Пікірлер
@warzonewarfare2925 Ай бұрын
Hi, do you have the coding instructions too?
@alireza071 Ай бұрын
Is there any live wire i can connect my symphony lights to ? Can i use windows live power ?
@jamesgreen363 4 ай бұрын
Wouldn’t it have been easier to run cable through roof lining and front door pillar to fuse box ? About to attempt an install on my golf r . Found it easy to root cable for my rear dash camera that way 🤔
@neilgardner8794 4 ай бұрын
Hi are the pins the same on both doors
@andygardner3177 4 ай бұрын
@@neilgardner8794 they should be for both front doors
@stephanpieterse6960 5 ай бұрын
How would you ground to the car instead of cutting any OEM wires? Pin 5 alternative is what I am after. Please
@eagle56786 3 ай бұрын
the car isn’t connected to the door except thru the electronics. use a t-tap connector on the OEM wire if you’re afraid to damage it
@stephanpieterse6960 3 ай бұрын
@@eagle56786 Hi thanks for the response. I am using a Wago 3 pin connector instead so I never have to cut, pin or splice into OEM wires. Works a treat. Just hoping to confirm are both front door modules and wiring looms the same or do they differ?
@thespecialist786 6 ай бұрын
Hi, Did you have any issues of the display keeps disappearing and needing to do a hard reset on the main MiBII system? I see you have using the same 12v positive as the head unit did that work fine?
@andygardner3177 6 ай бұрын
@@thespecialist786 I didn’t have that issue, everything is still working perfectly.
@misat0san 9 ай бұрын
what a useless video “watch another video to see what to do”
@andygardner3177 9 ай бұрын
Assuming you mean about the coding via VCDS. I created this video to help a single person on a forum. This isn’t my job or anything just trying to help people. Sorry I couldn’t help let me know if you have any questions.
@thespecialist786 10 ай бұрын
I don’t get it, why is everyone showing the front door, what about the Rear????
@andygardner3177 10 ай бұрын
The rear on a golf doesn’t have a door control module unlike the A3. There is no easy factory like way to do it.
@thespecialist786 10 ай бұрын
@@andygardner3177 I did it like some say but still have 5v coming to the door after door closed. It does not drain the battery if driving everyday but if I leave the car for a week it may drain the battery. I will need to install a 12v regulator.
@GeorgMeier-l2q 11 ай бұрын
Guten Tag, ich heute Kamera eingebaut in ein Versand t roc und das Problem das die Kamera nichts anzeigt.Könenen sie ein Video machen wie es codiert wird. Danke
@brandolino55 11 ай бұрын
Video is not usafle😂
@andygardner3177 11 ай бұрын
Sorry I don’t understand what you mean by usafle?
@aajjoel Жыл бұрын
Great vid, I am just having problems to fit the red wire in the fuse box. Any tips? Also how many Amps fuse do I need ?
@andygardner3177 Жыл бұрын
Are you trying to use a piggy back/fly wire device or fitting the fuse way in? I have a 7.5AMP fuse in. I think i picked this size based on the factory wiring diagram so it's the same size as if car came with the camera.
@aajjoel Жыл бұрын
@@andygardner3177 thanks. I did it with a piggy back now. Works like a charm :)
@shafzabid Жыл бұрын
Excellent camera work 😮😮😮😮
@andygardner3177 Жыл бұрын
Hi, Sorry about that, let me know if I can help in anyway🙂, this is just a hobby, stuck it together to help someone on the forum.
@martynstoychev98 Жыл бұрын
Hello brother i have bought wiring for my rear camera but it doesnt have the orange splitter in your video how can i bypass ir
@andygardner3177 Жыл бұрын
Does it have two orange wires?
@РоманКубрак-с1ч Жыл бұрын
Неймовірно, але це спрацювало! Біос HP Elitebook 840 g2 прошивається через прищепку! Величезна подяка автору!
@mariejosado Жыл бұрын
How about adding the speed cameras alerts to the GOlf Mk8?
