That sediment bowl used as a sight glass to measure the oil flow is brilliant! Best I've seen.

Nice job...did i miss you cleaning the groves in the armature commutator?

You’re adding capacity by hooking 2 5 amp/hr to get 10, what you want is more current, (amperage) to get more grunt. When you increase voltage you decrease amps. A 10 amp/hr battery has more capacity in run time over the 5 , not power. The power would increase by wiring the batteries in series , pos-neg, neg to pos. Now you have more power. It would eventually burn out the motor, but not for a long time considering how short a Burst it actually runs to start the bike. The way you were doing it you were just making a bigger battery of the same power.

I have a question I have 2 30lb minn kota endurance trolley motors and when I hook them up to the battery the gears work opposite so when I put it 1st gear forward it moves the boat backwards and switch to 1st reverse it moves the boat forward both motors do exact same thing

Anyone making something similar commercially for the consumer?

Found this video after searching for a fix to my 2008 Ford F150 radio which would not de rease in volume. Was able to do this with som WD40 and it worked like a charm. Thanks so much

What do you suggest to someone who doesn't have an air ratchet or torch? Please don't say find someone who does,no one I know does.

Jeff, hope the tides have turned in your favor my friend! Just found your channel and I LOVE IT, hope youre doing well and continue to make stuff for us to learn from. Take care

Great idea! I've had casters on mine but now I need to make the crank handle adjuster for them. Easy enough!

nice tractor.nice bake sesh too.

I blew out a VW Bosch coil with that exact tach model! Now running a Subaru 2.5 from 2002 though...

Mine is on a 2003 Newmar Diesel pusher on a Freightliner custom chassis. There is no pump in the tank just the sensor. My tank has 3/4(75 gals) and rocking it back and forth did nothing. I'm wondering if my scan D gauge can be used to get a good estimate of remaining fuel as I've heard the labor to drop the tank and replace the sending unit is 1,000.00 plus the part. Thanks for posting this.

Well done, i might need this some day, own three of them

Very nice job

Thx

Hi thks for your videos may i ask where you buy the VFD please and the elec motor for the brill press and chuck thks

Will using oil on panels damage fibreglass areas, like from previous repairs?

The way that drill works I wonderif you eased the trigger if it would start cranking it over then speed up the drill.

Everytime of year I think of you thanks for all your knowledge RIP

I loved seeing the snow come down in the background window

That was exactly what I needed to see. I have that exact troller motor and ive started doing some of the things you did. However, I didnt know about the brushes, or those 2 pieces that have the wore attached to it. Ill sand it just like you did and see what happens. Thanks a lot showing your video.

Tapping into the fuel line... Brilliant. I can only shake my head (about myself) remembering the hundreds of times I've needed mower fuel, got a fuel container and drove to the gas station. Likely burning more fuel than I use mowing. Time to tap a line!

Thanks

worked for me, used a piece of shrink tube ,sized one end with 1/4" drill bit for tight fit on pot knob and just shrunk other end over snout of spray can. fit perfect and now volumn works like new, thanks again

This tip is a gift, I had been driven demented by a dodgy knob, one squirt and all good again!!!! Big thumbs up.

What a Champion. Tore mine apart, and had the exact same issue. Works like a charm now

Just fixed my Newport Vessels trolling motor (46 lbs.) using the video as a guide. The spring mechanism was slightly different but otherwise this guide was very helpful. Thanks Jeff.

always enjoyed checking out your videos (and learned something). Hopefully things will get better for you. Suggestion towards any healthcare: setup an appointment with a "specific seasoned specialist" at a large Research University Medical Center with a large endowment and excellent ratings (ie: University of Wisconsin Madison--Highland Ave Hospital). Could make a big difference with any major healthcare issues.

just fixed mine ! thank u

great job.......imagine vehicles using Z-bart or other hard undercoating......they would be in the junk pile instead of looking like new.

Please remake a new vidio of your Truck in 2024 this Vidio looks old can't find Date made

Very satisfying. Is that weird? Thanks

R.I.P. Jeff you where a good man.

My prop is froze up and won’t turn on the same model motor in video I’m thinking it’s brushes or armature bearing any input on this issue is appreciated

I wish they would have had you available when I was growing up that's all I can say

can you use this mixture on the break line nuts and brake fluid flush nuts?

I’m curious about your mod that allows you to mount your mowing deck without swapping out the 3pt arms. Thanks!

Cheer up Jeff

So if I tap on my lower unit and it works, I should do this eh?

how do you determine which direction the engine needs to turn

The electric bench has a sink?!

I'm a fan.

Love the 350X, I have a 83 200X and a 82 250R. I stumbled on to this channel today. . Your invention is really cool.

Great video. Very useful for my project

Best blade sharpener ive seen.

If you need a new variable speed pulley or sheaves, Speed Selector makes pulleys that replace the Reeves, Hi-Lo, TB Woods and Lovejoy pulleys that went out of business or got bought. Most are in stock or Speed Selector will custom make if needed. They have an actual engineering department; very helpful.