Пікірлер
@Dyggyty 2 сағат бұрын
@Mangorille So I've got this issue due-to the flight in about 500 meters away from me. Before that drone was able to get 2,5 km with link speed down to 5 mb/s (because of obstacles) and get back to 50 mb/s. And I've got freeze at 25 mbit :). RTH works fine (I tested before the flight. So I was ready for that) and I was able to rebot unit in the flight (I do have power managment for VTX on board). Unit was able to reconnect. But was started in low power mode (as before arming). But it's OK to get home
@peterpeterson7993 6 сағат бұрын
Thank bud for the video. What RC you have used to fly googles 3 with o3 units. Thanks
@Mangorille 5 сағат бұрын
I use a Tango 2 Pro with an internal ELRS module. kzbin.info/www/bejne/iKDHlpqQn86Efc0
@peterpeterson7993 4 сағат бұрын
@@Mangorille great to know. Thanks. I was under impression you can only use dji RC3 with Google 3
@Mangorille 4 сағат бұрын
You are correct if you plan to use the DJI remotes. If you use a crossfire or ELRS, these are independent control links that have nothing to do with the DJI portion of your quad. You install a separate receiver for these remote controls.
@peterpeterson7993 3 сағат бұрын
@@Mangorille thanks bro. I'm planing to buy 5 inch iFlight nozgul quad with O3. Just buy ELRS version and get matching controller or bay all dij and control it through RC3?
@Mangorille 2 сағат бұрын
I’d recommend getting the ELRS version and then whatever is your favorite ELRS capable transmitter (the Radiomaster Boxer is popular). Problem with the DJI RC3 remote is that they don’t use full size gimbals so you don’t have the same resolution, they connect to the quad through the goggles so if you lose video you also lose remote control, and they go end of life very quickly (look at the RC2 that was released 2 years ago, already end of life with the release of the Goggles 3)
@OstapDemchyna 2 күн бұрын
It's strange because when I do set sbus_baud_fast from CLI it shows me an error: INVALID NAME: sbus_baud_fast## does anyone had this issue?
@Mangorille Күн бұрын
When you flashed your flight controller, did you include the SBUS protocol as one of the radio protocols? I'm 95% sure you probably didn't. :)
@OstapDemchyna Күн бұрын
@@Mangorille Hey thanks for your answer. The issue for me was that I have betafpvf405 on pawo20pro controller and I ask for support to betafpw and they suggest me to flash 4.5.0 framevare because stock has an issue with sbus.
@siddhantpatel7099 2 күн бұрын
A very unrelated question. I am from India and the G3 are quite expensive here. So i have asked one of my cousins who is coming to India next week from US to get me one. Do you think i should, maybe wait or can i just ask him to get it and wait for the firmware update? What if there is a hardware issue with the G3?
@Mangorille Күн бұрын
Until DJI announces a fix, no one knows what the issue is. The common thinking right now is that the issue is in the firmware.
@moehnget 2 күн бұрын
How can we use Goggle 3 with analog VTX ?
@Mangorille 2 күн бұрын
No, there's also no AV input and it only works with the O3 air unit right now.
@moehnget 2 күн бұрын
@@Mangorillethanks
@ukmonk 2 күн бұрын
Has this issue been addressed yet please?
@Mangorille 2 күн бұрын
Nothing yet from DJI. I still haven’t had this happen to date.
@ukmonk 2 күн бұрын
@@Mangorille Thank you for replying. I just got a brand new iFlight Nazgul (O3 unit) but only taken it out once (Using it with RC3 and googles 3) as I saw people telling their horror stories of it falling from the sky. Scared to go out and fly it now. Hopefully they will fix it soon…..
@Mangorille Күн бұрын
@@ukmonk Welcome. Hopefully soon... Been nearly 2 months of waiting at this point...
@ukmonk Күн бұрын
@@Mangorille thanks for replying 😊
@picturelessboss6113 2 күн бұрын
Hi there, thanks for the info. Watching your flights and noticed you turned left quite alot, don't know if you noticed but you need to correct that. Used to do do the same thing and ended up turning one side better than the other and had to work to improve on turning in the other direction.
@Mangorille 2 күн бұрын
Hello. Yes I’m aware. A bad habit developed over the years that I need to work on.
@vietlongle4867 3 күн бұрын
help me for the controller driver plsss!
@Mangorille 2 күн бұрын
What’s the issue?
@gimbalair 4 күн бұрын
Just bought a nazgul with vista, updated vista, bound everything but the range is dreadful, video feed is dropping out behind a low bush 80yds away. Now i have confused myself, do I use the old naco.txt file on the sd card in the goggles2 or do I use the ham file on the goggles 2. More over do I need to plug in the vista and drop the file directly onto the vista unit? Help appreciated.