@andygardner3177 Жыл бұрын
Not sure don’t have a mk8 to play with 😊 try looking for MIB3 speed camera (that’s the name for the head unit)
@andygardner3177 Жыл бұрын
@@HassanAhmed-qy8jw andysome2021
@brathishan5611 Жыл бұрын
Hi, great video. Is the coding the same for Golf mk7.5?
@andygardner3177 Жыл бұрын
Hi, I am installing to a 7.5 in the video. The coding is the same.
@leijiao1074 Жыл бұрын
Hi Andy, great video! planning to take on the project myself for a 2019 eGolf (w/ Discover Media). I have a few quick questions.. Do you find the quality of the camera up to the standards of "OEM"/original? or do you think the OE camera from VW will be better quality? Regarding the wiring of this version (highline), there is no need to tap into the reverse light because of the canbus connection, right? My understanding is that there are just 2 canbus wire, 2 video wire, and a 12v power to connect at the back of the MIB unit. (Is there a ground as well?) Any tips on how to pick up the 12v power from the red wire without damaging the original wiring? Thanks!
@andygardner3177 Жыл бұрын
Hi, The camera looks as good from a visual compare with a friend. You are correct with highline there is no feed from the light. The ground is taken from the car wiring you plug into in order to open the tailgate. The brown and purple connector shown in the video. You can take it put it into the fuse board but this is hard or use a fuse "piggy back"
@leijiao1074 Жыл бұрын
@@andygardner3177 Thanks so much Andy, fuse "piggy back" sounds great! I guess for us UK cars we just run the wire on the left side and we can access radio and fuse box without wiring going through the middle?
@andygardner3177 Жыл бұрын
@@leijiao1074 yeah that’s right down the side and then up 🙂 Same for the US they just do the other side.
@leijiao1074 Жыл бұрын
@@andygardner3177 Great, many thanks! appreciate all the info. I will order the camera now :)
@kasten8020 Жыл бұрын
@@leijiao1074have you installed the camera I want one to in my egolf 2020 Do you need to Programm the camera itself with vcp? I only have VCDS
@-JPS- 2 жыл бұрын
Hello, greetings from Spain. my camera shows error B201000. Does it mean that it is not parameterized? or what is missing to calibrate? Do you know if it can be done in obdeleven? or vagcom? Thank you
@sofianemeryoul8128 2 жыл бұрын
Hi my friend please I want to ask you, the higline reversing camera retrofit have 3 or 4 deferent mode of view, I want to ask those options of view into the camera or you need to change some unit on your car to get it?
@andygardner3177 2 жыл бұрын
Hi they can be coded in, I have them coded in. If you follow the coding in the description they are there.
@sofianemeryoul8128 2 жыл бұрын
My friend , I just want to know the options into the camera or the unit of the car , by the way install it in my car but I not have those mode of view the car seat Leon mk3 cupra, I am afraid 😟 my unit not have it that all if I have have to change the camera I will do it no problem 😊
@oetamsoetams6827 2 жыл бұрын
Hello, I have an HP Elitebook Folio 9470M (made in 2016) that has a locked BIOS and wondering what procedure you recommend to clear the BIOS password? I have been looking at using your test chip clip method to modify the BIOS using the RCUnlocker tool? Do you advise this utility one or another for my model?
@Malkit210490 2 жыл бұрын
I'm in birmingham. Could you help me install these lights?
@Malkit210490 2 жыл бұрын
Tried your instagram handle but not found.
@Zattoo20 2 жыл бұрын
NOW 199,64 ￡ WTF
@AlbanianBl00d 2 жыл бұрын
I accidentally unpluged the parking sensors module when i was installing reserve camera on my golf mk5 and now my parking sensor are not working any solution pls
@a1pro2003 12 күн бұрын
Plug it back in 👍
@Hmadan93 2 жыл бұрын
This one work with radio 5G0035819A ??
@andygardner3177 2 жыл бұрын
Hi, No it doesn’t.
@adel0king 2 жыл бұрын
hi, this method can be apply on hp elitebook 840 G1 ?
@ashwin372 2 жыл бұрын
yes
@Luka-ov1hu 2 жыл бұрын
Lights only work at night ?
