Where can I purchase these light brackets from??

Hello, please tell me how to reset the first calibrations that you do immediately after flashing? I changed the firmware to 0.6.1 and did the calibration incorrectly... and now I can’t fix it, and I can’t upgrade to another firmware either.. can you please help me solve this problem?

You Brits are NUTS!

WAY TOO MUCH WORK for features that SHOULD have been by HENG LONG!!

Man I love that set-up you did an awesome job .I would love to be able to 3D print the chassis deck plates nice job !

Great video. I recently Bought a second hand SCX10 iii gladiator and currently in process of rebuilding the drive line with brass and Aluminum parts.

can we see these hobby conversions on the track? It's a bit of an anti climax after all that work to just see it roll back and forth on a desk.

He’ll do you know where I can get the running light mounts from many thanks

Hi. I have a s15 tt01D chassis. All basic parts. But how do i convert it to 2wd? Do i remove the middle shaft? Is it advisable to remove it and convert it from 4wd to 2wd for better and proper drifting ?

Can I purchase the printed parts from you

Can you change the tires ?

I just bought the same wheels and tires for my clod Buster I'm having a terrible time figuring out what size the screws those are are those the M2 by 16 ? And would that be a 3.5 mm allen wrench ? Thank you I love your videos

Is latency changed?

Love your videos brother I just purchased these tires and rims today I think they're pretty awesome and I was a little confused with the adapters but I had to come back and watch your video again and you say it comes with a set of adapters already the medium ones ? Because I just had a thought I hope they will bolt on my clodbuster

Good post, interesting telemetry. Some comments from an own-design, extreme aerobatics flyer: 1. It being an Acrowot you will be "going vertical" at some point. You need to be able to hold that model vertical for at least five seconds without it dying. Most likely it will need to be a couple of clicks richer. If you don't do this you risk a dead engine and subsequent deadstick when you close the throttle for - say - a stall turn. 2. You didn't, I don't think, turn the engine over (anticlockwise) to check the (inverted) engine wasn't hydraulically locked - BEFORE connecting the glow driver. 3. With an inverted engine most "flooded" problems are avoided if the glow driver is left connected for at least five seconds before applying the starter - to burn off fuel that has collected around the plug. Obvious really. 4. You are using an old model Master Airscrew prop. These are flexible and not efficient. APC props are much stiffer and much more efficient. Also, and this would appeal to you, APC publish very comprehensive performance data on every prop they make. Using their tables and the rpm you measure, you can work out the static power the engine is making. 5. The APC prop data shows that their props are most efficient when flying at "pitch speed" - with the prop aerofoil at zero angle of attack at max model speed. Looks like you'll be flat out at about 65 mph. Say you're prepared to run the engine to 10,000 rpm. The required pitch is 7". (I'll leave you to check that!) The lower the pitch the noticeably better is the model acceleration and vertical performance.

Damn, that artwork is excellent. But like all black paint the dust and fingerprints shows up big time.

Fantastic video. I built and flew a yamamoto, back in the mid 80’s. Your video brought back memories - when you spoke about the excess castor, the elastic bands holding the wings and also the main wheels. Fantastic. It was so basic, but yet so simple and stable.

I'm guessing from the long pause that things didn't go as everyone would have liked. I'm truly sorry if that's the case. Rest assured that we subscribers (certainly most of us) DO care and wish for the best for all that we follow and I for one hope to see you back on here whenever you are ready mate.

Just wanted to say I've always enjoyed your content, and truly hope you're doing well.

Dude, Ive messaged you on Discord, if you get this, want to catch up, thinking of you

did you do any extensive programming for the sehifting servo?

Has anyone got the instruction manual they could send me a copy please.

Just amazing work

Awesome looking rig!!!! I am just finishing up this build, and went a lot simpler with the paint scheme, even muddling it up a bit to make it look a bit worn. Also, with the REALLY dark tint, I will likely only put the dash in. One thing I don't like is the battery placement, and will likely move it into the cab. Also, none of my batteries will fit in the existing tray, so I will design and print up a tray to inside.

nice hint with the lucas game "the dig" haha

The one thing I have found about the Tamiya threadlock: it does not damage plastic. I tested it by putting it on a piece of sprue for a week, and no discoloration/melting/brittleness.

All done. Thanks again.

Superb again. Thank you. On to the next bag!

This is awesome. Thank you so much!

2 bitS,, 4 bITS,, ADOLLAR,, ALL FOR THE LIMIES, STAND UP HOLLOR,, A FEW BITS MO,,, LOL

All the best bud, hope everyones doing ok.

Hey dude, hope you are okay. Your videos have inspired me ever since I took up RC about 6 years ago and also very relaxing watching them. All good things! Miss looking forward to the Sunday videos but most importantly, hope you are okay!

I just bought s this, how many channels would you recommend to the receiver

Nice video, thanks for posting it! Mine has a Tower Hobby two stoke .61 glow engine.

I wonder if this would help with my problem of the radio resetting the servo reverse settings on channel 1 and channel 2 from time to time.

Had to use 3 differents stlink dongle to have a working one. Tried 3 pc, 2 flysky gt3c to realise maybe the usb interface was in faulty. Thank you for your tutorial

To completely remove the tape from the sunshade, you can remove the topper from unclipping the two clips in the inside cabin (on the roof). Then sliding the whole topper forward to remove. Once the tape is removed from the sunshade, you can re-attach the topper by sliding the topper on from the front of the van to the rear (topper rwill click in). HTH.

Could you open CCVT and make video about it? I found manual with CCVT parts diagram, but I still have no clue how it works...

I just built this car and it was my first RC car. It was so much fun making it, before I got to page 7 I had gone and brought four more tamiya cars 🫣😅

Definitely not taking advice from a guy that can't properly put on a screen protector. This radio is for who ever wants it. you dont need to be a scale, trailer or crawler hobbist to get anything us out of this radio. If you like the tinkering, programing, computer side orof the hobby this is it. If you just want to pick up a radio and just drive we'll you wouldn't even be watch this video just stick the rtr transmitter or stick to toy grade rcs.

Amazing

Just seen this, take care and best of wishes to you and your family...all the very best.

Hi, is this model capable of doing high speed snap rolls without breaking anything?...

whats the ts code of this color?

Did you ever post the 3d print files for this

Shaft Retaining Compound, or JB Weld would work well also..ask me how I know.

best wishes for your father

well impressed with the wiring .my r620 looks like a birds nest compared to yours ,also where did you get or how did you do the opening side skirt

nice work :-) what brand is your small electric screwdriver?

Family comes first mate, stay safe, take care