@Mangorille 3 күн бұрын
You just need to use the ham file on your goggles 2. The naco text file is only if you have the Goggles v2 or v1.
@gimbalair 4 күн бұрын
Just bought a nazgul with vista, updated vista, bound everything but the range is dreadful, video feed is dropping out behind a low bush 80yds away. Now i have confused myself, do I use the old naco.txt file on the sd card in the goggles2 or do I use the ham file on the goggles 2. More over do I need to plug in the vista and drop the file directly onto the vista unit? Help appreciated.
@gimbalair 3 күн бұрын
That’s a I understand it too. Do I need to delete any file off the vista too. I have use the ham file, i see 40hz and 3 channels but the video feed is really poor even a short distance when it goes behind a bush
@sadochist 5 күн бұрын
In my case this shituation happend 2 times per maybe 100 packs. One when i was like 500m away from drone in a clear field, second shituation when i was maybe 30 m away with some bushes crossed path. No trust in system at all now
@Mangorille 3 күн бұрын
I still haven't had the issue happen yet but these reports make me not trust the system and definitely not fly anywhere that I can't walk over and recover the quad. Still nothing from DJI...
@BlesinskiTravel 6 күн бұрын
What is with Mavic 3 pro or cine?
@Mangorille 5 күн бұрын
No, was on a DIY drone. Video here: Could This Be My NEW SUB 250 Gram 3" HD Freestyle Frame? | Quadmula Siren F3 Split & DJI O3 Air Unit kzbin.info/www/bejne/f3yroIOors2peck
@gilangrambu7203 7 күн бұрын
Hello bro, I'm O3 user with Goggles V2, can this update record OSD via the goggles like G2 & Integra ? 🤔 Thx
@Mangorille 7 күн бұрын
Unfortunately no, the WTFOS modification only works with the v1/v2 + old generation air units. To record the osd with the o3 air unit you need the goggles integra, goggles 2, or goggles 3.
@Donalduck330 8 күн бұрын
Do you Think the walksnail moonlight will fit?
@Mangorille 8 күн бұрын
I haven’t tried but I think it may. The moonlight uses the same 25x25 mounting of the o3 but it is about 2mm bigger so that’s the concerning part. Try emailing Quadmula to confirm, their support is quite good.
@KingHaggis 9 күн бұрын
I can only use the Integra goggles without a faceplate. It's very uncomfortable but it's the only way I can see the entire screen with blurry corners. I guess I need a really thin faceplate. Would this one be good for me? It looks a bit thick.
@Mangorille 9 күн бұрын
It’s rare to have a blurry edge problem on the Integra. DJI reduced the FOV to resolve that problem. I don’t think this faceplate will make a huge difference for you especially since the Integra already use a different faceplate than the Goggles 2.
@AnthonyVella 10 күн бұрын
I recently wrecked my paramotor and broke my body pretty bad. Since I’m physically unable to launch (at the moment), I’ve gone down the FPV path and I’m seriously loving it! I found this video to be fantastic and now I’m strongly considering ordering this frame/parts. Thanks for the inspiration!
@AnthonyVella 10 күн бұрын
Do you still recommend this quad for a 2.5”? Is there another one that you’d recommend?
@Mangorille 9 күн бұрын
Sorry to hear about your accident. FPV is a great hobby! What kind of flying are you thinking of doing? More slow cinematic flight or some freestyle as well?
@FateShape 11 күн бұрын
I didn't know dji generation gate their hardware. Was hoping to use them with the neo and upgrading to 5 or 6 pro when it releases. Good to know, I'll gonna hold back for now.
@Mangorille 11 күн бұрын
They historically have been, they seem to support just one generation back and then they end of life the product.
@SbangFPV 11 күн бұрын
A few drops of rainX on the lens works wonders.
@Mangorille 11 күн бұрын
Thanks buddy for the suggestion.
@RobertTheFriscoSchmid 11 күн бұрын
Loved your video, had me buy the frame and now I am stuck in ESC hell ... Right now when I load BlueJay, the motors don't all spin, actually only one does. However when I go back to BLHeli they all work. Same ESC/FC you have ... Any suggestions or ideas? THANKS
@Mangorille 11 күн бұрын
The motors don’t spin when you try to use the motor tab in betaflight either? Is it always the same one that start up while the rest don’t spin?