@andygardner3177 2 жыл бұрын
They work all the time but can’t be seen in the day.
@nav01nav 2 жыл бұрын
Can you use vcds lite
@giwrgosathan1776 2 жыл бұрын
Any news about calibration?
@andygardner3177 2 жыл бұрын
I haven’t looked at it because it’s so close. I might get round to it at some point.
@saifhashid 2 жыл бұрын
Hi mate, is your logo blue and white or black and white? I prefer black and white. If you have the link can you send it pls
@patrickbeukman3769 2 жыл бұрын
never use the blue and red scotch block !!! always solder!
@andygardner3177 2 жыл бұрын
I partly agree and it’s certainly a more reliable connection, but it excludes people and it’s easy to make a mess of especially if your forced to do it in midair etc. I’m okay at soldering but for car electrics I often chose connection blocks or repinning adding to wires two the connector. People sometimes want to be able to remove mods without stuff being super visible as well.
@jockesgarage6049 2 жыл бұрын
I got a oem on my car. The screen i black when in turn on reverse. I have a new camera installed and it not work. fail code no signal
@bootlegnation1948 3 жыл бұрын
Thanks for the video mate, Is there anywhere you can go to get this done? I just don’t trust myself haha!
@andygardner3177 3 жыл бұрын
Are you anywhere near notts or brum in the UK
@bootlegnation1948 3 жыл бұрын
@@andygardner3177 I’m Essex so about 2 hours away, i don’t mind a drive though!
@andygardner3177 3 жыл бұрын
@@bootlegnation1948 happy to help add me on Instagram?
@bootlegnation1948 3 жыл бұрын
@@andygardner3177 really?! That would be quality! Thankyou mate 👍🏻 what’s your username?
@andygardner3177 3 жыл бұрын
@@bootlegnation1948 mrpandygardner
@eduardoretamales5139 3 жыл бұрын
hi, I have a question, do you need just the carista app for to apply the upgrade? Or do you need both, by the way carista app and vcds? . I have another question, the carista app , is con crédit or free?. Thanks !
@andygardner3177 3 жыл бұрын
Hi you can use either VCDS or carista. No need for both 😀 you have to pay for carista
@markkofi8522 3 жыл бұрын
Both our cars, BMW X5 and Golf GTE, have reversing cameras. What I don't like about the VWs is that as soon as you take the car out of reverse, the camera cuts off. With the X5 the camera remains for a few additional seconds. So I still have a rear view as I edge forward.
@andygardner3177 3 жыл бұрын
Is it not disabling based on speed?
@ThoNguyen-nw6bq 3 жыл бұрын
Character In the video It's great, I like it a lot $$
@sharkice 3 жыл бұрын
Hola , podrias pasar el software para programar la bios ! gracias !!
@eduki 3 жыл бұрын
That´s awesome, thanks for the video and the full info at the description! ;)
@andygardner3177 3 жыл бұрын
Your welcome let me know if you need anything else. I’d recommend buying the same camera as me if your planning to follow along some have a blue wire not covered in my vid
@eduki 3 жыл бұрын
@@andygardner3177 I'd try to follow the DIY buying from the same store, thank you! ;)
@noz3m 3 жыл бұрын
Did you get the high or low line? if you did the highline, were you successful with the calibration?
@andygardner3177 3 жыл бұрын
High. There different “high” on AliExpress. Mine works like the official VW one. There’s a link to the one I brought in the description.
@andygardner3177 3 жыл бұрын
I haven’t dug into calibration.
@noz3m 3 жыл бұрын
@@andygardner3177 all I hear that it's impossible to calibrate it. Do you find it works good enough as is? So without the calibration?
@andygardner3177 3 жыл бұрын
@@noz3m I’ve printed the board but not got round to it the camera is pretty close I brought as it is. I can’t tell the difference from factory at a quick look. (Friends R)
@noz3m 3 жыл бұрын
@@andygardner3177 ah I see so the quality is nice? I like the highline camera but I won't be able to get it calibrated here. Don't have the software.. so not sure if I should get the low or high version. What do you think?
