You helped me so much for the life of me.I could not find it

That what she said. 5-29

always keep at least 25% fuel full otherwise dpf regeneration can fail and then you get expensive problems. Agree, the abs plug is in a really daft location.

Thanks , do u have to drain the oil to replace?

Gracias amigo

Can i Drill it out the Plastik or is it to dangerous for the abs Sensor inside

WTF is it with this click bait shit, you did not even say which was best just a crappy 20 min video explaining nothing and showing nothing....?

Just tap it in very gently. Tap tap tap TAP TAP TAP BANG BANG BANG. Once it goes tight, there's no way out. I cleaned the hole out. It's 10mm but gets closed up by the rust.

I have an a problem with my benz c class 202 180 is not selecting gear it used to jack when putting it on gear

All right James, can you send me the link where you got those parts from cuz obviously I know about the eBay situation with the sensors. I've got to do the same as you've done. Be much appreciated where you got the part from

Good video. Thankyou.

My brake pedal sinks after changing the front brake calipers. They have changed the brake master cylinder, they have bled the ABS module with a scanner and it remains the same. I can't find the problem, any ideas?

HI jamie its jake

Thanks

How did you find these fit? I have some and they're not very flush to the arch and doesn't dully fit to the curve of the arch

To many f ing electronics 😂 I wish I never bought a sprinter.

Where does the wire carry on through? I need to remove it completely thanks. Very helpful.

Hi Jamie! Can’t find you on fb doesn’t look like you’re on here much anymore :( hopefully you still see this.. not sure if you remember me but I was driving for Reynolds and had the hydrogen box lifted by you 😁 I started work this week for Road Rail Cranes (RRC crane hire) as an apprentice! So far been on the 30tonner in the yard and been driving the STGO 3 ballast trucks but got my A60 and A40 next week 💪🏻😍

Thanks for video. I currenlty have ABS/ESP codes. Got a genuine sensor from merc to fit but I can see on MOT history that the rear right hub (sensor I get codes for) has minor leak so wondering if this is the root of the sensor failure so looking like I may have to replace hub. Just wondering how you seperated hub from half shaft as I know people normally take them out together and seperate on a press. Much appreciated!

Great informative stuff Jamie, did you end up buying a new Mercedes hub? I replaced my half shaft recently with an eBay one and I've got the three dreaded yellow warning lights, any pointers in the right direction on parts you bought to cure the problem would be greatly appreciated. 👍🏻

Good video, but man. You f***** u* with all that music can hear Nothing.

My emergency break was left on while driving and abs came on after it hot way too hot replaced sencer still not right will the ring possibly move to cause my problems due to excessive heat

Rust jacked and lifted up away from the reluctor.its best to drill the fat bit with the o ring out as thats whats stuck.the narrow bit at the bottom is usually loose

Thank you for the video. I have same problem. Been driving like that for a year. Now Be trying to fix it.

I have same problem. Can’t figure why. Swamped with new sensor. Checked wiring is good. Just not picking up reading off hub.

Thank you for a great video and informative information

So was this a Vs video or a 20mins of waffle?

Good video

Hey bud what are the symptoms? I'm in limp more code 2359

hello so is this the internal air temp sensor or is there another 1 ? my van goes into limp when it is hot and restarted i was told its the engine air temp sensor

What be a symptom to replace it

but where is it near the radiator.

what about 2017 sprinter?

yes, that sensor does not work, can bus won't pick up on it, not sure who sells aftermarket one that works right, let me know if you find out.

Interesting, ive got a 2022 519 and have this annoying rattle coming from underneath, straight from the factory. Its been driving me nuts. I'll check underneath for this!!

How man kits did you need to do the whole van mate. Cheers

So, which one do u recommend? I can get here in Romania, Raptor with 31.5 euro/L or MIPA liner with 22.5 Euro/L. I need around 7L so overall is a big difference in money. So is it worth getting Raptor?

Good video thanks for the information

🤧

I had to take an angle grinder to mine too 😂 needless to say anti seize was a plenty on the face of the hub for the new disc.

Same problem

Mess

I’m looking to install a oil pressure sensor on my 2011 Mercedes GL350, but I think ima Drill & Tap some threads into the Aluminum Oil filter Housing to accept the oil pressure sensor.

The criss cross bit is the 🐈 🤣🤣🤣🤣. That's a flexible joint to the rear silencer 🤡 🤡🤡🤡🤡🤡

hey, where did you buy the trims? thanks :)

Love the vid and the music is a nice touch. My sprinter haa a blocked dpf which i havent sorted yet. Thing is soot in the dpf is carbon. It doesnt burn off! Ive a vid on different chemicals to clean the soot off and it looks like dish washer tabs or coke is best. It seems like detergent can get the soot to detach from the dpf. Im not sure but the smoke you see from these dpf cleaners is just an oil additive in the cleaner that generates the smoke. Its also interesting that dpf helps the enviroment but just blows it out in one lump .. somewhere else !!! Anyway liked your vid and views under the van, which is where i have to go now. Chemicals or lump hammer. Not sure yet

well done jamie 🙀🙀🙀

Why is there music?

Your damn music is so loud it's hard to hear what you're saying dude

Hey Jamie!