1.Exceeding Vertical Angle Limits: The vertical angle of the Sokkia CX 105 may have a specified range, such as -30° to +90°. If the instrument is tilted beyond this range (for example, pointing too high or too low), it will display "out of range." 2. Incorrect Instrument Setup: If the total station isn't leveled properly or is set up on uneven terrain, it could report an incorrect angle, leading to the "out of range" message. 3. Calibration Issues: The vertical angle sensors may be out of calibration. If the total station hasn't been calibrated recently or has undergone rough handling, this could affect its ability to accurately measure vertical angles. 4. Obstructions or Reflections: If there are objects or reflective surfaces near the instrument, they may interfere with angle readings and cause the instrument to interpret vertical angles incorrectly.

@@gulabchikbaraik2331 jnb who bhi Hy channal py visit kro

@@PK-ty2wb welcome

Thanks very much

@@Radha32198 welcome

@@zahidsiddiquee7544 most welcome

Thanks

Thanks

Thanks

Thanks for the visit

@@muhammadayub3293 Ok

@@umerfarooq-zo2sn انشاء الله

@@HasnainAhmad-u8l light Waly button ko long press krny Sy

@@SurveyMentorWaqas thanku sir

@@HasnainAhmad-u8l most welcome

@@FarmanKhan-sb1bv بالکل سر خریدیں کیوں نہیں فرمان صاحب کا نمبر ہو گا آپ کے پاس ان سے رابطہ کریں مل جاۓ گا 😜

Kharid liya kya... Apne total station

@@VanshChoudhary-k5m نہیں

@@MuhammadHanif-hh5fk جناب آپ کو خریدنے کی کیا ضرورت ہے application ڈاؤنلوڈ کریں نا

@@AhmadAliKhan1129 channal visit kro apko video mil jaye gi. Is per pehly Sy video bana Chuka Hoon .

The process of finding the height of objects without actually going to the top of the object is known as Remote Elevation Measuring (REM) i.e., a total station placed remotely (faraway) from the object is used to measure the heights. REm Figure 6: Remote Elevation Measurement Ezoic Method: The prism is kept at the base of the object sight the telescope to the prism, and measure the slope distance ‘d’, now tilt the telescope up-to the tip of the object. The height of the object is displayed, from the bottom of the prism depending upon the instrument. This feature measures the elevation of a point where a prism can not be placed directly. The measurement is extended along the plumb line while the elevation is continuously displayed.

Ok I will try.

@@BakhtiKhan-us6xg Thanks

@@majidkhanraja4682 جناب ہے کیوں نہیں بس نام مختلف ہے فنکشن کا

@@majidkhanraja4682 جناب Reference Line کے نام سے فنکشن ہے اس کے اوپر پوری تفصیل سے وڈیو موجود ہے چینل پہ چیک کر لیں

@@mdkhalidhossain2312 thanks very much

@@ZeeshanAhmad-rx4kz Thanks

Thanks very much

Right but Offset ko aik dafa check kr Len k zero hi Hy ya Kuch aur

@@imtiazbhao2133 بالکل لیکن کنفرم کر لیں کہ آپ کا offset پہلے سے ہی زیرو ہے یا نہیں ۔ مطلب offset زیرو ہونا چاہیے چاہیے پہلے سے ہی موجود ہو یا دوبارہ لکھنا پڑے ۔

Thanks for appreciation

جناب اس پہ پوری پوری تفصیل کے ساتھ وڈیوز موجود ہیں چینل پہ وہاں چیک کر لیں

@@SurveyMentorWaqas oj

Thanks for supporting me

@@apurbamura8305 وڈیو موجود ہے چینل پہ چیک کر لیں

Zero Zero

Depends

@@Naveed89-gy4qm Thanks very much

@@AllInoNe-ff9uk thanks

Welcome

انشاء اللّٰہ