Жыл бұрын
Пікірлер
@Hasangirişim 9 сағат бұрын
meraba mazeme listesini ve diğer tüm gerekli şeyleri bana yaza bilirmisin bende yapıyım
@fernandopenna978 4 күн бұрын
Thank you for the video 👏👏 Can I just ask a question? I am trying the same thing with Rex C100 + SSR DC-DC to control the heather cartridge from an old 3d printer, but when I turn it on, it gets hot too fast while the thermistor is showing 30 degrees celsius, with fear of burning something I turn it off. I am still trying to understand what is happening, have you had this problem, is this normal?
@3Delite028 4 күн бұрын
If you already have old 3d printer than there is no need to buy rex c100 , just use the motherboard provided in old 3d printer to control the nozzle temperature.
@SUMANKUMAR-cy8qc 9 күн бұрын
👍👍
@3Delite028 9 күн бұрын
👍👍
@sametsahin01 10 күн бұрын
Nozzle kac mm
@3Delite028 9 күн бұрын
1.5mm nozzle diameter so that filament can go even in bowden tube extruder setup
@pranavchavan9763 25 күн бұрын
Pls show the rex C 100 programming part too
@3Delite028 24 күн бұрын
It doesn't need programming.. Just connect the wires as per circuit diagram and you are good to go...
@pranavchavan9763 18 күн бұрын
@3Delite028 thx
@pranavchavan9763 9 күн бұрын
@@3Delite028 I have done that exactly as per the circuit,but the heating element is not working
@fernandopenna978 4 күн бұрын
@@pranavchavan9763 , I am not good with electronics but I had a similar issue, not sure if is the same root cause tho. Check if your SSR is DC to DC, the one that came with my Rex C100 was DC to AC
@AhmedHassan-wn3nc Ай бұрын
what 3d Printer dimensions
@AhmedHassan-wn3nc Ай бұрын
and linear rail shaft
@3Delite028 Ай бұрын
I have used 500 mm lenght linear shaft of 8mm diameter And accordingly the linear extrusion frame 480mm
@bharatbhaipatel6803 Ай бұрын
❤
@officialprinters6744 Ай бұрын
Sd card not working 😢😢😢😢 help me
@3Delite028 Ай бұрын
Check in the video Enable SD card If that is not working then there might be some issue with lcd controller
@officialprinters6744 Ай бұрын
@@3Delite028 ramps1.4 is problem I changed ramps 1.4 now its working
@Chicong2007 Ай бұрын
Help meee
@3Delite028 Ай бұрын
Please see connection diagram given in the video
@Chicong2007 Ай бұрын
How to setup C100
@3Delite028 Ай бұрын
See circuit diagram. Make sure you have correct connection. Then its very simple Use arrows to reach to desired temperature. And set key
@Chicong2007 Ай бұрын
Please tell me how to adjust the temperature😢😢😢😢😢😢😢😢
@3Delite028 Ай бұрын
You have to adjust the temperature depending on the type of plastic being used. Amd few trails because it depends on how you have set up the temperature sensor. You can try from approximately 140 degree Celsius and try to extrude filament. Then go on increasing and decreasing temperature based on how well filament is extruding
@reiniertl Ай бұрын
Didn't show how to join a 2020 to a 2040. Just 2020 to 2020
@3Delite028 Ай бұрын
It can be done in similar way. Drill the hole on 2020 , tape the holes of 2040. Use M5/M6 nuts depending on the diameter of profile hole.
@Chicong2007 2 ай бұрын
Hello, I'm Vietnamese and I think this idea is very good. Can you help me with some problems?
@3Delite028 2 ай бұрын
Yes would love to, but after 1 week..
@Chicong2007 2 ай бұрын
@ Oh no, I have to finish this product by December 7th, can you spare a few minutes?
