actually DIESEL is working far far better than motul or other chain cleaner, i already tested both, and getting best result from DIESEL only. Diesel can give longer chain life 40,000 to 50,000 KM easily. So i am using Diesel as a chain cleaner for my all bikes.....

Good mera bi same bana h please is ki diagram bi bata dain

is it touchable current

Yay same asa bany tu theek hu ga phr pahle bhi aisa banaya tha to kharab tha Kisi video mein dekha tha to itni jyada registered chij aaya Hogi ismein to Nahin kharab Hogi yah wala theek banega

Can you please tell what are the protection of this multimeter

Is 20w40 oil recommend for Maruti 800 carbeurator model of 1997?

Oi qual a potência desse resistor

Thank you for english translaition 😊

How much was the price? You didn't mention

Price kitna ha

Great video thanks you. Would this work from a 12v source?

Please share its working

I am messaging you on Instagram but you are not replying 😢

I also made one but it is not working 😭 please help I used a 10 inches pipe which is 1.5 inches in diameter . 34 Guage copper wire for secondary coil and 20 guage wire for primary coil. A tip122 transistor and 47k ohm resistor I made more then 1000 turns in secondary coil and 4 turns of primary coil. I used four 3.7v rechargeable batteries. I made the exact circuit as yours But nothing happened inly my transistor is getting hotter ......😢

Excellent

Thanks very much for this. Greetings from Belgium !

Hey, would this work if my primary coil is 2.5mm diameter 5 turns and 0.5mm diameter 1000 turns?

Good sharing video. Thanks bro..👍❤️

Useful video. I recently worked on brake pads for my car. I didn't see how you are pushing the piston back to allow space for the new brake pads. I struggled a bit to push the piston and later came to know tools available for that. Secondly as pushing the piston to create space it is very important once the brake job is completely done and before driving the car to do a brake pedal pumping. Pumping brake pedal will allow the piston closer to the brake pads then the car is ready to drive. It is very risky to drive car without pumping the brake pedal.

Can i ue l208n smd ?

Are you Indian ???

Super👌😅

Very nice work. Can it be programmed to display SpO2 two or more digits after the decimal e.g. 96.55 and similarly for the heart rate. Thanks

I bought every thing and arranged it as you said in the video, but it didn't work

Bro are suzuki swift rotor and suzuki dzire rotor interchangeable or compatible?

What is the brown board you used

Great video. Just made it and it works! of course it works. Just a reminder to anyone, putting transistors in parallel may not work, it certainly wont work for long or wont work period. This is because no two transistors are identicle, so the one with the least resistance will take up most of the work if not all of the work. So it makes very minimal difference. But this circuit certainly does work and you can try it with more powerful transistors to increase the power! Side note, Do not put a heatsink on the TIP31C transistor, It is electrically connected to the positive and will short circuit and kill the transistor: Learnt that the hard way :D

Bro i watched many video but your video was best i made this tesla coil for science day thanks for your help

Nice

lol, ...but, yor old cable didn't look like there was any damage on it... what was the problem with it?...lol

Nice demonstration and review.Thanks

bro idinu engine flush chyune nallathale??aenda abiprayam

You didn't lube the slider pins with grease..important maintenance item when replacing pads!

Well explained ❤

Thank you for this amazing Video. Which sensor did you use for water level measurement?

Mene iske output pr l293d ic and transistor dono use karke dekha but speed slow h lekin motor ko direct 5v ya 3v current dete h to motor ki speed jayada hoti h. Kya aap bta skte ho ise kese solve kre ?????

Sir can i use it without motor driver board

Iphone ?

Nice

Nice

𝘙𝘦𝘢𝘭𝘭𝘺 𝘐𝘯𝘧𝘰𝘳𝘮𝘢𝘵𝘪𝘷𝘦..👍

wow thanks for the torq values mentioned.. but curiosity to know what be the torque value for the caliper bracket carrier screws?

Really work aaguma please

I bought the components and arranged them as you showed. I now have the basis for a dipper tape for water wells. Thanks heaps

nice job - great video

Don't forget the warning sign on the back of the car that tell other drivers you have working brakes

Battery ko reacharge kese karenge nodemcu se kar skte hai kya

i cant use this app

this app not working

Fog lamp covern ethra aan