P Flinner

Пікірлер

@stevefrake8922 Күн бұрын

Carbon footprint???? 😅😅

@diaryofawanderingboot 20 күн бұрын

Slightly overboard with the wires. But hey, one can never be too careful

@jaypea3869 3 ай бұрын

Still on my racer r pro and second skwal 2. So, as an apparent psychopath, I'll upvote. :)

@DanielCastro-md1ow 3 ай бұрын

hi man thanks for the video was great. how did you remove the plastic covers from the motorcycle? I have a Tiger 900 GT Pro and will be running a cable to power a GPS device. Any suggetions for it would be much appreciated.

@PatrickFlinner 3 ай бұрын

Take off the seat, you will see 2 bolts each side on the plastic fairing, remove, then pull each one backwards. Gently. Else use a wire to route your cable under the tank, follow the frame tubes.

@DanielCastro-md1ow 3 ай бұрын

@@PatrickFlinner thansk Patrick for your help will get this done this weekend!

@jaspergats8385 4 ай бұрын

Please would this stop oil leaking from the weep hole?

@PatrickFlinner 4 ай бұрын

@@jaspergats8385 yes. Oil leaks from that because the seal is about to go

@qamihai2585 4 ай бұрын

Hello Doc. I have a quick question, I saw where you put the shim, and I saw where you put the washer. But where is the rubber o-ring in all of this? Is it behind the impeller or in front of it?

@PatrickFlinner 4 ай бұрын

Can't remember. Google KLR exploded parts view, it should show its location.

@costaboskoff4116 4 ай бұрын

Can not hear what you are saying

@AleksandarStojiljkovic 6 ай бұрын

Shorter velocity - higher torque and rpm. Higher velocity -low down torque and dead top end

@StanTheMan-us3tp 7 ай бұрын

Hello, mate Canadian dude here, I see that you’re still answering questions here I think it’s awesome, What was the indication that it was the seal in the first place? My coolant was empty when I inspected it after it had been stored. Just from the remnants of the fluid it appears around the water pump is where it was coming from.

@PatrickFlinner 7 ай бұрын

@@StanTheMan-us3tp two clear signs: either oil or coolant weeping from the little hole at the bottom of the pump enclosure. It can also occur that coolant mixes with oil in the sump. If you got a baseplate you will see liquid after a short ride once the engine has warmed up

@1990AngeloS 7 ай бұрын

What you pay for those stacks bud ?

@PatrickFlinner 7 ай бұрын

@@1990AngeloS came in at about R800 a pair

@1990AngeloS 7 ай бұрын

@PatrickFlinner cheers man You in cpt ?

@PatrickFlinner 7 ай бұрын

@@1990AngeloS naah. Engine room: Johannesburg. Keeping the upper decks running on the titanic

@1990AngeloS 7 ай бұрын

@@PatrickFlinner ha ha😂 ride safe bud

@1990AngeloS 7 ай бұрын

Fuck sakes i just spent R1900 on a bmc 😢

@Zwiepmoto 7 ай бұрын

How many kilometers did you rode before re-greasing the headstock bearing?

@PatrickFlinner 7 ай бұрын

Well being the last owner kind of forced it. Grease has a limited lifetime. 5 years is pushing it. Also a great way to tell if it has wheelie d hard

@6sensory 8 ай бұрын

Very humorous

@mattiadreossi754 8 ай бұрын

Hello!! Good video, can i ask where did you get the extra foam seat and the tailight?

@PatrickFlinner 8 ай бұрын

Foam seat: take it to an upholsterer, they can re-stuff it. Tailight: Any LED bulb will do.

@mattiadreossi754 8 ай бұрын

@@PatrickFlinner Thanks!

@danielboekweg2919 10 ай бұрын

What kind of lube did you use to get the seal on? Would just petroleum jelly work or does it need to be engine rated?