@Chicong2007 Ай бұрын
@@3Delite028 hello can you help me
@kalpana-sts 2 ай бұрын
Can I us ssr 25DD, 12-220 VDC instead of 25DD, 5-200VDC
@3Delite028 2 ай бұрын
Yes as long as current does not go beyond the limit of components specification you use
@EvaristoOrtiz-dt8sg 2 ай бұрын
hola amigo necesito de su ayuda estoy cargando el marlin en la ramsp 1.4 pero no he podido compilarlo me da herror me sale que la depuracion no es acta para el mega 2560 de arduino
@3Delite028 2 ай бұрын
There may be many type of errors while loading But what error is appearing on screen You mark that and try to search how to resolve that error code online. This might help Or try to mention here what error code is generated
@mariodelgado6242 2 ай бұрын
thankyou very much!! I will do this project with my 11 years old son :)
@3Delite028 2 ай бұрын
Great, have fun with your son! 😊
@AnkitKumar-dj5my 3 ай бұрын
From whre do i get the things z
@3Delite028 2 ай бұрын
Can you please specify what exactly you are looking for??
@AnkitKumar-dj5my 3 ай бұрын
I have a doubt Can't i use ESP 32 WR ROM BECAUSE IT IS FATER THAN ARDUINO UNO From India
@3Delite028 3 ай бұрын
If it is available with ramps 1.4 like shield then you can try.
@Hasangirişim 9 сағат бұрын
@@3Delite028 kullanılamaz çünkü arduiniou mega gibi arduiniou uno veye esp modellerinin yükleme kapasitesi aynı deil ve bu marlinin kapasitesi daha yüksek ve mega hariç dier modellerde geçikme çk yaşanır
@ZaherHashem 3 ай бұрын
Thank you dear, the end of k thermocouple is bigger than its hole in the metal cube. Can the hole be enlarged?
@3Delite028 3 ай бұрын
Yes i have enlarged hole of the block. Make sure to have tight fit Not too loose..
@richardtapia6791 3 ай бұрын
Hello friend, I hope you are well ... look, I have a problem with the screen, I do work correctly the screen when I connect the usb to the arduino with the ramp 1.4 and I can use it, but when I disconnect it and I want to connect the 12v power supply, the screen turns on, but I do not get the characters, I only get the squares, I try to set the contrast .. but nothing, it does not work. Why is it that causes me that failure?
@3Delite028 3 ай бұрын
Bro this happened with me also. When i used original Arduino megha 2560. The screen goes blank as soon as it disconnected from PC/desktop. When i replaced my Arduino megha with old one it worked. I don't know how, and what went wrong with original one... Still Do not know the solution but Make sure you power it through USB also apart from 12V power supply.
@3Delite028 3 ай бұрын
I meant also connect USB power using phone charger with Printer cable to the board
@Mamiri1379 3 ай бұрын
Does the hotend have to be a special model? Or is it possible to use e3d v5 or v6 or should I make changes in it?
@3Delite028 3 ай бұрын
No special hotend required
@Mamiri1379 3 ай бұрын
And also another question: Since filaments are standard with a diameter of 1.75 mm, wouldn’t it be better to drill the nozzle with a 1.75 mm drill bit?” ❤
@3Delite028 3 ай бұрын
If it is available then definitely go for 1.75mm Since i didn't find it around me so i chose to go with 1.5mm since its was Bowden extruder
@TRX-x001 3 ай бұрын
Where i can buy heating blockand ceramic cartridge i can't find your type of heating block online ... Please send any link or name of market in Delhi i you now ...😢
@3Delite028 3 ай бұрын
There are plenty of online option Robi.in roboticsdna Novo3d These are the names of few websites you can search It is very cheap also
@3Delite028 3 ай бұрын
In Delhi specifically I don't know brother
@TRX-x001 3 ай бұрын
@@3Delite028 hmm ..any link for online
@TRX-x001 3 ай бұрын
@@3Delite028 one more thing could you please name the heating block which you used in video .. please
@Mamiri1379 3 ай бұрын
One of my problems is that I don’t have access to this type of engine, and it’s not available in my country. Could you please suggest a similar engine or tell me exactly what specifications the required engine should have?
