Күн бұрын
Пікірлер
@johnnorton7636 9 күн бұрын
most windows the cam opens towards the handle
@VLVIC 16 күн бұрын
Надо последовательность операций поменять.
@JFmontadordemoveis84 22 күн бұрын
ola, gostaria se saber onde compro essa ferramenta?
@SouberTools 21 күн бұрын
What country are you from ?
@SouberTools 21 күн бұрын
Hafele Brasil stocks this in Piraquara
@MdSharifulislaml-d9u Ай бұрын
দাম কত ছোট করার মেশিনটার দাম কত বাংলাদেশী প্রাইস
@mochmadsupriyadi 2 ай бұрын
Beli dimana alatnya
@catr900 3 ай бұрын
Vilken maximal bred på karm klarar den av? (vid fräs av slutbleck)
@SouberTools 3 ай бұрын
The clamps will open to 100mm maximum. Above this dimension you need longer clamp screws. (Part No. DBB/LCS). Then, it can open to 200mm maximum. However, the full "left to right" movement is reduced above 140mm.
@horstzielke9535 4 ай бұрын
Musik in Erklärvideos ist unnötig und es nervt.
@SouberTools 4 ай бұрын
You can always use the mute or volume control if you don't like. This is your choice.
@bensons999 4 ай бұрын
nice
@Door-tool 5 ай бұрын
😮
@YsufxonYkubbaev 10 ай бұрын
Салом нечпул экан
@danthechippie4439 10 ай бұрын
Hi, great looking tool, where is it available in Ireland?
@SouberTools 10 ай бұрын
McQuillans of Dublin distribute it in Ireland.
@danthechippie4439 10 ай бұрын
Thank you for the quick response, I'll check it out. I noticed that you also provide for off ctr locks in rebate doors. Is that a different mortiseor or can I purchase an adaptor for your standard one? Thank you
@SouberTools 10 ай бұрын
@@danthechippie4439 Go to www..morticer.com for details. Watch the videos and take a look at the sales leaflet. You can order the separate Housing Kit to make it work "offset" from the supplier.
@krcright9746 Жыл бұрын
I was impressed the first few times I used this de-glazer. then the curved end blade started to straighten out slightly when using on some stubborn beads,, making it now difficult to use, must be manufactured from low carbon spring steel material for it not to remain in shape
@SouberTools Жыл бұрын
If you return it to Souber Tools and it is found to be faulty a replacement will be supplied.
@krcright9746 Жыл бұрын
@@SouberTools More trouble than it’s worth sending it back. I’m sure it will come in handy for something else
@SouberTools Жыл бұрын
If it's faulty, let's see the photos : [email protected]
@SouberTools 11 ай бұрын
It's been over a week and still no photos. @@krcright9746
@brighton_locksmith Жыл бұрын
Simple but effective 👌🏼
@BobHolster-om8rf Жыл бұрын
NICE BUT HOW DO YOU KEEP THE LONG DRILL BIT FROM GOING ASTRAY? DRILL BITS HAVE A MIND OF THEUR OWN EVEN IN A JIG.
@SouberTools Жыл бұрын
This Drill bit does not have a conventional tip. It uses the same design as the people who drill the old wooden lampstands. When it hits a knot in the wood, the noise changes pitch but continues to cut straight. It cuts in 3 places at once using a lip and spur design. The important thing is if you start straight it continues straight. Furthermore, keeping the jig aligned is important and correct stance is advised in the Long Drill instructions. This means no deviation and no strain on the Jig or housing. If you follow our instructions you should "pop-out" within 10mm of centre. I usually expect most achieve it within 6mm.
@BobHolster-om8rf Жыл бұрын
THANKS.@@SouberTools
@ssksalesandservices Жыл бұрын
product link plz
@SouberTools Жыл бұрын
www.morticer.com
@camronbay1 Жыл бұрын
I’ve used the ones at Home Depot they work pretty good I want to get some like this.
@citylockapolytechnikeyllcc7936 Жыл бұрын
No Video on your Mercedes ignition cap cutting kits ?