@BillRehbock 3 жыл бұрын
Hi Andy, great video. I purchased the same highline RVC from Heycar and fitted it to my NAR 2016 Golf-R with an (earlier retrofitted) MIB2 Discover Pro. I've coded things to what you've posted, and am 99% certain that I have the wiring correct for the KA2/highline (disconnected the right back-up light signal and routed the trigger wire from the camera to the badge-flipper, etc.). My issue is that the badge and camera won't flip open. I can see on the display that the camera is working and the lines are tracking the steering angle and the view modes properly appear. Could you please post the complete long coding strings that you are using for the RVC, 6C and Parking Aid, 76 (or 10)? Might be related: when I code my 6C with VCDS, the values for bytes 3 and 4 are 0 and the drop-downs don't list any model/variant data, so I need to type the hexadecimal values in. Thanks in advance. (By the way, I have heard that ODIS simply will not allow the calibration routine to complete on a Golf because the VIN will always mis-match and the Golf was never equipped with the KA2/highline camera. However, the values supposedly can be copied in using VCP so you can get rid of the "not calibrated" DTC.)
@andygardner3177 3 жыл бұрын
Do you have a blue wire going to the rear light? That works differently to the one I have and how the official VW one does. Some also just work on gyro not taking canbus data at all. Are you after low line or highline coding ?
@andygardner3177 3 жыл бұрын
Do you have a link to the camera you brought?
@BillRehbock 3 жыл бұрын
@@andygardner3177 I disconnected and capped off the blue/black wire from the camera that works its way back to T73a/64 on J519 (and the right backup light, etc. - my rt backup still works) and have everything wired for the KA2 highline, so I am looking for the R189/5GG 827 469 F highline coding and the Park-Assist module coding, too, just to make sure because one of the DTCs I get is: "U1121 00 [009] - Missing Message [message Parkhilfe_01 not received]". So my analysis is that either 6C is not getting the "Open the door" signal because of wrong Hex10/76 coding, or its misinterpreting the signal because of incorrect Hex6C coding. The thing is that we all know that the highline camera relies on CANbus to open the badge, but do we know which module is responsible for sending the command? And, by the way, the US Arteon and Atlas that I've checked both have 5F coded for "BAP VPS msg bus" set for Infotainment Bus, not Comfort Bus, which seems to be the generally accepted channel, so go figure. This is why I'm interested in the full coding strings.
@andygardner3177 3 жыл бұрын
@@BillRehbock some of the cameras use a blue wire to the rear light to know when to open the camera. They just don’t work like the official VW or the camera I brought. Can you share a link to the camera you have?
@andygardner3177 3 жыл бұрын
Does your camera have a blue wire if so it doesn’t work like the official VW one or this one I’ve fitted? They only use the canbus for steering
@eilonbenaim1487 3 жыл бұрын
Great great content! It will be awesome to see a vid of the coding and the part of the fuse box. Thanks!
@andygardner3177 3 жыл бұрын
The coding is in the description.
@tubeme4vr 3 жыл бұрын
Great video! The most I have installed so far is the Dashcam, front and back, with connection to the fuse board. How hard is it to install the rear view cam? what tools do I need?
@andygardner3177 3 жыл бұрын
The connection to the back of the fuse board is a nightmare it’s really tight and you need to pull the purple retainers out of the back of the fuse board. I used a piggy back fly wire fuse thing. Tools wise it’s trim tools, trox bits, a socket for the rear seat and tape. I also used a bit of strong wire to help with pulling the cables. I taped the cable to the wire then pushed it thru.
@tubeme4vr 3 жыл бұрын
@@andygardner3177 Hey Andy, thanks so much for your help. I fully agree with your approach. I saw some other videos but I don't know why they pull out the screen as well. It should be enough to get out the mib unit in the glove compartment. I sent you a Instagram connection request BTW 😊
@everythinghelp4u458 3 жыл бұрын
Hi Andy, great video. Helped me a lot! Thank you for this. Just wanted to ask if you managed to make the video on coding and calibration? Would really love to do it myself. I have a vagcom
@andygardner3177 3 жыл бұрын
The coding is in the description, I keep trying to get round to playing with the calibration. I have the giant domino printed to scale
@everythinghelp4u458 3 жыл бұрын
@@andygardner3177 thank you, must have missed it. I'll take a look now :)
@tubeme4vr 3 жыл бұрын
@@andygardner3177 Hello, did you manage to complete the calibration on your own?
