It was better, few hours extra. But it was hard to notice as it was not significantly different.

No, steel

Steel with a rubber over mold

Are there drills in the market that can do it? Unfortunately I haven’t tried other drills

Thanks. Those clips will be open when you stack multiple toolboxes.

@@LearnTogether101 Many thanks for your very speedy reply! Mystery solved 😄

Around 3kg

Yes, it is possible, I tried few times. Hands get tired if the weight is not balanced properly, but it works well. Good luck with your project.

@@LearnTogether101 great!! Thank you very much my friend!!

για να ειναι πιο ξεκουραστο πρεπει να το συνδεσεις με μια καλη ηλεκτρικη σκουπα για να ρουφαει και την σκονη ,στο ταβανι αυτο ειναι πιο καλο

@@zodiac7koproi σωστος!! παντα με σκουπα γιατι αλλιως θα εχει υπερβολικα πολυ σκονη.

@@zodiac7koproi 1. Работать такими машинами нужно ТОЛЬКО с пылесосом! 2. Пылесос должен быть строительный, с автоматической очисткой от пыли. Или с отдельным циклоном. Простой бумажный мешок или фильтр обычного пылесоса забивается пылью за несколько минут. 3. Нужно проконтролировать параллельность тарелки кожуху и вылет щёток вокруг тарелки. Щётка должна на пару миллиметров быть ближе к стене чем наждачная бумага. При необходимости отырегулировать положение кожуха. 4. Наклейте на кожух вокруг щёток малярную ленту (малярный скотч) для ограничения подсоса воздуха. После этого машина будет работать отлично.

yeah it sucks to have massive rooms in our houses to paint

Pas besoin de parler si tu sais lire.

😊 still a nice saw for DIY work

Thanks, I used motorized sander first ( Parkside sander, see my other video) to remove all the texture, then apply one layer of mud followed by painting. For me the above process gave a smooth wall. Hope this helps.

Depends on whether you have the time and muscle to do the sanding manually. Texture can be quite tough to smooth out. I have 2 days. I need to get the whole room ready for skim coat.

Sure, from my experience if the sanding is done properly to remove most of the texture, then you dont need multiple skim coats. I just applied one skim coat and sanding with fine grit >120 gave a smooth wall ready for painting.

amen sister! skim coating is no joke. def not an easy process

Very true. I have asbestos ceiling in my garage that I have to remove at some point 😊 Thanks.

In California it is required to have a survey(test) completed before scraping any material that might contain asbestos. Scraping without knowing will contaminate the interior of a building. Won’t put my family at risk. But I get DIY and budgets. Lol.

See end of the video or here Dewalt saw (free drill) from Coolblue.nl kzbin.info00pmYb60NqY?feature=share

Dewalt saw Coolblue.nl

Bought it from Coolblue in the Netherlands.Not sure about promotion in the US. 😊

Link cool blue

I observed shaking when 1) on rough surface 2) after changing the sand paper. Just start with almost no pressure applied, when the surfaces makes good contact in a minute, then apply pressure, it should work. Hope this helps.

My surface was not rough as yours. Also it’s really shaking bad when i put a little pressure. The only actual way to make it possible is not put pressure at all and i’m not sure about the contact, or pressure a lot and that makes it so hard to do the job. I’m thinking some piece of the item is not balanced or is misaligned. If i don’t figure out the fix i think i’m going to return it even if looked good for all the rest.

I have sanded around area of 30m2, so far going good. May I know your experience? Thanks 😊

@@LearnTogether101 after 1m2 there was no improvement i had to do the job by hand

Esta máquina son para los que saben usar Realmente una máquina... adaptarse a la máquina, no presionar demasiado , saber equilibrarse con la máquina. Si lo quieren todo fácil entonces comprense una festool Yo estoy contento con la parkside muy buena máquina y se trabajar con ella.