@SouberTools Жыл бұрын
They were discontinued years ago.
@iceman27406 Жыл бұрын
where can we pick this up in the US only place i saw was a German website
@SouberTools Жыл бұрын
MBA USA In Kentucky are stocking the Master Kits only at present. That's 8 burrs in a set. 5 Magi Burrs plus 2 plain burr and a safe end burr. I expect them to stock the individual Burrs some time soon.
@TheMilkman710 Жыл бұрын
That's the worst rake I've ever seen.
@SouberTools Жыл бұрын
We'll wait for your faster video to get uploaded !!😄
@TheMilkman710 Жыл бұрын
@SouberTools lol. I was joking. That's obviously not a rake pick. The tool is really cool though. Does it cut through tile?
@SouberTools Жыл бұрын
@@TheMilkman710 I guess you mean Porcelain Tiles. I would say no there. It's designed for locks and the material in them is Brass.
@ronblack7870 Жыл бұрын
the lock picking lawyer is asking why did it take so long?
@SouberTools Жыл бұрын
The quickest we've done it is about 40 seconds. But, it comes down to how quickly the pins jump out. Unfortunately, Medeco is no longer sold in the UK so we used some old stock I found stashed away in store here........So, we'll now have to wait for you to post your videos instead
@camronbay1 Жыл бұрын
@@SouberToolsThey have no videos to show amateurs everybody thinks the lock picking lawyer is the best for some reason.
@jobandknock427 Жыл бұрын
Bought my DBB about 6 years ago to replace the Trend router jigs, and I've been using the smaller diameter plunging cutters to do tubular latches for a while. They work well. Last week I got hold of the 29 and 32mm plunging cutters so that I could install a number of Perko (Correction: they are Astras, see below) tubular closers - the large 4000 series ones with the 280mm long body. Fire rated ones need a 31/32mm diameter hole, non-fire rated a 29mm hole. I've now installed six Astra 4000s into brand new solid oak doors, with varying thicknesses between 42mm and 64mm, as well as redrilling one door to 32mm where a colleague had inadvertently drilled the door at 29mm and couldn't figure out how to safely redrill to 32mm. This has always been a twitchy sort of job to do because you only have 6 to 7mm of timber between the hole and the face of the door, so even a couple of degrees out and you risk drilling out the side of the door - not a good idea with £2k plus doors! On chipboard core doors and softwood doors I find I can use a heavy cordless drill (Makita DHP481/DHP484) without problems - solid oak doors are somewhat harder to do and I'm happier with a corded drill on the 29 and 32mm holes Well done Souber for a great piece of kit!
@SouberTools Жыл бұрын
Glad to have helped you in your problem. However, the closers you mentioned were not Perko's but would have been the Astra Closer. Samuel Heath would have something to say about that as they make the Perko closer.
@jobandknock427 Жыл бұрын
@@SouberTools Yes, indeed. We tend to call all these things by the generic name, a bit like Hoovers.
@MoroccanAnwar Жыл бұрын
1st
@sherzodalimatov7256 Жыл бұрын
Самый лучший шаблон DOOR PROFI
@Simylchuk 2 жыл бұрын
У них что, нет угловой стамески ? 🤣🤣🤣
@SouberTools 2 жыл бұрын
No !!
@richardhorsham7395 2 жыл бұрын
I have recently purchased one of these jigs and I’m really impressed with it , easy to set up and use .
@curtisalleyne3710 2 жыл бұрын
Paul one of the best locksmith inventors in the industry
@phipear 2 жыл бұрын
I’m curious why Paul doesn’t recommend cordless? I realize this was 7 years ago but what is the limit of cordless vs corded?
@SouberTools 2 жыл бұрын
Hi Phil Agreed, that Cordless drills have improved. The requirement is a drill with 2500-3000rpm. Only a few Cordless Drills can do this. So, if you have a cordless which can do those speeds that might be acceptable. But, it must have a 13mm Chuck and not be too heavy. Heavy Drills can cause operating difficulties.
