Hello sir. I currently having a problem with Vs 640. can i contact you thru email?
@northcreativedesign2 күн бұрын
You had new head caps on. Can I still do a head soak with my caps being used? I just swapped them out in January. My cyan is clogged up from a company move we had to do and it sat while we were moving and getting set back up. ALso, are you using the TR2 Cleaning Solution?
@reprint217Күн бұрын
You most definitely can with used caps. I find the oem roland solution to be most effective.
@OscarPantoja-r4t5 күн бұрын
Hi. By any chance, do you have a video on how to do a cap ink pull with a syringe on a SG300? I did a few head soaks from watching your videos. But my cyan still has a couple of clogged nozzles.
@reprint2175 күн бұрын
That cyan is a nitemare. I don't recommend using a syringe on them heads as it can mess up them dampers.
@OscarPantoja-r4t5 күн бұрын
@reprint217 Is there anything else you can suggest I do to try and get the nozzles back, before I have to replace the head? I've been trying to get my hands on a service manual so I can change out the head myself. But I was told that without PECK code, I wouldn't be able to do the service on it myself. Im guessing that something only Techs have access to.
@joeyperez7286 күн бұрын
im dealing with the same thing rn lol
@reprint2175 күн бұрын
How is it going? Getting any better?
@robertserbin16 күн бұрын
Where are you located?
@reprint2175 күн бұрын
Springfield Illinois
@MaryFarnell7 күн бұрын
Hi, Yes tried this with 2 machines. It allows me to change the date, but reverts back to the original date which was previously set. How do you manage to save the setting as it is not on the video.
@reprint2177 күн бұрын
I see lots of people that is happening to. Try removing battery from mainboard
@imagfinder7 күн бұрын
Mike, thanks for doing these vids! I was able to change the cyan/magenta head on my SG-540, but now Im getting an alignment issue. It's like the black isn't lining up and the image is fuzzy. What would be the next step to stop that?
@reprint2177 күн бұрын
You need to get into service mode and do alignments
@imagfinder6 күн бұрын
@@reprint217 I figured it out. The head wasn’t pushed flat. I had to use a little more force than I expected. Once in position correctly, everything works as it should. Thanks for the help!
@georgewilson55219 күн бұрын
How long can I print head go without printing on average.
@reprint2177 күн бұрын
Depends on if it's plugged in cleaning. Too many variables
@georgewilson55217 күн бұрын
Water went into my motherboard so I had to buy another one during that time the printer was off but I always poured the cleaning solution every week or 2 can it go more than a year a still print again once my mother board is sorted.
@Pit-brothers12 күн бұрын
So my vg 540 just quit printing in h1 and h4. I have replaced all cap tops and idk what else to do
@reprint2177 күн бұрын
Is it throwing any error code? Text me 217-413-2532
@rowdieembry956213 күн бұрын
Thanks Mike, this info is CRAZY VALUABLE! Life Saver!
@reprint2177 күн бұрын
My pleasure!!
@KWANTlZE13 күн бұрын
can you help me whats your email
@cedomirburilo379617 күн бұрын
Hi Mike, I have a Sp540i and 6 months ago I replaced both dx4 heads and both cuptops. Now the test shows me that I have several shifted nozzles on black and blue. I do manual cleaning regularly, but it seems to me that more and more nozzles are not in place. What should I do?
@reprint2177 күн бұрын
What ink are you using?
@JcSilentSnake18 күн бұрын
Replaced the head on my sg540 dont know how to add the head rank or wjere to find it.. i bought the head on digiprint .im also. Stuck on a message that says canceled to protect pump..please help
@reprint2177 күн бұрын
Did you ever figure out? Sorry have been busy moving to new store front. Feel free to text me 217-413-2532
@JcSilentSnake6 күн бұрын
@reprint217 Yes, I got it thankyou..the only problem I have now is a message that says head protection activated when I turn the printer on. It pauses on each pass when printing, but if i print in service mode, it prints fine..im.hoping it's because I am using digiprint ink
@jimmyabdoojimmydoo764519 күн бұрын
Hi there. Thanks for your video. After I change the year in date change mode what button do I press to save the change. Each time I change it it reverts back to 2024. Thanks for your time
@reprint2177 күн бұрын
Try removing battery from mainboard
@jorgevale346719 күн бұрын
. I have set year to 2022 but the printer keeps reverting back to 2024. It doesn't seem to save the setting. Any tips?
@jimmyabdoojimmydoo764520 күн бұрын
Hi there. I have set year to 2022 but the printer keeps reverting back to 2024. It doesn't seem to save the setting. Any tips?
@reprint2177 күн бұрын
Try removing battery if it's resetting back that usually means your not in technician mode
@Mcmiddies22 күн бұрын
Hey man. Thanks for all your vids. I am looking at buying a used Roland True Vis VG640. Is it easy to factory reset? They say it was pulled from a working environment. Its an older machine but I am just getting started with this and its a good deal from a good source. What do you think?
