Self Skill

Пікірлер

@carlosconde4096 6 ай бұрын

How many meters of. 8mm wire for 1.5 mh and 2.7 mh coil. Thanks

@carlosconde4096 6 ай бұрын

What are the values or inductance of the coils?

@carlosconde4096 6 ай бұрын

The circuit diagram is well designed. Please tell the values of L1 L2 L3 L4. Thank you

@carlosconde4096 6 ай бұрын

Is the core shown iron?

@SelfSkill-fh4ok 6 ай бұрын

No. This is air core

@carlosconde4096 7 ай бұрын

Can you teach how to wind 2.7 mh coil

@SelfSkill-fh4ok 7 ай бұрын

If you use the same core as you saw in the video and the same 0.8 wire, it is enough to wrap it 19 turn until it is 2.7

@carlosconde4096 6 ай бұрын

How many meters of. 8 mm wire do i need

@SelfSkill-fh4ok 6 ай бұрын

@@carlosconde4096 A lot is written in the video

@thuthuu9897 7 ай бұрын

Can i use. tda2030?

@SelfSkill-fh4ok 7 ай бұрын

This circuit is designed only for TDA2050. It does not work with TDA2030

@SelfSkill-fh4ok 7 ай бұрын

TDA2050 has more power. I recommend you to use the original TDA2050 and enjoy the quality of this amplifier.

@poor708 8 ай бұрын

@parisrealife 8 ай бұрын

merci pour la video :) une petite question sur les watts que j'ai du mal comprendre. lorsque qu" un fabriquant d'enceinte autonome annonce une puissance de 300 wats es ce vraiment 300wats ???car ici je vois 45wats qui me semble tres !!! cela est il dur de fabriquer un ampli maison de 300wats?

@SelfSkill-fh4ok 8 ай бұрын

thanks for your attention. In this amplifier, an IC is used, which is designed for 4 outputs with a power of 45 watts and an impedance of 4 ohms. It requires 12 to 24 volts of electricity. Of course, the higher the voltage, the stronger the output power. Regarding the 300W amplifier, I can say that it is not difficult, but the type of amplifier and its voltage are important. I will try to make a video about a suitable circuit with this power in the future. 👍

@puiaturuburu906 9 ай бұрын

Good job

@40fps_gaming_pratham 9 ай бұрын

If you connect only capacitor in series it's blocks low frequency and it's gives a way to high-frequency

@SelfSkill-fh4ok 9 ай бұрын

Of course, this only affects the good tweeter, but it is better for midrange to have good quality.👍

@عبدالملك-علي 9 ай бұрын

فكرة مميزة

@PJkabahogbogan 9 ай бұрын

Amazing What power you use

@SelfSkill-fh4ok 9 ай бұрын

This circuit working by 12v or 14v DC

@danielalvarez3807 9 ай бұрын

Por qué cuando hacen esos crossover nunca lo ponen en una caja a los parlantes como corresponde.?

@SelfSkill-fh4ok 9 ай бұрын

Of course, to have a good sound from the speakers, be sure to put them in a suitable box. This video is just a tutorial on how to make a 3way crossover and at the end we will take a simple test of its output. Of course, I made another video where I installed the same crossover in a speaker and I recommend that you watch that video as well. I put the link here for you. kzbin.info/www/bejne/jIbUhYt8btqDp7M

@fernandozea6429 10 ай бұрын

Excellent tutorial, one question: Can this circuit be used for a 12" speaker, a 4" speaker and a 2" tweeter? The question is the values of the coils and their impedance. greetings.

@SelfSkill-fh4ok 10 ай бұрын

Thank you for your support. You saw in the video that I tried on woofer 12", midrange 6.5"and tweeter 3"and a total power of 200 watts. Of course, I had these speakers at the moment. But this circuit is set to 4 ohms impedance and it will definitely have a good performance in your desired system.

@SelfSkill-fh4ok 9 ай бұрын

Hi dear friend. You asked about the 150 watt circuit and I gave the wrong answer. I apologize for this. I made a video about the 300 watt crossover circuit. I recommend that you watch the video that is better for the speakers you want.

@SelfSkill-fh4ok 9 ай бұрын

I left the video link for you👇

@SelfSkill-fh4ok 9 ай бұрын

kzbin.info/www/bejne/hX_aaKB-ebOdnNEsi=oKuxpO4w_lZTvtxo

@waledabu365 10 ай бұрын

good day boss question boss .... can you please make a video for 1000w cross over network.. for tutorial.. thanks and more power.

@SelfSkill-fh4ok 10 ай бұрын

Calculate the output of your home speaker in terms of RMS. The same crossover can be used in most of them. For example, 1000 watts is approximately 250 RMS.

@puiaturuburu906 10 ай бұрын

Circuit diagram?

@SelfSkill-fh4ok 10 ай бұрын

I posted it on Instagram for you👍

@SelfSkill-fh4ok 10 ай бұрын

instagram.com/p/C3x88xhyua9/?igsh=MzRlODBiNWFlZA==

@puiaturuburu906 10 ай бұрын

@@SelfSkill-fh4ok wow thanks a lot. I'll follow you 👍

@ВикторЕршов-ъ7ь 10 ай бұрын

такую плату можно было реза ком прорезать

@SelfSkill-fh4ok 10 ай бұрын

Yes, I also cut it to the desired size

@baharehyousefi2188 10 ай бұрын

به به عاااالی 👍🏼

@فریده-ف1ح 10 ай бұрын

عالی .خسته نباشی.👍

@AdityaKumar-em7yv 10 ай бұрын

❤❤❤❤

@jaysonzabala7422 10 ай бұрын

Basag ang tunog. Kahit naka airphonena ako

@SelfSkill-fh4ok 10 ай бұрын

I also recorded the video with a mobile phone and unfortunately, the bass sound in the microphone of mobile phones is a little bad. Thankful. Your opinion is valuable for us

@lelordmarkquillopo6481 11 ай бұрын

how many watts can it handle sir? I also want to build one

@SelfSkill-fh4ok 11 ай бұрын

It can support up to 150 watts. If the tweeter sound frequency is too high, you can replace the capacitor 2.2uf instead of 0.47uf. You can also add 4 meters of wire with the same diameter for the woofer coil to make it bass sound better.

@rama1612 5 ай бұрын

@@SelfSkill-fh4ok orsir coper wire kitne gauge ka lena hien 22 ka enough hien kya?

@SamiraMohammadi-pf7bw 11 ай бұрын

❤

@SamiraMohammadi-pf7bw 11 ай бұрын

❤

@SamiraMohammadi-pf7bw 11 ай бұрын

Bravo

@الهامبیات-ي7ش 11 ай бұрын

wow

@الهامبیات-ي7ش 11 ай бұрын

Beautiful

@samiramohammadi1809 11 ай бұрын

Your efforts are commendable

@samiramohammadi1809 11 ай бұрын

Your hands do magic

@samiramohammadi1809 11 ай бұрын

Beautiful

@SamiraMohammadi-q5o 11 ай бұрын

Perfect

@SamiraMohammadi-q5o 11 ай бұрын

Wow