@3Delite028 3 ай бұрын
Which country are you from ?? If there is services from china You can order same parts from AliExpress or bangood etc. Otherwise there is no special equipment used here Its just a DC motor with gear drive for pulling which can also be done manually if you want to just try first. Then there is heater, temperature controller with relay for heating element. Rest all can be easily sourced
@Mamiri1379 3 ай бұрын
@@3Delite028Unfortunately, I do not have access to this engine
@Mamiri1379 3 ай бұрын
asrerobotic.com/product/zga37fh-%D9%85%D9%88%D8%AA%D9%88%D8%B1-%DA%AF%DB%8C%D8%B1%D8%A8%DA%A9%D8%B3%DB%8C-12%D9%88%D9%84%D8%AA-10%D8%AF%D9%88%D8%B1/?PPC&Torob
@Mamiri1379 3 ай бұрын
But this model exists
@Mamiri1379 3 ай бұрын
“Hello, thank you very much for the detailed explanations. I have a few questions about this topic. How can I contact you? WhatsApp, email,❤ etc.?”❤
@3Delite028 3 ай бұрын
Insta id is given in the description Please feel free to connect
@shortsofenglish 3 ай бұрын
Should I take ssr 10DD instead of 25DD Or power supply without fan
@3Delite028 3 ай бұрын
Yes but make sure your power supply doesn't exceed 10amps
@Akashpoddarvlogs 3 ай бұрын
Ssr -10 dd works?
@3Delite028 3 ай бұрын
Yes but make sure power supply current does not exceed 10amps
@ayessapekit1698 4 ай бұрын
how did you set up the heat controller?
@3Delite028 3 ай бұрын
This is ready made module of REXC100. If you have spare nozzle set and board you can use that also. Like controlling nozzle temperature 🌡️
@ibrahimahmed529 4 ай бұрын
Can I use SSR-40 DA
@AudioBookGenerationArab 4 ай бұрын
Great tutorial, please I need all the prototype design files for the used plastic parts
@3Delite028 4 ай бұрын
Please check description I have given all files on thingivers
@shirzadshojai4535 4 ай бұрын
👏👏👏👏👏👏
@mwangolatrue 4 ай бұрын
Looks good
@Kishan010 5 ай бұрын
What is the cost of all 3d printed parts of 3d printer
@3Delite028 5 ай бұрын
Haven't calculated cost yet for this one..
@Kishan010 5 ай бұрын
What is the cost of all 3d printed parts
@3Delite028 5 ай бұрын
Around ₹2k
@skrilla.scratch 5 ай бұрын
Lovely!!!
@azizcanbilgic 5 ай бұрын
Hi! I have the same board as your, for marlin, did you change any other thing for the config file? If so, could you please share me the config.h and config_adv.h please? Thanks. 😄
@3Delite028 5 ай бұрын
Yes I have shared in the g drive link. Pre configured marlin
@azizcanbilgic 5 ай бұрын
Oh I, didn't saw it! Thank you a lot sir! Have a great day and keep going! 😁@@3Delite028
@carlroy1865 6 ай бұрын
error Requires ~3226 bytes wtf am i doing wrong?
@3Delite028 5 ай бұрын
Don't know the solution 😕 Really sorry for that. Just sharing my recent experience. I used original Arduino mega 2560 for my recent printer. My LCD display would turn off as soon as i connect to power supply. I searched a lot but couldn't solve the problem. Then i replaced original Arduino with cheap clone that i used earlier then everything worked well.
@3Delite028 5 ай бұрын
Please try to search the error code on Google, you may find similar problems and solutions. Since i am not from electronics or computer background i really don't know the possible solution.
