Shame your chuck is a bit naff. "New Boxford" is a misnomer. Yours is probably like mine over 60 years old. But working really well. Good Luck with your machining adventures. 😀
@RustyInventions-wz6ir7 ай бұрын
Just found your channel and Subscribed. Nice work. I have to make a plan securing mine as well
@colmmooney51187 ай бұрын
Super job I’m starting one myself tomorrow the same voice what make of paint was that if you don’t mind thanks super videos keep them coming😊
@hansbromwich9 ай бұрын
I’ve got the same machine, but the lead screw and feed have stopped turning, I guess the shear pin is broken, any idea where it is located and how you repair it?
@hansbromwich10 ай бұрын
Any chance you could explain how to renew the lead screw shear pin on the viceroy lathe please, mines broken so needs to be replaced
@redcruben Жыл бұрын
would you do a video on how to oil and grease the headstock on the viceroy, I can find no info on it and when I oil the 2 oil points on the top I get about half a squirt in then it overflows. I don't think this is enough
@jakarwahh8142 Жыл бұрын
What type of toolpost sir ? I also have the same boxford type A lathe
@Jacob-64 Жыл бұрын
Use WD40 with aluminium your finish with be much better plus the chips wont still to the carbide tool
@mactruck18822 жыл бұрын
Nifty idea that
@seamusbolton2152 жыл бұрын
Well done, hope you have many hours of enjoyment
@mactruck18822 жыл бұрын
Good score on that chuck aswell! If you can get a 5inch aswell it would be worth it. But at that price you can't complain.
@mactruck18822 жыл бұрын
Good job on that
@ronitsingh852 жыл бұрын
You are right on the older machines being better. Find a good low run time unit and man you are pretty much set for life
@ronitsingh852 жыл бұрын
Amazing score on the lorch, did not know lorch made anything apart from their watch maker lathes! Such a jewel of a machine, I would get it just for that and drool over the precision cross slide and the beautifully machined hand wheels!
@johnnybbgunner21362 жыл бұрын
Are you considered a felon now?
@norfolkworkshop36092 жыл бұрын
no not at all, perfectly legal to strip and adjust as long as you keep it bellow sub 12 in uk where i am.
@johnnybbgunner21362 жыл бұрын
Never heard of such a thing!🇺🇸 Tamper screws.
@cristianpopescu782 жыл бұрын
True!👍Thats why I love old Tools.
@RustyBoyCrafts2 жыл бұрын
Nice work
@bjl10002 жыл бұрын
Instead of grinding the handle off, why not turn it upside down and use the hinged lid as an access to remove the ashes? The bottom, now on the top, could be used to cook on.
@bjl10002 жыл бұрын
Instead of grinding the handle off, why not turn it upside down and use the hinged lid as an access to remove the ashes? The bottom, now on the top, could be used to cook on.
@stevensimons46772 жыл бұрын
Wow, years since I used one of these, is there many pple on..? Is it still 14 for a copy + 19..? And do pple still talk in that way these days..🧐😅😂🤣
@jasonwoods4811 Жыл бұрын
It's just 19 nowa days :D
@adventureswithrick80322 жыл бұрын
My 50 cal ammo van has been ordered.
@susankelly77782 жыл бұрын
Have a look at ''My Tiny Workshop'' and his restoration of a Record no5 vice restoration.
@budwilliams65902 жыл бұрын
I predict you will be disappointed by the rivets.
@norfolkworkshop36092 жыл бұрын
Been fine so far.
@piclife11782 жыл бұрын
I own a 8x16 Chinese lathe I bought in 2005. At the time it came with a stand, 2 chucks, faceplate and steadies for £560 delivered. It has been well used and abused but still gives excellent service doing all I ask of it. I have made 5 internal combustion model engine on it and while I can see it is not finished to the standard of Myford etc, it is a tool that gets the job done. The hardened ways show no sign at all of any wear even after 16 years. I wanted something I could move on my own. I have considered ML7 over the years. The biggest thing that puts me off is the generally non-hardened beds used on the Myford. Every time I get interested and look around it seems there are so many "paint re-furbished" examples of 50 or more years old that the risk of paying good money for a nice looking machine but with worn out beds seems high. I am not even convinced they are as good as claimed, the only Myford thing I have is a vertical slide which uses a main nut that is just a complete joke, 4mm thick of some white metal that really doesn't seem fit for purpose at all. I am pretty sure, if it wasn't for the Chinese lathes bringing the overall price of lathes down then I would never have been able to afford a small lathe at all.