@JcSilentSnake24 күн бұрын
Im stuck with a message that says " cancled for pump protection" how can i fix this
@reprint2177 күн бұрын
Usually have to let sit for a bit and try again
@JcSilentSnake5 күн бұрын
@reprint217 thanks..it was a low ink problem after I put in a new ink it went away but now I'm having a "head protection activated" message..I'm hoping it's because of the ink I'm using which is digiprint ink
@betterprinters24 күн бұрын
Do you think I would be able to replace the cyan printhead myself? and where do I get it? I may need your assistance.
@reprint2177 күн бұрын
Feel free to text me 217-413-2532 gladly help you through it
@JcSilentSnake25 күн бұрын
what size syringe are you using??
@reprint21725 күн бұрын
Whatever I can find lol. Usually 20ML
@JcSilentSnake24 күн бұрын
@@reprint217 thankyou
@JcSilentSnake15 күн бұрын
I installed a new head on my sg-540. I got it to print black, but It won't print yellow. Do you have any idea the cause ??
@SethCampbell-zr8bq27 күн бұрын
Can we get a link for the dampers replacement?
@gustavocorrea401729 күн бұрын
Hey, I'm looking to buy heads and cleaner but the page isn't working. How can I do it? Thanks
@reprint21725 күн бұрын
Printholix.com
@andrewevans3963Ай бұрын
Any videos that would show a way to get to this point cleanly, so I could get a full break down of start to finish. Thanks for the vid
@reprint2177 күн бұрын
Unfortunately I just make videos on the fly. Don't have any mimakis at the moment
@user-so8eg1fc3yАй бұрын
thank you for making this video
@reprint2175 күн бұрын
My pleasure
@pengcui13Ай бұрын
it is nessary for Newbie one to learn software form this video
@reprint2175 күн бұрын
Yes it is!
@BigGuyPDSАй бұрын
Hello. Thanks for the video - very helpful. We just replaced one of the print heads on one of our XR640s. I failed to save the packaging and don't have the head serial number. However, I did take photos of the head and there are numbers on it. Is the serial number on the actual print head? Just curious. If not, is there another solution or work around for this issue? Thanks in advance. ~Tim
@reprint217Ай бұрын
Yes those would be the numbers you input!
@RAYAN-lt3gvАй бұрын
Sire, how i can connect with you?
@reprint2174 күн бұрын
217-413-2532
@visprosignsgraphics1443Ай бұрын
Are the DX7 printheads for Mimaki CV150 from DigiPrint supply good?
@reprint217Ай бұрын
Ive had good luck with digiprint they are my go to
@visprosignsgraphics1443Ай бұрын
Where do you get the CJV150 oem printhead? I currently need one. Thanks!
@reprint2173 күн бұрын
Usually Digiprint supplies
@lxstangsАй бұрын
Why not just open it and take the gelled stuff out then flush
@klintonbarnhill7002Ай бұрын
Nice video!
@McmiddiesАй бұрын
Hey man, I am looking at buying a roland true vis vg 640. Can i print from any software? Or do i need to use roland software? Any tips you can give me? I found the website you use for parts unless you found a new one. Any tips would be appreciated. Thanks man and keep up the videos.
@duyetnguyen-zz5odАй бұрын
What happen if the arm is not moving at all to the left or right. (Arm on yellow)
@reprint217Ай бұрын
It is either full and not suctioning properly or it is not filling up properly
@duyetnguyen-zz5odАй бұрын
How do I go into service mode with my VG640 I already got page 10 on number 1. But the second step: Down right left up then: right down left then: hold right down left press power button. It then say: service mode is protected. Could it be different for the VG640 version?
@toptaximedia7486Ай бұрын
Hi dear where can I order this new head and what is the refernce number Thank you
@duyetnguyen-zz5odАй бұрын
I have a VG 640 and I have lost yellow ink lines showing on my print test patern.
@reprint217Ай бұрын
Probably need to do a damper fill
@duyetnguyen-zz5odАй бұрын
When I’m doing a clean..I don’t see the flag is moving for yellow ink. (The flag that supposed to move in and out when it pumps the ink in. I’m pretty sure there is nothing wrong with the print heat. I had it very good just 3 days ago. All lines are perfect. Because I rang out of yellow ink the other day..so I cut my yellow ink bag and refilled it with the left over I had. My yellow on the left is gone now. But the second yellow is still working. Still printing cos my printer print setting CYMK 4 color with 8 ink bags using 2C 2Y 2M 2K. How do I get the flag to move again. I think you call them “arm”
@moonrakercatАй бұрын
I'm impressed - you really know these print heads - Finally someone who knows their *hit !!! Keep up the good vids Mike- I really appreciate them !
@moonrakercatАй бұрын
Good informational video - thanks Mike !! Quick question - have you ever disconnected one of the ink feed lines into the top of the dampers and then inserted a line from a syringe filled with cleaning fluid - and slowly pushed on the syringe to carefully force cleaning fluid through the head to fix nozzle drop outs and deflections ???