@Ratchet4483 6 ай бұрын
I'm waiting for someone to make 3D printed Gundam/mecha using PET bottle filament.
@jim-6611 7 ай бұрын
this gc motor is not available in my country :/ Do you know any alternative for it that would fit?
@3Delite028 6 ай бұрын
You can use the set up which uses stepper motors. But it involves coding and other electronics arrangement. You can try using 2 smaller geared motor. The one which comes with plastic gears or servos with 360 degree rotation.
@3Delite028 6 ай бұрын
facebook.com/woodmood.tsp/videos/408442018268886/?mibextid=rS40aB7S9Ucbxw6v
@jasongooden917 7 ай бұрын
sounds like music from Ninja Gaiden
@vikis9 7 ай бұрын
I am not Pro to 3D Printing, i am new, but you can't compare Orca and Cura original profiles. As far as i know, Cura have better settings for original printer profiles, but in Orca, speed, travel settings, maybe more than that is not the same, they are slower. If you wan't OrcaSlicer to be close to Cura speed, you need to make adjustments. Becouse i am new in all that, i am searching and trying to learn more, but i know that Orca is slower becouse speed settings are not the same originaly and not only speed settings. I have tried premaid profiles with Orca and speed is slow. So my thougts is that we need to learn how to fine Tune Orca for our printers. Im searching for info and other things in every spare time i have. day i learn new things for 3d Printing.
@3Delite028 7 ай бұрын
Absolutely right bro. I just shared the thoughts about default profiles of both slicers Since i tried Orca without changing the default settings i got poor result, after changing z hop/ offset value to zero then got better results. I also haven't both software exhaustively. I just shared what problem i faced while using orca slicer for the first time.
@aryanpanchal8970 7 ай бұрын
what is the build volume of this 3d printer?
@3Delite028 7 ай бұрын
The build volume is approximately 250x300x300 Since i used smaller bed and smaller lead screw for z axis. I used 500 mm length Aluminum extrusion so build volume can be easily made to 350 in x axis Greater then 250 in y axis And upto 350-400 in z axis also. After Some changes in bed design
@aryanpanchal8970 7 ай бұрын
@@3Delite028 what dimensions you have used for aluminium extrusion in all axis? And i want to add heatbed also
@hazemhk8984 7 ай бұрын
hey man , i have a proplem Error compiling for board Arduino/Genuino Mega or Mega 2560. can you help me
@3Delite028 7 ай бұрын
Yes bro , what error code is it showing?
@hazemhk8984 7 ай бұрын
@@3Delite028 sorry for being late Arduino: 1.6.9 (Windows 7), Board: "Arduino/Genuino Mega or Mega 2560, ATmega2560 (Mega 2560)" In file included from sketch\src\gcode\lcd\M256.cpp:22:0: c:\users\hp\appdata\local\temp\build4d8a593d01e41d1e9db2b7443847d040.tmp\sketch\src\inc\marlinconfig.h:53:32: fatal error: ../core/language.h: No such file or directory compilation terminated. exit status 1 Error compiling for board Arduino/Genuino Mega or Mega 2560. This report would have more information with "Show verbose output during compilation" option enabled in File -> Preferences.
@hazemhk8984 7 ай бұрын
exit status 1 Error compiling for board Arduino/Genuino Mega or Mega 2560.
@dolphlungren59 7 ай бұрын
Hey man, that was an excellent video you made, and one of the most useful ones that I've seen on the subject. You even included multiple PCB wiring diagrams. It was very helpful. Thanks.
@shubhampawar4760 7 ай бұрын
How much it cost?
@3Delite028 7 ай бұрын
6-7k approx. I had most of the components available so it was very less for me.
@prashantchanchal1551 4 ай бұрын
@@3Delite028How to connect with you?