@RobertAdairWorkshop2 жыл бұрын
Really like your boring bar. I might make a similar one for my lathe.
@FT4Freedom2 жыл бұрын
You can use a 1 gal square solvent can, wire and tin cans for ducting and sheet. A wood mallet, hatchet and camp knife with old nail to cut the tin and punch the holes. Wire can be used to attach everything together. Definitely want a multi tool. But a basic hobo stove is cheaper than dirt to make with things from the trash. All sorts of steel boxes around.
@Monuments_to_Good_Intentions2 жыл бұрын
Awesome stuff you are doing. I have been collecting toolls.
@martinolesen99302 жыл бұрын
Could you please provide link?
@norfolkworkshop36092 жыл бұрын
ebay item number 362789971321
@martinolesen99302 жыл бұрын
@@norfolkworkshop3609 thank you very much.
@madeddiesman-stylemonsterm66622 жыл бұрын
I agree that things are just not made as well as they used to be. I love that my lathe is a WWII era machine. Thanks for sharing this! kzbin.info/www/bejne/sJ6yg4xua5aMa7c
@2Steppa22 жыл бұрын
Not bad here in Suffolk either.
@MakerMike-bx5ms2 жыл бұрын
Would be able to provide a link for this vise. Thanks much!
@madguernseyboy2 жыл бұрын
I agree link please :)
@norfolkworkshop36092 жыл бұрын
ebay item number 362789971321
@machinenutdel67642 жыл бұрын
That looks almost identical to my Smart & Brown model L, please send me all your collets , Del
@seamusbolton2152 жыл бұрын
Hi there, excellent video, love the old machines Can I make one suggestion however ? I know these old machines can be picked up for very little money, but sometimes I think this is a false economy If you can pick up a more modern Student / Harrison 300 etc with gear box and modern cam lock head stock and higher speeds for carbide, do buy it Yes you will pay 3-4k, maybe more, but a good one is a pleasure to use and if you take care of it you can use it for 10-15 years and sell it for more than you paid for it (what car or other gadget can you say the same about ?) Thank you again
@norfolkworkshop36092 жыл бұрын
i compleetly agree but theres a big differance between £100 and £3000
@seamusbolton2152 жыл бұрын
Hi there from Ireland Just discovered you channel and looking forward to binge watching all the rest of your videos Big fan of all the usual suspects, doubleboost, Abom79, Keith Rucker .... etc I have a little Colechester Student myself, but don't use it as much as I should Thanks again for all the effort it must take to make and upload these videos
@mw2mastersash2 жыл бұрын
Pull the transformer out of that power supply and rewind the secondary output with some 6mil panel wire with about 14 turns and increase the amp output
@Decrepit_biker2 жыл бұрын
Yes that is a factory filler, which lots of people don't realise!
@terrytrooper22542 жыл бұрын
glade your happy with it mine is very good at bringing in rubbish
@deedeeindustrialsuperprecision2 жыл бұрын
Nice little machine, a little like the early LeBlond regal
@deedeeindustrialsuperprecision2 жыл бұрын
I like your videos but, I think you are being too kind to the new mini lathes and such, the new smaller machines I see over here are pretty terrible. Your Colchester is a serious machine. I use an old worn machine like that all the time, you get to know where the "sweet spots" are.
@deedeeindustrialsuperprecision2 жыл бұрын
That is a great machine! The quality stands out. Thanks for showing.
@deedeeindustrialsuperprecision2 жыл бұрын
This is a great video! The points you make are right on. The new manufactured machines we get in the US are usually very poorly made and designed, until they get into the larger geared head machines. It really is a tough decision to make buying new vs old. I found where I am located, taking a little time, really good solid old lathes can be found at much less cost then new. Small older machines are in short supply, and expensive.
