Sir, explanation is good and perfect, how can i learn from you how to repair the vfd drives

I have an altivar 4Kw and as i connect it to the power supplyakes a hissing sound and stops again hissing sound and stops,have you seen it again?

sorry, but if we have not EV-AD2, we can not test this smoke detector with only electricity supply?

Informative

Sir please give your contact

Hello, i have board am working on and i could use your help. With some small things Please share your mail so we can talk, thank you

Sir

Hii

If there is fault of short circuit without connection of Motor what we should do

Can any one do me a favour and answer me Is there any way to use <UG 8 dial> as a governor of ship engine which is need different speed?

i have a query regarding alborg boiler..actually it is because of the touch screen display showing "comm. error" offline 1..then, i switch to emergency mode, but it doesnt work, i followed the procedure, oil pressure ok, it is igniting but it is not firing at all. there is no indication in the flame scanner that it' s firing..hope you will give me a suggestion regarding this..thank you

there are two flame sensor right?manual and automatic..so what to do is just put the manual sensor to the auto sensor position?vice versa..thanks.😊

Still leaking

Hai plz send your number

Hi.. we are facing an issue with TMC compressor. loading unloading takes placeevery three to four seconds..

hi can you pls tell me how many types of alarms on igs as per solas

Hello sir.....have you ever had a Framo pump shear a shaft once but then a second time a few months later. The pump seems to be OK

Please give contact number

Your phone number not working bro

Burgan .... I think

How can replace programed vfd

hello! i have a problem with donkey boiler Mitsubishi seems like on yor video. My boiler staring and in step 4 (ignition rate set order) of seaquence stuck ((( can you explain which order will be set to become step 5 ?

Frenic 5000g11 power supply fault vfd not power on

thank you for the video. How do you reset the compensation pointer en needle valve after an oil change?

on the same thing sir, can we do this while the main engine is running?i think it will stop the main engine??

Vacon ka lift vfd drive ka out put on off ho raha ha Kia reason ho ga please

nice info thanks for sharing

What's the price of magnetic reed switch

Thanks , very informative.

Sir how to slove err-24 code

A nice and clear explanation of the flex system

Nice job

Drive not on

Bhai Mera output voltage drop ho raha hai kya problem ho sakti hai

sir, what is the reason of placing positive wire of multimeter with negative point of VFD, and then you change by putting negative wire of multimeter with positive point of vfd,,,,pls explain...any reason????

I have trouble with this equipment. After blackout can't ON. Power supply 220VAC is ok. Inside power supply LED is on. Output 24VDC is ok. But inside small display not indicating. The remote controller shows errors for temperature and viscosity.

Sir how about the valve is not opening in automatic

Stupid video..

Input is ok but out put low byepass is not working give solution

10 KVA LANA HAi. Plaese Cotect. Kere

36kw. Stabilizer how much sir

Super sir

From where I can order this servo stabilizer? Please provide me link, website....

Mujhe bhi repair karwana hai please phone no send kare

For two 1.5 ton ACs, 5 fans, 15 lights, 1 water pump (to fill overhead tank), 1 microwave, 1 refrigerator, 3 led Tvs and 2 desktops. Will 10kva capacity of mainline servo Stabilizer be enough??

Thank for sharing!

Remove the fees for all the videos

What the purpose of servo oil motor sir?

very valuable explenation sir, keep up the good work

Hi sir, i would like to know if the drive keyboard is included with the variable frequency drive of Frenic Lifts. I have the same make installed in my home elevator. The technician is asking for extra 15k Rs to replace the board as it was missing.