@KasamS 3 жыл бұрын
So if i have the sill light id need to tap into that instead of pinning it to the plug itself?
@andygardner3177 3 жыл бұрын
Yeah and you won’t need to do the coding as it’s the same output. 🙂 I can send you the wiring diagram if you comment something I can contact you on
@jackvettese2617 3 жыл бұрын
@@andygardner3177 , sorry to butt in, but any chance I could get my hands on these drawings you speak of.
@andygardner3177 3 жыл бұрын
@@jackvettese2617 mrpandygardner is my Instagram
@KasamS 3 жыл бұрын
Whats the diffierence between vw and vw compiled?
@carlosb68 3 жыл бұрын
Great Vieo Andy. I would like see the parametrization video too. Carolco
@andygardner3177 3 жыл бұрын
Yeah the AliExpress link I used came parametrised. I haven’t got round to calibration as it’s basically already correct
@carlosb68 3 жыл бұрын
@@andygardner3177 Dont have any error in unit 10 or 76 unit ?
@macartanmcquaid22 3 жыл бұрын
Hi there, Thanks for the video, as good as I've seen 👍🏻 What I'm not sure about still though is the two orange wires and the red wire up to the back of the MIB2 unit. I think the red goes to the fuse box? It's not clear what needs doing to the two yellow/orange ones? Thanks again, Mac
@andygardner3177 3 жыл бұрын
Go on the pins and match the colour stripes and you’ll be fine on the canbus connection. Red is the +12v it can go into the back of the fuse box but it’s a right pain. I used a fly wire type thing.
@macartanmcquaid22 3 жыл бұрын
@@andygardner3177 Yeah, that's exactly what I ended up doing. All working well thankfully 😎
@eilonbenaim1487 3 жыл бұрын
@@andygardner3177 fly wire but where did you connect it to?
@AlexKingstone 3 жыл бұрын
Thx for video, very useful, any hints on coding and calibration?
@andygardner3177 3 жыл бұрын
The coding is in the description mate. Calibration I haven’t got round to as it’s close enough so it’s low on my todo list
@AlexKingstone 3 жыл бұрын
@@andygardner3177 thx mate! Somehow overlook it.
@AlexKingstone 3 жыл бұрын
@@andygardner3177 Camera installed, however getting below error on long coding "marginal conditions have not been met" seems camera is new and do not have basic settings :/
@kasten8020 Жыл бұрын
@@AlexKingstonehow did you fix the issue have the same problem
@AlexKingstone Жыл бұрын
@@kasten8020 Hard to say exactly what helped, but I was in dealership where they had ODIS ( official software ). They tried to code it but got the same error. Next day its simply started to work.
@aadamc8329 3 жыл бұрын
Hi mate, I was just wondering if you could make a short video of the quality of the camera etc. Thanks!
@andygardner3177 3 жыл бұрын
Do you mean image quality?
@aadamc8329 3 жыл бұрын
@@andygardner3177 yeah mate! Exactly that sorry I worded so poorly haha.
@andygardner3177 3 жыл бұрын
@@aadamc8329 this is in the dark ibb.co/S0NQZmM it’s pretty clear. Before I coded the other modes in.
@cosmin-mihaisurca3752 3 жыл бұрын
Hello, do you know if i can install hightline rear view camera, if i have on my car MIB 1?
@andygardner3177 3 жыл бұрын
There’s a list of part numbers in the description if you hold menu the part number will come up.
@dogg2828 3 жыл бұрын
Doesn’t work
@andygardner3177 3 жыл бұрын
What doesn’t work sorry? Had a quite a few people let me know they’ve installed with success.
@dogg2828 3 жыл бұрын
@@andygardner3177 it wont update my POI’s i have the exact same set up as you and have followed your instructions