Yes 👍🏻

Yes once its paired, it will continuously Paired, even you will Turn Of and On, as long as you did not press pairing Button that cause to disconnection.

@@vincheeseeeee di ko sure boss pero tingin ko hindi, it looks similar lang

I'm not using MG12xu but as per my experience with Mackie ProFXv3 series, it's amazing and I'm happy

AS per Error you mention its is related to Trailing Cable, and 86.01 has related to Carriage, machine detected that there is a Jam due to Movement friction occur, you need to do the Service Lubrication

@@aarifhussain6688yes just remove the Hot Swap Fault HDD and just insert the replacement HDD, one you properly plugin, Done! Leave it and let the System do the Rebuilding and it take bit of time it depends how big is the data, once rebuilding is complete it will give u Green led and synch with each other.

@MHIKSTV ok thanks so can tell me that I have 5disk in My Fueson star Storage and configured with raid 5 I want to just check and test drive that is raid 5 confirmed or not After insert and remove drive then my other Drive will or not ?

Just remove the left and right Cover, remove all wiring connector and the motor, then remove the 4 T15 screws, note the whole rear if Hook both sides, to be able to removed, you need to carefully lift. ( by the way before removing the rear assy. what is the issue of the machine? )

@@MHIKSTV Thank you for your quick response, in fact this machine has to change location and unfortunately it does not fit through the door which is 90 centimeters wide and is too small.

@ there is an option also but you need man power. Just remove the stand and lift the machine then put it back once you securely out the machine, one time it happen to me the machine is in the 3rd floor Site Office to relocate also to other site, its not Fit in the Door, the only way to fit through the door is to Remove the Stand and Lift and do tilt vertical . I did that with the help of at least 4 person 🫣😀

@@MHIKSTV Ok, there is no risk that the ink will spill? because I work with canon and with them you must not tilt the plotter by more than an angle of 15° to 20° otherwise the ink will spill

@@germinalcarvalhoalves1542 Before proceeding, please ensure that the service station is not full with spill-prone ink. If there is No, just simply remove only the six inks while leaving the print heads in place, because removing the PH will require recalibration and alignment.

So far until now no issue, its works fine and clear Audio and realtime.

Tumatagal ang batteru nya at very clear ang sound at real time.

@@diegopadernos1255 boss reset lang ulit tpos pair mo siya ulit by pressing pair button sabay sabay tx and rx for at least hold 5-10 secs. Then release

@@orglidi as per the error you mention its like related to Scanner Bar.

@@MHIKSTV this is a few things that i try to fix 1. replace printhead 2. clean & reseat scanner bar 3. replace scanner motor. 4. reseat all cables & flexsible cable.

No it will not disturb other like i have another separate 1tx and 1rx plus 1tx and 8rx it works fine and clear

@@MHIKSTV Great, thanks

@@mrHegawelcome

​@@MHIKSTVwala po na disturbances sa mga receiver? Planning to buy and with same set up 1 tx and 8 rx

Sir na test ko 30-40M open air realtime parin ang at walang delayed

So far i tested with Max of 8 only

@@MHIKSTV what I mean is how many transmitters can operate in one place simultaneously, not the receiver

I plan to use the WP-10 as a personal iem for musicians and singers on stage

@@asrock7947​​⁠u can aasign 1 RX 8 RX in One Group like what u saw on my Video. If u want another set or group of TX and RX then Pair then Together as a new Pair Group with a Same Source.

@@asrock7947same here its very clear sound and Wide signal Coverage

@@handokodfatikno4050 yes! Same what you saw on this video, and so far until now its still stable connected with a fantastic clear Sound.

@@blindmetoo just press the Pairing button until ot turn blinking red together with transmitter and receiver together or simultaneously

@@KarlRecto-d2m yes boss pero so far limited lang part nyan, pero available ang part mismo sa honeywell, sinusuply lang kasi nila sa mga Autorized service center. Ano po ba Sira ng unit mo?

Boss ung laser nya nagmalfucntion....

@@samuelramos4333 QC sir

Sir Ideal for In Air Monitor yan, kung gamitin mo sa Speaker, meron ideal for Speaker or for Audio transmission, but In Air Monitor theoretically working convert mo lang cable

@@MHIKSTV may model ka recomend? thanks in advance

@@jericlee1509​​⁠sorry sir wala ako ma e recommend sayo, di kasi ako nagamit ng BT for Audio

@@BDM311 you can simple pair the tX and Rx by Pressing the Pair Button together simultaneously

I don’t recommend to buy this product battery will not last ang its not friendly user, and its getting bit hot

@@MHIKSTV ok, very thanks

Yes your audio source should be coming from mixer, if u get it from live video and audio will seconds delay.

200$

Pwede 5 Lang i pair mo at yung the rest i pair mo naman sa ibang Transmitter it will work, reset Transmitter lang yung Transmitter para ma add or ma eliminate mo yung pair nya at ready to accept new device to pair.

You can Switch Mono or Stereo Audio Sound Sir, at very Clear, and it take approx 4 hours ang battery life. At 30mtrs open area. Kaya kung nag Banda ka the best siya gamiting In air monitor Real time

@@MHIKSTV thank you for the informative response, sir!

@@_odiawelcome

200$

In air monitor for Music or Live band or any related music hearing device

Monitores para músicos. Y cantantes

Should be 1tx and Group of Rx at a time lang po. Hindi pwedeng Tx to Tx

Sabay sabay mo e press yung Pairing botton ng Receiver and Transmitter para para mag synch.

@@MHIKSTV Thank u sir

@@daddypchannel2079 welcome

Calibrate mo lang sir sa Service Mode.

Thanks, please like n follow ☺️

Yes u can but not as good as plotter for graphics of PS models, that plotter was design for printing CAD drawings

Di ko maramdaman sir yung latency kasi. Realtime time naman siya

Yes

O vídeo mostra sua pergunta, faça uma pergunta mais inteligente moça 😂

Pwede mo ihiwalay mag group ka kung ano ang i ppair mo na unit sa transmitter then other namang group sa isang transmitter baman ikaw mag decide kung ilang receiver per transmitter

@@MHIKSTVworking po ung ganito natry nyo na sir?

@@JeffreyBarronyes sir working in a veryf good clear audio transmission

I have a supplier on that product coming with complete set, mostly u can buy that 1tx with 2-4Rx

this idea is not possible to Pair with multiple TX in 1 RX