@melgross2 жыл бұрын
Well, it depends on the old lathe and the new lathe. If you compare an older lathe that was built and priced expensively against a new lathe that’s built and priced cheaply, as long as the old lathe isn’t worn out, which is often true, then yes, you’re correct. But you have to be careful, because a lot of old lathes are definitely worn out, and need a lot of work to bring back to useful working condition. But you can get pretty high quality new lathes today that aren’t TOO expensive. They tend to be more versatile. The truth is, I have a South Bend 10L Heavy I bought in 1983, and a South Bend FOURTEEN I bought in 2002, so I’m not against older equipment. But I’ve been doing this since high school in the 1960s, and can repair old equipment if I have to, and bring it up to standards. New people to this can’t do that as they don’t have the knowledge, experience, so it might be best to buy something new, unless they know someone who can help then pick a decent used one, and possibly help to get it in shape.
@danharold30872 жыл бұрын
Its a time vs money thing. If you have the time to put into an old lathe it generally will be the better choice.
@melgross2 жыл бұрын
@@danharold3087 it’s more and experience and knowledge thing. People starting out don’t have that.
@danharold30872 жыл бұрын
@@melgross Also true.
@ronitsingh852 жыл бұрын
Man I hope folks have the patience and love for these older machines to go the extra mile to bring them to issuable condition. The thing is they were designed to be SAVED, most of the bearings you can replace tc but as for the ways, I doubt you can :-( . There is such romance with older machines! Love them.
@melgross2 жыл бұрын
@@ronitsingh85 I do t think people understand the philosophy of the reason things were made the way they were, and the way they are. A ways back, very few things were really good. I mean bearings iron, steel, and the understanding on how to use it wasn’t really there either. All of that became to come together around the early 1930s. Designs began to change around then. But even later, in the ISO’s, with numerical control, manufacturers began to s ee that equipment wasn’t going to have to last to years, because advancements were coming too fast. Companies got rid of machinery every 15 to 20 years instead of every 20 to 40 years. Computer aided design and more knowledge of materials also meant that less metal could be used. Heavy formed steel bases are just as good as iron ones, and much cheaper, so that came around. Why use a heavy iron cover,mwhen aluminum is just as good, and cost less, etc.
@craigtate59302 жыл бұрын
I am all about the old machines, especially unusual stuff, or things that stand out for some reason
@peterparsons32972 жыл бұрын
I own an old Colchester Student lathe, recently bought a import 9 x 20 lathe for smaller jobs, this was not a cheap purchase. the quality of construction and assembly was awful. headstock badly out of alignment tailstock 3mm too low, gearbox no bearings just steel against steel. luckily i had the equipment and experience to rebuild it, but without my mill and big lathe it would have been good as an anchor.... no support from the company i purchased it from. if i could have gone back i would have gone for an old british or american lathe
@norfolkworkshop36092 жыл бұрын
Unfortunately that's all too common
@peterparsons32972 жыл бұрын
@@norfolkworkshop3609 its amazing the colchester is older than i am and still more accurate than the import.
@norfolkworkshop36092 жыл бұрын
@@peterparsons3297 I completely agree the fit and finish on them is just not up to scratch and Evan after fettling them they just don't give the results of a older machine.
@melgross2 жыл бұрын
What lathe was that?
@peterparsons32972 жыл бұрын
@@melgross my import was from Chester Machine Tools, wasn't cheap either, when i reported problems i didn't even get a reply at first then they sent me a parts / price list. at one point i was very close to stripping out the motor and just scrapping the thing. i wanted a smaller lathe for the shop not a project
@zukispur54932 жыл бұрын
Keep on keeping on keeping the thing alive bruva. 73 from tottenham London.
@28gwdavies2 жыл бұрын
No one can hear you. You need to watch the video before you upload it, the quality is terrible. Such a shame as the content could be very interesting.
@norfolkworkshop36092 жыл бұрын
im aware the sound is horrendous, didn't realise the mic was knackered till i came to edit it unfortunately
@davelowe19772 жыл бұрын
The sound is very very quiet. Very interesting project though!
@norfolkworkshop36092 жыл бұрын
unfortunately i dint realise the mic was kaput till i came to edit it together
@ionmanoiu22412 жыл бұрын
Nota 10 pt. cuțit ! 😁
@ianmangham45702 жыл бұрын
The bloody faffing ya gotta do just for stock removal lmao, they treat us like savages lmao