@chandanelectroniclab 7 ай бұрын
Wow nice 👍
@3Delite028 7 ай бұрын
Thanks 😊
@DaniMalik-uf6hd 7 ай бұрын
And can you tell me about setting of temperature for 0.4mm nozzle if we drill 1.5 mm more on nozzel end then what is range of temprature we set kimdly tell
@3Delite028 7 ай бұрын
This are the settings for 3d printing I used prusa slicer with bed temperature of 70 degree Celsius and nozzle temperature 250 degrees Celsius. For bed adhesion i used normal glue stick evenly applied to bed. This setting for filament extrusion from 1.5 mm diameter hole on modified nozzle Initial temperature of 130 degree Celsius for feeding filament. And 200 degree for making filament
@davideserafini4022 7 ай бұрын
Do you ever encounter clogging with this filament?
@3Delite028 7 ай бұрын
Yup bro initially it happened due to less temperature of nozzle which was 240 degrees Celsius on my ender 3v2. But when i heated up nozzle temperature to 250 degrees Celsius it extruded like butter. I used prusa slicer with bed temperature of 70 degree Celsius and nozzle temperature 250 degrees Celsius. For bed adhesion i used normal glue stick evenly applied to bed. Hope this clarifies all your doubts.
@davideserafini4022 7 ай бұрын
@@3Delite028 thanks for the answer. also, how much flow rate do you set?
@3Delite028 7 ай бұрын
There is a setting called extrusion multiplier. I had stock extruder on my ender3 v2. Which didn't work for 1.5 mm extruded pet filament. I also tried 2mm hole on nozzle but it was getting struck in bowden tube. So i chose 1.5 mm diameter hole for nozzle. And used dual gear extruder with stock steps per mm And extrusion multiplier value = 2 For prusa slicer.
@3Delite028 7 ай бұрын
I upgraded my extruder to creality dual gear extruder without calibrating steps then directly changing flow rate to double value. This printed well for PET filament. Whenever you upgrade extruder firstly calibrate steps per mm for extruder for normal filament like PLA. Then for PET filament you just make test print with extrusion rate 1.4/1.5/2 times the normal since pet filament are hollow inside.
@davideserafini4022 7 ай бұрын
@@3Delite028 thanks very helpful
@DaniMalik-uf6hd 7 ай бұрын
Bro tell me one thing is 0.4mm dia of hot end nozzle is produce 1.75mm dia filament or not means how much dia of nozzle we used for 1.75mm filament dia produce
@3Delite028 7 ай бұрын
0.4 mm diameter nozzle was drilled with 1.5 mm drill on smaller diameter end and 3-4 mm diameter hole on the other side from where the plastic strip enters the nozzle
@DaniMalik-uf6hd 7 ай бұрын
And can you tell me about setting of temperature for 0.4mm nozzle if we drill 1.5 mm more on nozzel end then what is range of temprature we set kimdly tell
@DaniMalik-uf6hd 7 ай бұрын
And tell me about black and red wire that connwct with pwm controller with which you connect these two wires or motor terminal yes or not
@3Delite028 7 ай бұрын
www.google.com/search?q=pwm+dc+motor+speed+controller+circuit+diagram&oq=pwm+dc+spe&gs_lcrp=EgZjaHJvbWUqCAgDEAAYFhgeMgYIABBFGDkyBwgBEAAYgAQyCAgCEAAYFhgeMggIAxAAGBYYHjIICAQQABgWGB4yCAgFEAAYFhgeMggIBhAAGBYYHjIICAcQABgWGB4yCAgIEAAYFhgeMggICRAAGBYYHjIICAoQABgWGB4yCAgLEAAYFhgeMggIDBAAGBYYHjIICA0QABgWGB4yCAgOEAAYFhge0gEINTM5OWoxajeoAhSwAgE&client=ms-android-oppo-rev1&sourceid=chrome-mobile&ie=UTF-8#imgrc=K_GCITuBH2uMOM&imgdii=672bTMksMRaJyM Check out image link. If you still have confusion, please tell