I got it disassembled but how do I reassemble the motor?

People who create these kinds of useful videos are heroes of humanity. Thank you for this.

Thanks so much!

Very helpful, thank you very much 😀

thanks bro!!

Worst design ever....I can't even find a screwdriver to fit in the holes to take the grill off.....awful. they just want you to buy a new one, smh

Is it possible to remove the blades from the motor? Or did I miss that part?

2:00 too bad u skipped this essential step. Unseating the green grille from the housing. What did u end up doing to knock it out of place?

Thanks! This is a public service. I'm lazy and just took off the front cover. I run the front cover in the shower, and the rest of it, a damp microfiber rag and a air compressor to clean out.

Hi, could you please confirm the model number with me ? I have DMW607W. I am trying to find its turntable but unable to as i its quite small. if you could please tell me the diameter of the tray i 'd be very thankful to you

Thanks for the video. What size of screwdriver fits the screws to take the outer grill off? Mike

I used to take it out in the sun and hose it down then let is sit outside in the sun and wind for a few hours. Worked like a charm.

Thank you! ❤

Impossible to open!! It should be easier. My screws are stripped.

First question where do I find a screwdriver long enough. And two why is the video so long? I’m trying to get my fan to work again, it’s hot lol.

I've had this fan for like a year and for some reason, they hid the screws in just the right way where I could never figure out how to open it up. For a while I just assumed they sonically welded the plastic or something. I was considering just buying a new one, but I figured I'd look up the model number, and your video was the first result. Huge, huge thanks for covering my blind spot with this one 😅

😂😂😂😂how do you clean??? The best part you don’t show 🤦🤦🤦

El mío no enciende 😢 Hay manera de repararlo

2 of the screws refused to pull out

If you have the tools it’s good to learn how to make replaceable ones last- comes in handy w more expensive ones too

None of my Phillips screwdrivers has a shaft that is skinny enough and long enough to reach these screws, so I’m stuck using pipe cleaners to get the gunk off the fan blades and the vent grids. I looked for this video to see whether a regular person was actually able to reach these screws and, more importantly, get them back in through those deep wells. Even if I buy a long enough small Phillips, I’m afraid I won’t get the darn faceplate back on.

Even the inside filter can be further opened. there are holes on the periphery of that, softly press a thin screwdriver in it, and tilt so that slight pressure is applied on the filter, then another gap will start opening up, put another screwdriver in that or even put your finger nail and twist, the upper and lower portions of the filter will separate, you will find a lot of calcium solidified in that. clean that with some cloth of metal. To reassemble, just put them together and slightly press, they will become assembled again with a click sound. It wouldn't break.

Thank you for this video! I was looking for a video to see how to clean mine like this one. I feel so stupid now. I kept fighting with it trying to get the 2 parts apart with no luck.😂

OH MY! So, I pulled out only the blades and now the fan won't come on? I didn't unscrew any of the inner screws, the fan just slid out, but after cleaning and putting back together, it doesn't work, sad. WHY?

Love the fan but it’s the WORSE to clean. I’ve bought 3 of them because the clean up process gives me a headache, but we are going to try to clean it todah

Great explanation and demonstration. Your comments, as you proceeded, were VERY helpful. Thanks!

TYSM 😊 I'd have never foud those tiny screws without your help I was about to throw it away lol Tnx for the time you took to make this vid 👍👍

I just cleaned out one of these and have another one to clean. I didn't unscrew the Motor or anything like that but between some Cleaning Wipes, a Tongue Depressor (for cleaning through the Grillwork all over), Popsicle Stick (to get the tinier areas) and some Canned Air to get all around the Motor and those parts, I got it pretty clean. It was starting to make a little rattling noise before I cleaned it, but afterward, it runs so nice and quiet, just like it did when I first bought it! 😍

why you had motor out you should of put a couple drops on front and Back( a little trickier) bearing felt area, just let it drip , a few times down shaft into bearing felt for rear ~Its critical to making these last a long time

OMG ! I used Vaccum and then Blower to clean up; still messy sticky web and dust. You Tube Guru rescued me . Thanks for sharing. In fact for everything; it is good to check youtube and then start do it yourself. You are a good guy. Thanks once again.

So unscrewed the stand from the entire fan, and managed to screw it back but it won’t do that “tik-tik-tik” sound when adjusting direction. Help!

One of the screws for the face plate is stripped. Suggestions so I can remove it? Thanks!

I have the same exact fan,it was all dusted and furred up from my cats hairs.Mine was making a vibrating sound so I wanted to take off the fan blade but I don't know how to do it. Does anybody know how to take the blade off of this fan?

I have 2 of these fans and a smaller one also and they’re the best fans I’ve ever had. Thanks for your video; it was very helpful!

Just needed a smooth blast of compressed air to do 80% of your work. The real thing lubing up the bushings you missed totally. Thats the most imp thing. Can be done easily with a long spout and SAE20 or 30 oil 2 drops.

Isopropyl alcohol for cleaning around electricity the only thing to use actually because it evaporates it doesn't stay wet for long

I can’t a thin screwdriver to fit the damn hole!

Seems silly you can’t remove the fan blade from the motor assembly

After spending about 45 minutes trying to realign the screws in my fan after watching your video it was so simple thank you so much save me a lot of time and my fan is working perfectly. Great video. Appreciate it greatly.

Great video Can you do a ceiling fan replacement video?

My fan cover is too hard to take off; compressed air for me. Lol

Just in case, anyone needs this information. The Honeywell HT-904 needs a Philips #1 screwdriver to remove the face plate.

*Bought this fan for the summer and so far it works great **Fastly.Cool** ! It's very quiet and not too loud, but also acts as a "white noise" when I go to sleep. No complaints from me!*

🤩

I have other fans that have pressure gripping devices for screen, it is so much simpler. Your video was very helpful. Thank you

Thank you. I appreciate your guidance.

Hey man, thanks for putting the appliance repair videos out. I started fixing stuff during lock down and now I’m getting into appliance repair. Learning as much as possible and your videos are the best ones I come across. Preciate it.

💪😃👍

Why didn’t you take the blade off first? Just wondering.

Great Job! After a summer of non stop running at the bottom of my desk, yeah its time for a cleaning! Thanks for the how to on taking it apart and back together!