on my cb400f and i can't get it to run really nice like yours. it seems to either lug at low throttle or lug at high throttle, no in between. how did you get yours purring like that? standard jets, 2 turns out on the mixture screws?

@sebs27 Ай бұрын

Best would be go through everything very carefully, check the rubber inlet manifolds for cracks, then clean the carbs very well, the jets may be clean but sometimes the fuel passages may be blocked 1 1/2 to 2 turns should be correct check float levels to, to much/little fuel in the bowls can cause a lot of smooth running issues

@foxtrotwhiskey874 Ай бұрын

Hi, my father had this identical 110cc Benly, same decal on tool box and tank art work. its more likely a 71/72 model year.

@simonbelanger3257 2 ай бұрын

Tout ce travail pour rien.... Cest bien la 1ere fois que he vois ajuster le ralenti moteur et surtout le vacuum des carburateur SANS ECHAPPEMENT🤦. Tout sera a reprendre rendu sur la moto🤷

@sebs27 Ай бұрын

of cause once its in the bike I will need to re check settings, but its always easier doing all the first checks outside, the carbs are not easy to remove once in the bike

@ummr89 2 ай бұрын

Looking forward to an update.

@sebs27 2 ай бұрын

Hi, there will be a update, I just haven't had the time to continue much currently.

@JasonOxenbury 2 ай бұрын

Beautiful kickstart action . Your legg must ache . But sounds gorgeous when started . . Nice bikec😊

@sebs27 2 ай бұрын

Thanks. These bike thumpers can be quite a handful to start

@JasonOxenbury 2 ай бұрын

@@sebs27 yes they can be tricky . It's just getting the Knack . Do you ware boots to start it or trainers . . .I like guys trying to kickstart them in converse boots .i.e all star boots with white socks . ...the xt500 can be the worst if it kicks back

@sebs27 2 ай бұрын

Hi. Bolts and screws will 99% of the time tighten clockwise and loosen anticlockwise.

@redsquare2 2 ай бұрын

I have a CB400F and want to replace the Oil Pan but do not know what direction to UNSCREW the bolts. Before I begin work, I wanted to reach out and ask if you can help out. The engine is currently mounted on the bike, not off and I will be removing the pan with the bike upright. I really would appreciate your help to avoid any errors and potentially stripping any bolts in the process.

@NolanTaylor-e3l 3 ай бұрын

I now own this bike. Sadly it doesn't start like that at the moment!

@sebs27 3 ай бұрын

It was a lovely bike, not mine but I sorted the carbs for a friend. It ran and drove really nicely at the time. The exhaust was the only downfall for what was a very original bike

@Dauddavidai 5 ай бұрын

❤❤❤❤

@plusblood5101 6 ай бұрын

Yes thumbs up You did a miracle with leaking carbs Tap tap and fixed

@3647Edd 8 ай бұрын

Going to have a go at my spare set so this video was perfect, thanks.

@3647Edd 8 ай бұрын

Ideal, thanks fella. Just what I needed to see as my 400 Four has been laid up for about 5 years and will need a thorough recommissioning to get her back on the road. 👍👌👋🏼

@thomasgillis7632 8 ай бұрын

Hi There, did you have any issues with the cam chain tensioner? Thanks.

@duanerobertson8200 8 ай бұрын

😩 'PromoSM'

@SuperResantos 9 ай бұрын

Very cool!!!! I wanna one this😅

@qivarebil2149 9 ай бұрын

Worst repair job I've ever seen.

@sebs27 9 ай бұрын

thank you for your positive feed back

@jdsstegman 10 ай бұрын

I use to use the exact set of gauges. I haded having to sync the gauge set first before using it to make sure the gauges were scync to each other. Like yours, the needles are not the same when at rest. And no matter how careful i was with mine, they never stayed synced. I just left the covers off the gauges so i could get to the adjusters. But i have since switched to digital 6 port manometer. Dont get me wrong. It gets the job done but the more accurate, the smoother at idle they run.

@sebs27 10 ай бұрын

Yes these gauges are very basic as you mention, I have considered upgrading, but I very rarely balance carbs so its not worth it in the long run. Maybe if my KZbin channel takes off one day I can get a state of the art set.

@paulocesarvitti5723 10 ай бұрын

A mesmo nossa xr 200 brasileira

@sebs27 9 ай бұрын

These bikes in South Africa are made in Brazil

@jdsstegman 10 ай бұрын

Been here 3 times so far. I restored 3 1972 cb350's. Now I'm doing 2 1972 cb750's. I chose to bore them paper thin. For fear of galing.gaming. I had new sleeves made. You don't want to know the cost. But you sir are a genius for attempting this!! Never would have thought.

@sebs27 10 ай бұрын

Thank you, I like to try find alternative means to get things done.

@ambersmith6517 10 ай бұрын

AWESOME

@AmirPomen 10 ай бұрын

the damaged broken sleeve is due to previous damage i reckon... broken piston/conrod... u can just buy new c70 cylineder and start with fresh sleeve and not to mention using modern design piston which is plenty available from south east asia motorcycle parts dealer online...

@sebs27 10 ай бұрын

the barrel I used is from a c70

@AmirPomen 10 ай бұрын

@@sebs27 i mean using brand new barrel and on all 4cyl... For them to be all equal in term of piston skirt length/overal sleeve length...

@Dreamer3K 10 ай бұрын

why not press it out ?

@sebs27 10 ай бұрын

its a cast barrel, it doesn't have a sleeve

@IgorPestov-777 10 ай бұрын

Ons Vir Jou Suid Afrika!

@SuperResantos 10 ай бұрын

Very good explanation!!! congrats from Brazil! I don't understand the burp😂😂😂😂 Thanks a lot!!!!

