The maximum heating temperature depends on the version ordered. Most silicone rubber heaters have a maximum temperature of 450°F (232°C). You can order the SRL or SRP heaters with a 150°F (66°C) high limit switch which will limit the temperature. Keep in mind, heating blankets require a temperature controller. The -ADJ versions have an adjustment to reduce the supply wattage; however, it can not be set to a specific temperature. For vinyl, you should use a temperature controller to ensure it does not go above the melting temperature of the material. Our LYNX-SET (PID), TB250N-250, or SDC are good options.

Hello SpringWell Thank you for the question. The simple answer is yes as long as the amp load does not exceed the wires amp capacity. 12/2 wire is rated for use of up to a 20AMP circuit. The TB250 has an maximum amp capacity of 22. Regardless, if you do not exceed the 20amp capacity of the 12/2 wire, all will be fine. Thank you

For safety reasons, heating cables should not be sealed inside a wall or ceiling.

The TTD175-K120 is for 120 volt The TTD175-K240 is for 240 volt www.briskheat.com/ttd-outdoor-use-digital-on-off-temperature-controller.html Here is a link to the instruction manual. www.briskheat.com/mwdownloads/download/link/id/95

Whether or not it can be used for sublimation depends on the transition temperature of the solid. The heater itself cannot be used in an environment where it is exposed to extreme pressures and the application temperature is limited to 450F (232C). It is unlikely unless the phase change takes place within these limitations.

We offer many different types of heating cable. www.briskheat.com/products/heaters/heating-cable.html

Yes. Our silicone drum heaters are rated for continuous operation at up to 392°F (200°C). www.briskheat.com/products/heaters/drum-container-heaters/silicone-drum-pail-heaters.html

@@BriskHeat Much appreciated

@@BriskHeat Follow up question. Does it maintain a consistent temperature or does it duty cycle on and off to maintain a desired temperature? So if it's at 50% power, does it for instance turn on for 1 second, and off for 1 second, and alternate or does it remain at a consistent temperature without cycling off

Hi Stephen! There is an intake and exhaust fan on the hot bonder to keep the components cool. If you'd like more info, we'd be happy to talk! You can send us an email at [email protected] or give us a call at 614-294-3376!

@BriskHeat Corporation so Zone 2 has a fan...?

@@stephenszabo2361 Yes! One fan for the unit!

@@BriskHeat thank you

Hopefully this video can help you out. kzbin.info/www/bejne/a5ikn3-qdpyrhpY

The controller does not show the temperature. This is a dial controller that goes from max temp to off. If you need exact temperature control, we recommend using a temperature controller with more accuracy. Depending on your needs, you could use a PID temperature controller like our LYNX™ PID TEMPERATURE CONTROL SET

Hola. Puede encontrar el producto en www.briskheat.com. BriskHeat realiza envíos internacionales. Necesita cintas calefactoras flexibles BriskHeat.

Hi Brandon, I'm John Li with BriskHeat. I don't normally come here but was just checking out a new video and saw your message. Has someone replied yet? You can write to me at [email protected] and get more detail. Water is a slow heating material. If the water is in a 55 gallon drum and it's full it will take awhile to heat up, but if it's in a pail (we also have pail heaters) it's much quicker and you can enjoy a hot shower quickly.

jim Nicosia YES....

Get Frost electrical heat tape which looks like coax cable,make sure you put thermostat on the coldest part of pipe ,you can use zip ties or electrical tape....

kzbin.info/www/bejne/jJvNlqWdhLasbKs

Home Depot has a product that is all included and does the same thing.

is this true about in line or wrapping with most heat tapes that have their own built in thermostat