@rajraj3954 2 жыл бұрын
Contact number
@leliasse5751 2 жыл бұрын
J'aurais bien bien aimer connaître le noms de l'appareil que vous avez utilisés. J'ai voulu me servir d'une affleureuse pour faire ce genre de travaux mais pas suffisament profond avec les fraises.
@SouberTools 2 жыл бұрын
Souber Tools DBB Mortice Jig
@leliasse5751 2 жыл бұрын
@@SouberTools Super merci.
@elvatoloco5460 2 жыл бұрын
How open Jamb Door?
@SouberTools 2 жыл бұрын
You would have to use an Offset Housing kit. That would work on Frames up to 95mm wide. Over 95mm width you'd need longer clamp screws. But it's all quite possible.
@nelsonpalma6358 2 жыл бұрын
Donde la en centro y cuanto vale soy de chile
@РусланПух-ш3т 2 жыл бұрын
Вроде выбрано было не плохо, но потом накосипорил жесть!! Хотя б в видео не выставляли!
@xxyxnxwxaxx9724 3 жыл бұрын
Cutting the face plate part made me wince a bit, I could imagine it chewing up the timber. That kind of put me off. Imagine it messing a expensive oak door up. Cut the inside for the mortice lock I would like one if it cuts the time down.
@SouberTools 3 жыл бұрын
120,000 sold worldwide. That answers most questions.
@xxyxnxwxaxx9724 2 жыл бұрын
@@SouberTools I'm sorry if I touched a nerve, but it wasn't intended as a slagging off reply. I was just saying stating the sound from the cutting sounded rough. And yes I agree. That's a fair amount sold. But a 120.000 is a drop in the ocean to how many tradesmen there is out there world wide. Just saying.
@SouberTools 2 жыл бұрын
@@xxyxnxwxaxx9724 There are techniques for doing perfect faceplates. There are also ways to mess it up. I won't focus on the various do's and don'ts as I will start to get into a lesson on training and that will take hours.
@dagobertogarciapinturas7482 3 жыл бұрын
Dónde lo puedo comprar la máquina es fabulosa
@SouberTools 3 жыл бұрын
En que pais estas ?
@MrDINODINO74 3 жыл бұрын
... you should make the wider bit first.
@lohardinesh7387 3 жыл бұрын
Kitne pese ki hai sir
@michaelintile7836 3 жыл бұрын
Get a drill with a slightly higher speed Paul - it will make it a bit little easier..................(-;
@purcylouis127 3 жыл бұрын
Très pratique super
@nandankumar1340 3 жыл бұрын
Stand name plece
@SouberTools 3 жыл бұрын
Is this a question or a statement ?
@yousafkhan291 3 жыл бұрын
What's the price?
@SouberTools 3 жыл бұрын
You need to go to the website www.morticer.com Then, look at the product and then look at where to buy. It depends what country you are in.
@yousafkhan291 3 жыл бұрын
What's the price?
@SouberTools 3 жыл бұрын
Check www.morticer.com and ask a distributor in your country.
@thallapakanataraja3654 3 жыл бұрын
Call me sar please my phone number washap number 7989023660. Cast
@fireblaster9961 3 жыл бұрын
Thanks for sharing, I don’t know what I’d do with out this tool and makes me so much money
@danielstorton5696 3 жыл бұрын
This tool is awesome
@AlexisRodriguez-xq1zn 3 жыл бұрын
Mortise bore is the most important part any videos on that
@SouberTools 3 жыл бұрын
For more details go to www.morticer.com
@sunilvadher4435 3 жыл бұрын
Price
@SouberTools 3 жыл бұрын
Country ?
@shantelfullerton9865 3 жыл бұрын
Good and very accurate designs are on the Stodoys plans website.
@mohameddafir6560 4 жыл бұрын
Svp le prix de cette machine Je suis au Maroc Combien le prix avec la livraison
@menjaghatardetta1234 4 жыл бұрын
SLUTA FÅ DET ATT SE SÅ LÄTT UT