@marlonraulgarciaguevera2172 11 ай бұрын

Linda moto

@marlonraulgarciaguevera2172 11 ай бұрын

Saludos desde Nicaragua

@sten6537 Жыл бұрын

Great that it starts again. I must say the engine has a bad knocking sound. Could be a crank bearing?

@sebs27 Жыл бұрын

Hi No what you heard is a bad exhaust leak (its been repaired since), these bikes have roller bear cranks.

@mrtopcat2 Жыл бұрын

My comment comes too late, but running the bike without battery has a good chance of frying the voltage regulator/rectifier. I have my XT600 for close to 35 years. It is in storage now and I only start it every once in a while to get things moving a bit. But I always hook up a 12V battery when doing so.

@sebs27 Жыл бұрын

You are correct, not only can it damage the regulator but blow lights and so on too. however under idle with a few gentle revs it will be fine. This XT btw has a aftermarket regulator

@andrewdaniels7076 Жыл бұрын

Hope to see part 10 soon! Shes almost ready to fly!

@sebs27 Жыл бұрын

Thanks, there will be more soon I hope. I haven't had a chance to get back to it due to work commitments, but I did get the green light from my AP a month back to basically complete every thing now

@andrewdaniels7076 Жыл бұрын

Looks like a nice little efis unit

@andrewdaniels7076 Жыл бұрын

Just watched the whole airplane rebuild to this point. Thank you for taking the time to make the videos

@cristianvasluianu Жыл бұрын

Hello! Awesome design. How steeper motors move on aluminium extrusions?

@DrazenCika Жыл бұрын

You did a lot of investigation, and great job!

@johnmcgrath8673 Жыл бұрын

Love the simplicity of design. You may have an issue with the spindle due to overheating. That wood bracket is a lot of insulation.

@sebs27 Жыл бұрын

Thank you. so far so good, the spindle is a router and its got a pretty strong fan that blows through it, but I also don't use it for extended hours at a time

@sayithigher Жыл бұрын

Very cool! Where in SA did you order your parts?

@sebs27 Жыл бұрын

thank you. I got the cnc parts from www.3dprintingstore.co.za/

@sayithigher Жыл бұрын

@@sebs27 Cool, thanks very much!

@georgealeong8188 Жыл бұрын

if the bike has a starter it will not work that cdi will only work on a kick start model only

@gusdogbrownlab435 2 жыл бұрын

Darn it I've got one of these to get going. Always wondered why XT 600 owners had one leg bigger than the other

@sebs27 2 жыл бұрын

Its been starting a lot easier now that its been running some more

@ryanhawkermoto 2 жыл бұрын

Hey Baseman awesome project do you have a 34L or a 39E vin number?

@sebs27 2 жыл бұрын

Hi Ryan, Ill take a look in the new year once Im back at my workshop

@sebs27 2 жыл бұрын

It’s a 39E motor

@ryanhawkermoto 2 жыл бұрын

@@sebs27 that’s good to know mine is also a 39E.

@azoz.almala 2 жыл бұрын

Can you share me link store 6:37

@sebs27 2 жыл бұрын

www.3dprintingstore.co.za/centurionstore/product-categories/cnc/cnc-parts.html?

@azoz.almala 2 жыл бұрын

Y do you use v2040 ?

@azoz.almala 2 жыл бұрын

How i can call you plz, i want ask you for cnc

@azoz.almala 2 жыл бұрын

Can i get your plan cnc plz

@sebs27 2 жыл бұрын

Hi. I don't have plans for it. it was built out my head by trial and era

@azoz.almala 2 жыл бұрын

@@sebs27 what is number v-solt

@mounirbee1104 2 жыл бұрын

keep going

@antoniosabin2488 2 жыл бұрын

Hey where you can bună parts for aeon crossland 300

@kangwanashbanda8799 2 жыл бұрын

Hello baseman, I have one of these wanted to know if I need to put coolant or not. Loved the video

@sebs27 2 жыл бұрын

thank you. its air-cooled, no coolant.

@kangwanashbanda8799 2 жыл бұрын

@@sebs27 ☺️thank you🙏🏽

@nedsworkshop9919 2 жыл бұрын

Nice Build, I will have to try a wooden CNC build myself, I have also been following BobsCNC ch. Main change id make and you too can do this is make the bed a tortion box and mount Y rails lower so you have nothing obtructing the sides and you can use it as an asembly table when not routing.

@sebs27 2 жыл бұрын

Yes that would work quite well especially if you are limited for space. It could mean your side posts might potentially flex more as they will need to be longer. But Im sure with a little bracing that could be sorted. thanks Ill look up bobsCNC.

@ericeinsmann5559 2 жыл бұрын

@4:30 This item probably has several names, but I would call it a T-nut. Nice job on the cnc build. Maybe one day, I will build one myself!

@martin-ch5586 2 жыл бұрын

hello baseman, one question, at minute 7; 10, did you start the honda ctx without a battery? Good video

@sebs27 2 жыл бұрын

Hi yes I did start it without the battery, on most these smaller bikes the ignition system works independently. Similar to a magneto system

@martin-ch5586 2 жыл бұрын

@@sebs27 Thanks, do you think I can use the Honda CTX without a battery or is it not recommended?

@sebs27 2 жыл бұрын

@@martin-ch5586 I wouldn't recommend it for a long time, it can blow the lights or damage the regulator eventually

@zoheirsettaf9751 2 жыл бұрын

Please can you tell us what kind of stepper motor you used

@alsaffarstudios 2 жыл бұрын

Creative creation. Thanks for sharing it with us.

Ең жақсы KZbin

Пікірлер