@reprint217Ай бұрын
Please steer clear of this method on the dx7. I only recommend as a last resort with any epson head. Pressure will likely cause the nozzle plate to come loose
@moonrakercatАй бұрын
Hey Mike- I know the captops are important to seal for the pump to pull the ink - but have you ever replaced an ink pump ?? do they ever go bad ?
@reprint217Ай бұрын
They most definitely do go bad, not as often as other parts but have replaced dozens of them.
@moonrakercatАй бұрын
@@reprint217 OK - thanks for the feedback Mike. It seems I'm replacing captops on my vs 540 every 3 months - and even when I replace them it's hard to get a full nozzle print again - I've tried and tried to adjust the cap top placement on the head - it doesn't seem to do much. My ink pump still pulls ink - but I'm thinking it might be weak and contributing to my excessive cap top replacements. My machine is 13 years old - and in great shape. I might look into replacing the pump. The captops are getting expensive. I've never used aftermarket parts or inks.
@moonrakercatАй бұрын
Good video - I have so many problems like this with my print head - I usually adjust it manually with the screws - I need to look into the service manual - I'll send you an email -- would appreciate it if you can send it - Thanks - Matt.
@reprint217Ай бұрын
I Sure will
@RomanK87Ай бұрын
Hi friend, for BN20 if I'll need to change printhead, is it simple to put in new, or I need to program it somehow? What's the process?
@marcusrcoatesАй бұрын
Hi I have an sg300 with no yellow filling the damper. Is it the same process, put a syringe on the yellow line that feeds the damper and pull to draw the ink? Thanks
@reprint217Ай бұрын
No! Pull from the captop
@ExplosionLoliАй бұрын
Can i email you? I'm having some weird issues with my BN-20A. Could definitely use some guidance 🙏
@janniss.3004Ай бұрын
Hi, I just got an old vs420 which has some ink head problems. Could you sent me the service manual you mentioned? regards
Great videos! How do you clean the ink lines at the damper end? I try to draw it out without the damper on and nothing comes out of 4 lines. (2 magenta, yellow and maybe light cyan) I replaced all my ink lines when I switched from white/silver to cyan/ magenta but I still had problems. Unfortunately, it sat for the last 6 months (kept getting error code 0109 and spotty inks). I have continued to keep the head soaked so I believe that is fine, I do not have the choke installed any more ( the tech when he replaced the lines disconnected it) but all the parts are there if I need to reconnect.
@reprint217Ай бұрын
Have you pulled your lines from the ink needle? Possibly the needles are clogged in the cartridge bay
@reprint217Ай бұрын
Also, I have had machines with the choke valve bypassed, have seen this many times and be very careful when messing with the head. I choked one off and assumed it was choked and destroyed a brand new head.
@amymednick3661Ай бұрын
@@reprint217OOOHHH! I never thought of that!! I will check. Thank you!
@amymednick3661Ай бұрын
@@reprint217 unfortunately I do not have anything small enough to go over the needle. Do you have a suggestion for the tubes that attach to the damper top?
@hand5man658Ай бұрын
I tried that page 10 is set to 1 but when i turn it on it's not show the service mode
@reprint217Ай бұрын
Than you likely need to update your firmware
@hand5man658Ай бұрын
@@reprint217 ok thank you i will try it was version 1.10
@QHIKINDUSTRIESАй бұрын
how do you move the print gantry without putting it in Manual cleaning? like how you are able to move it around freely?
@reprint217Ай бұрын
On the Truevis units with the power off, push carriage to the right to unlock head carriage
@dynastylifestyleNPАй бұрын
Hey I see you dealt with the STS VJ-628D-C, do you think it is worth buying? I have a guy on Facebook market selling for 1800 but needs print head which I know is expensive in itself
@reprint217Ай бұрын
I see them all over anymore, and I personally would have to pass. The dx7 isn't a good head for dtf and likely would have to replace one every year. Plus, the machine is way to slow. I'm not even sure if I would fix it, if was given to me for free.
@dynastylifestyleNPАй бұрын
@@reprint217 thanks for replying. Do you think dual xp600 is a better option for speed and quality aka chinese machine lol
@ProtestDeNiroАй бұрын
Hey Mike, I tried the syringe cleaning technic and after one channel of the printhead came, I sealed it so that it only pulls on the clogged channel. Problem now is, both channels have 80% of the nozzles working. But the last 20% just wont come because the syringe is filling up instantly via the open nozzles. Any tips on the last 20%? thanks in advance
@reprint217Ай бұрын
Usually a rinse and repeat process of soaks. Or now that it is mostly broke loose, gently syringe the head
@ProtestDeNiroАй бұрын
@@reprint217 can I pull with the syringe on top of the head (where the dampers sit) while there is solvent in the captops? Or would you just push?
@NugemartАй бұрын
To get out, you have to go back to the item 10 and chsnge 1 to 0