@RobertTheFriscoSchmid 11 күн бұрын
@@Mangorille running BLHeli all works fine, motors spin in Betaflight Config as expected. I upgrade to BlueJay 21 and only one motor spins. Then I thought I try BlueJay 19 and voila, all is good ... guess there is some incompatibility with 21. I posted something on their Discord and will update here if I find out why. THANKS for responding
@Mangorille 8 күн бұрын
@@RobertTheFriscoSchmid No problem. You may want to try increasing the start up power in the config, I had to do that on a tiny whoop when I upgraded the blujay firmware.
@RobertTheFriscoSchmid 8 күн бұрын
@@Mangorille great suggestion!
@thanatosor 12 күн бұрын
750 F here = 400 C ?
@Mangorille 11 күн бұрын
Correct. You can change your display from F to C as well.
@thanatosor 12 күн бұрын
So what are our choices nowadays? 😂 I used 936 like 5 years ago too. Just sold last year, still working well.
@Mangorille 11 күн бұрын
Hakko makes the new version of this, the FX-888DX that is nearly the same except buttons replaced with a wheel.
@МишаШелест-и2л 12 күн бұрын
How switch fcc mode on dji fpv controller?
@Mangorille 11 күн бұрын
Never heard of needing to switch the controller. Once you get your goggles and air unit into FCC mode the controller just follows.
@Rawk59 12 күн бұрын
Happymodel module bay attachement is out of stock everywhere. What would you pick today to do this mode ? Thanks
@Mangorille 11 күн бұрын
Use the TBS one, you’ll need to make space for the entire daughter board as I couldn’t find a way to eliminate it when I tried. The daughter board is fairly small so you should be able to make it fit with a bit of creativity.
@Kkp-s5c 12 күн бұрын
Ufffv
@fpvkevlar8101 13 күн бұрын
I lost connection, and my signal has been shit also. One, I can't even fly the signal is such shit right now with the 03 and Googles 3.
@Mangorille 11 күн бұрын
Worse than the signal you see in my video? If so, something else may be wrong with your setup.
@RonaldThomas-w4p 13 күн бұрын
Leannon Avenue
@jimskyboy2 14 күн бұрын
Too many errors on signal loss with the goggle 3 and the o3 air unit.
@Mangorille 13 күн бұрын
My experience so far is that it works okay, but definitely some kinks that hopefully DJI will resolve.
@chiprobertson3094 14 күн бұрын
The third flight video dropped out the battery was real low when it happened
@Mangorille 14 күн бұрын
Which flight you referring to? I run a 6s battery pack so the voltage is always above the minimum voltage of the o3 air unit.
@kaosvalentine 14 күн бұрын
out of curiosity, how is the unit affected by heat due to it not having the fan. i know the fan kicks in by default at 250mw? any over heating issues?
@Mangorille 14 күн бұрын
No issues. I did a 5 minute heat test during the install of the module at 500mw. kzbin.info/www/bejne/iKDHlpqQn86Efc0si=iEdW0ZXUJxkTNDgo&t=861
@tanoenaczycaitin 15 күн бұрын
I have the same setup as yours, but my expresselrs lua said "error1-firmware"
@Mangorille 15 күн бұрын
Are you using the LUA script that was generated by the version of ELRS you're on?
@tanoenaczycaitin 15 күн бұрын
@@Mangorille yes, from elrs configurator, i tried all, still no luck
@Mangorille 11 күн бұрын
@@tanoenaczycaitin are you able to update the firmware of the module through wifi?
@Rcschim 15 күн бұрын
Thanks - that's a bit reassuring now. Ordered the G3 now and some O3 units - and I dont wanna regret this ;) Yesterday I was out 5k and had 3-4mbits on a mountain with Gv2 and O3 - but looks like it was me setting a manual channel rather than using auto there. Next flight with Auto, 40mhz FCC mode... was fine - always good image. Really hope the G3 are as good as I think - else I will keep my Gv2 for longrange with their TrueRC patches. greets, Mario
@Mangorille 15 күн бұрын
Welcome. The Goggles 3 themselves are great compared with the Goggles 2 and Integra but the firmware right now isn't the greatest with the O3. Still a fair amount of stuttering, feels like it's still a beta firmware. I'm going to try a manual channel selection as well, see if that helps.
@samu.miller 16 күн бұрын
For all pilots with O3 problems - here is a very recent & important update from the User ,,Guy Aroshas`` in the official DJI Forum: ,,The source of the problem is only the Goggles 3, and not any other. It is not the new firmware for the O3, so there is no problem updating. To reproduce the problem, I connected the Goggles 3 to my drone, and armed it in my house without taking off. I then started to go away from the drone until I lose video. When coming back to the drone, video is not restored until disarming. The problem is that once the Goggles 3 loses video, it only searches for a disarmed drone (which is always transmitting on channel 8). So I can conclude that they only scan channel 8 after losing video. To prove that, I tried another test, where I armed the drone before powering up the goggles. After powering up the goggles, the same thing happens. The goggles don't find the armed drone. I can conclude that upon powering up the Goggles 3 they also scan only channel 8. I have tried the same tests, alternating between Auto and Manual channel selection. and also alternating Low Power Mode and Auto record, enabled and disabled. The same results apply. Losing video with the Goggles 3, even for a brief moment will result in the black screen of death, and it will not come back until you disarm, and get close enough to the drone. I then proceeded to do the same tests with my Goggles 2, and no matter what, they can connect to my drone, armed or disarmed, and will recover video when coming back to the drone after losing video. I can say with confidence that it is unsafe to fly with this combo of Goggles 3 + O3, until a fix is released. Even a small interference which will cut your video briefly will cause this problem. DJI PLEASE READ! I have explained in details what needs to be done. The Goggles 3 needs a fix to search all channels for bound drones. Please fix this ASAP! Please forward my instructions to reproduce the problem to your technical team.`` Thank you!
@Mangorille 15 күн бұрын
There seems to be 2 different problems, although the root cause may be the same. There's the issue you mention but then there's the other issue where the goggles 3 will disconnect randomly in situations where the signal strength is strong (e.g. 50 mbps.)
@fpvkevlar8101 13 күн бұрын
I've had disconnects, and I've crashed, and it would not connect again. Also, huge stutters randomly. One quad when I arm I lose video completely and it never reconnects it also seems to be worse between builds this is a weird issue. Shits been acting weird since day one running the 03 with the Googles 3.
@Hopelesswanderer81 16 күн бұрын
DJI will fix it soon. There on there 💩
@Mangorille 15 күн бұрын
Hopefully. Been over a month since the firmware released and the problems started.
@gump1119 16 күн бұрын
I think the low bitrate on takeoff is related to heat in the vtx and possibly the unit throttling back. I noticed just bench testing the unit that the bitrate drops and if I point a small fan at it, it goes back up. How is your o3 powered? It stutters hard when you throttle punched and flipped over the tree. Maybe battery sag or voltage instability? Do you have a cap?
@Mangorille 15 күн бұрын
These would be good things to try if the issue wasn't isolated to the goggles 3. I've been flying the same quad with the same setup on the goggles 2 since the O3 released and haven't had these stutters. O3 is powered straight from vbat.
@gump1119 15 күн бұрын
@@Mangorille Yeah I’m not disputing that it’s a problem with the new goggles. Just trying to narrow it down and maybe find a bandaid until dji fixes it.
@Mangorille 15 күн бұрын
@@gump1119 Understood, thanks for the suggestions.
@aghasardjanto4752 16 күн бұрын
Guys! On the new FW, I still got BAD STUTTER when doing HARD Flip ( pitch or rolls) which doesnt happen on my V2. Tried Everything and found out switchingFOCUS MODE to AUTO fix the stutter 🎉. Hope this helps .
@Mangorille 15 күн бұрын
Thanks for the suggestion, I'll give this a try. I have Focus Mode set to Off.
@RockFPV 17 күн бұрын
Admitting mistakes is usually not really part of Asian Cultures. I even had it dropping out on the desk after updating to the newest firmware and resetting the goggles 3. Only did one pack with my Pavo Pico, staying low to avoid any damage. It did not happen but that's the Problem, it does not happen on every Pack. Before I had it for the first time, I did around 6 Packs with different quads and besides frame drops eg. stuttering it did not lose video completely and I just thought "It's fine" - but it is not. I am currently not flying my O3 anymore until it's clear what happens and / or the issue is fixed. These kind of "Beta Tests" can be dangerous and expensive.
@Mangorille 17 күн бұрын
Ya, that's the problem, it happens intermittently and catches you off guard. I haven't had it happen yet over 30 packs but I know it's a possibility at any point.
@my.fpv.flights 17 күн бұрын
I also made an ultra light. But now I have a strange problem: during a steady flight everything is fine, but if I make sharp maneuvers - the video in the glasses slows down or even freezes for a second or two. Of course, this leads to a fall. The video that is recorded on the module is fine. The problem is with the video transmission. I think it is somehow connected with the removal of all the covers. I could assume that I made a mistake somewhere, but it is noticeable that TWO dji o3 behave this way, which I stripped naked. In this video, a comparison of the video from the glasses and from the module. For two different o3. I thought that perhaps the P1 cannot work without cooling, but I have seen many for whom it works perfectly. kzbin.info/www/bejne/g5LddGSYra5mhaMsi=HFxE9DnrtbNLpOMe Are there any ideas?
@Mangorille 17 күн бұрын
You seem to have really weak signal strength given how close you are to yourself. The o3 signal degrades a bit when you get off axis so that's fine but even when you are not doing sharp maneuvers, you're mbps is all over the place. Are you sure that the antennas are connected fully? What goggles you using?
@Mangorille 17 күн бұрын
Also, note that the o3 has a voltage requirement of 7.4-26.4 V. That's why you probably had the first disconnect, you went down to 7.3v.
@my.fpv.flights 17 күн бұрын
@@Mangorille in that case it should be visible in stock version….
@Mangorille 17 күн бұрын
@@my.fpv.flights Did you make any other changes? I don't see how removing the case would cause this to happen unless a connector was damaged.
@my.fpv.flights 16 күн бұрын
@@Mangorille no, I am going to try to use top plate from another o3. let's see
@wes4274 17 күн бұрын
I HAVE BEEN FLYING 03 WITH GOGGLES 3 WITHOUT ISSUE . Could it be a power supply issue to air unit ?
@Mangorille 17 күн бұрын
No weird stuttering either? I haven’t gotten the disconnect but I get more stutters than with the goggles 2.
@LowNKum 17 күн бұрын
is it REALLY that much of a difference when you swap out the hotend fan versus say all of them?
@LowNKum 17 күн бұрын
I ask because i did the motherboard swap (yes I know soo late in the game) and my printer is literally next to my bed. Since the mb swap, LESS noise BUT again it's that hot end fan thats on full blast making all the noise, I also noticed the OE fan after a while will start to fall apart (my original fan lost 3 blades somehow - found out after it started making this loud squealing noise).
@Mangorille 17 күн бұрын
Yes, I found the hot end fan was the most noise, then the power supply fan. The drivers on the motherboard are noisy as well but sounds like you've already changed the motherboard out.
@richardruckert7954 18 күн бұрын
Why did you get b the G3? Better imager quality, more comfortable, in anticipation of 04?
@Mangorille 17 күн бұрын
Comfort and the real view cameras. The O4 compatibility is a big unknown right now since we don't know when the O4 will be released and even if the Goggles 2 / Integration will be compatible.
@SonmerfieldWendell-e4q 18 күн бұрын
Walker Linda Williams Betty Anderson Eric
@aarondodson1261 18 күн бұрын
My betafpv naked gopro is 28 grams
@Mangorille 17 күн бұрын
A naked gopro is very susceptible to damage in crashes on larger quads.
@aarondodson1261 17 күн бұрын
@@Mangorille that's why I wrapped it in tpu
@SbangFPV 18 күн бұрын
I haven’t updated any of my o3 au yet.. everything seems solid to me
@Mangorille 17 күн бұрын
Which goggles you using?
@SbangFPV 17 күн бұрын
@@Mangorille goggles 2
@SbangFPV 17 күн бұрын
That’s why I don’t need it.
@Mangorille 17 күн бұрын
@@SbangFPV Ya, it works fine with the goggles 2.
@MindRiderFPV 18 күн бұрын
Are you using the controller 3 or what? Interested to see how the whole DJI system works with the controller too without additional RX
@Mangorille 18 күн бұрын
I used to use the DJI Controller up until the Controller 2 and then decided that it was best to switch over to a dedicated control link when they started to really cut corners on their controllers. I ran the original black FPV controller for years but then started having problems with the Controller 2. I run the Tango 2 with an internal ELRS module now. Made a video when I switched over at the time: kzbin.info/www/bejne/h4PTeWaZbqxgj5Y
@MindRiderFPV 18 күн бұрын
@@Mangorille Thanks for the reply. Same here. Still on the old V2 / AU wondering what to switch to now and if the simplicity of the old system evolved. Apparently not. Curious to see the C3 with the new update? Thanks for the video!
@kaosvalentine 18 күн бұрын
I have a bit of a noob question. What would give me a better flight time for cruising on a 2 inch GepRC rocket plus with a naked GoPRO. The 650mah or 850mah 4s? Logic tells me 850 has more capacity. But weight I'm assuming also plays a big roll
@Mangorille 18 күн бұрын
Your logic is correct, but you also need to be mindful of how much that quad is going to weight once in the air. A 2 inch can only create so much lift and a 850 4s plus a go-pro is a lot of weight. It'll fly but will most likely handle terribly. I've seen folks using a 450 mah battery on that quad.
@ha-media 18 күн бұрын
Thanks for the test
@Mangorille 18 күн бұрын
Welcome. Happy flying!