PaulZ RC

Пікірлер

@DUCDuc-lx3ks 4 ай бұрын

Paul did u finish n fly?. Cant find a next video

@pzukowski1001 4 ай бұрын

@@DUCDuc-lx3ks not yet, busy summer this year.

@ActionRC-Russ 4 ай бұрын

Great video with great information about your jet, keep.it up , Russ from Action RC

@eladyeffet 4 ай бұрын

A very well made and a very nice video! Just a small correction, when you deploy flaps the C.G doesn't go anywhere, if you didn't move anything in the plane the C.G will always stay at the same place it was before. What actually shifts is: the center of pressure- and since it changes the arm between C.G and C.L (center of lift AKA center of pressure) you get either a nose up or down tendency -depends of the design of the airplane (In some airplanes you don't get neither, and that's because in that particular airframe- deploying or retracting flaps does not affect C.L) Thanks for the video!

@RCPlaneReviewer 4 ай бұрын

Glad to see im not the only one thinkng the t45 comes in a lil quick! My HSD doesnt like to slow down.

@Mrtcoltpilot56 4 ай бұрын

Waiting to maiden mine. I also installed the Swiwin 80 on mine with a Smooth Flite 16. I'm using flight mode for flap to elevator trim mix. I have the orange and white Navy version. Nice flight.

@51PMustang 4 ай бұрын

Hi Paul, Awesome video. I have 2 questions: Where is your CG? Can you please confirm that you had to trim nose up with full flaps deployed? Thanks for taking your time.

@pzukowski1001 4 ай бұрын

CG at 188mm, yes nose up trim for half and full flaps.

@StevenGalea-wf5ml 5 ай бұрын

HI Paul. I have a question for you about the T-45. Do you have an email address that I could contact you at?

@jimbell2236 5 ай бұрын

Thank you. I’m thinking of get a HSD EDF so this is helpful

@nijhofrichard 6 ай бұрын

Very nice👌👌

@kaisellmann7675 6 ай бұрын

Nice flight! Can you tell me the weight of your L-39 and what kind of EDF you fly? Mine did not take off with a 110 EDF from Schübeler. I guess it was too heavy. Regards, Kai

@pzukowski1001 6 ай бұрын

Hi, I use the HSD 105mm EDF. I am surprised you had problems getting off the ground with Schubeler. You may have the CG too far to the front - that could prevent rotation. I have not weighed it in a while but it is otherwise stock and it flies with two 6000 6s batteries.

@kaisellmann7675 6 ай бұрын

@@pzukowski1001 Hi, ok, thanks for the answer. Yes, I am surprised too :-) I tried with two 6S 7000mAh, but had additional 3x 2S 5000mAh for the PowerBox Competition SR2 and the light. I will try again or get rid of two of the 5000er Lipos.

@51PMustang 6 ай бұрын

Hi Paul, Do you have to mix elevator with full flaps? Do you have to mix up or down elevator with full flaps? Thanks, Stefan

@pzukowski1001 6 ай бұрын

Hi, yes I have a little bit of up elevator mixed with the flaps. The plane noses down with flaps deployed so you need to compensate for that or it will come in fast on final approach.

@kennypowers1860 6 ай бұрын

The gear looks better than what came with smaller L39/Viper 2000mm and H9 MMB, I realise they are the bigger size (150 over 120) but also the retracts look far more like JP quality

@LOSCABOSLIFE 6 ай бұрын

Thanks Paul, looks amazing. Will be following your build and maiden. Cheers.

@garys3418 6 ай бұрын

Paul looking forward to flying with this and my F15

@victorrcjets7660 6 ай бұрын

It does look good 👍 seen the Black horse viper fly with no issues.

@FlyWithFrank 6 ай бұрын

Thank you Paul for putting this up.I'm sold. I want one!

@John-n7q9z 6 ай бұрын

Keep coming out with more good videos

@StyleWarZ1 6 ай бұрын

Question. Is the Firmware on the MFC and the Spectrum reciever updated to the latest Version?

@pzukowski1001 6 ай бұрын

On the Spektrum RX yes. On the MFC I have no way to know. It is version 1.1. HSDJets does no publish their firmware roadmap so no way to know.

@StyleWarZ1 6 ай бұрын

To bad thats not the problem. Please update if something changes as I'm thinking of getting a HSD.

@pzukowski1001 6 ай бұрын

@@StyleWarZ1 the solution is to not use SRXL2 and just connect each channel individually. The MFC is an amazing box and works great. I use it in my non-HSD plains too.

@StyleWarZ1 6 ай бұрын

@@pzukowski1001 and gyro you take from the receiver or from the box?

@pzukowski1001 6 ай бұрын

@@StyleWarZ1 I use the gyro in the receiver or an external one. Have not used the gyro inside the MFC yet. Would like to hear from others that have set it up.

@sonnyle8831 7 ай бұрын

Can you let me know, or update us on if you were able to fix or find a solution to this?

@pzukowski1001 7 ай бұрын

Hi, there is no fix for the SRXL2 incompatibility right now. What I do is connect the RX to the MFC using the PWM ports, so one cable per channel. The MFC is such an amazing product I don't mind the extra cables for now.

@gareturban3558 7 ай бұрын

WTF

@hakameng6936 7 ай бұрын

How to take the correct dimensions, choose the correct weight and airfoil, conduct a stress analysis, and choose span and rips as well. Thank you To make a miniature model

@andrewmccleod7785 8 ай бұрын

Good afternoon first of all thanks for the vid video. It was very helpful but I have another question. Did you do the CG with the gear up or down?

@pzukowski1001 8 ай бұрын

Gear down. CG should be measured with the plane in landing configuration.

@jadamian75 8 ай бұрын

How many amps is your system pulling. Mine with the JP Hobby setup on the v2 PNP only pulls 99-103 amps when it should be closer to 130 amps. Not sure if changing to a JP 150amp esc over the Hobbywing Flyfun ESC will make a difference.

@matthewllewellyn5302 9 ай бұрын

Buy a jeti controller. You wont struggle a day longer

@matthewllewellyn5302 9 ай бұрын

Beautifully put together. Extremely neat.

@michaellussoro2295 9 ай бұрын

Can you explain how you installed retract controller? My brand new l-39 door sequencer fried. 3 servos during build process, I didn’t notice servos bec was at 7.4 volts I swapped to 6v and I can get servos to not fry now but wanting an all in one unit

@spanishcop2090 11 ай бұрын

Hello Paul.... Can you tell me what your elevator settings are set for your flaps? I was told it would need some up elevator to bring nose up during approach. Can you tell me your elevator settings for both take off flaps and landing flaps please.Thank you sir

@aint_no_saint8782 11 ай бұрын

Envious. Wish we could have a concrete runway!

@lwrandall 11 ай бұрын

Paul where did you get the Edf motor? Thank you

@pzukowski1001 11 ай бұрын

Hi I bought it at turbines-rc.com. They are located in France but shipping is quite reasonable. They carry all the JetFan EDFs.

@lwrandall 11 ай бұрын

@@pzukowski1001 Did the plane come with the shroud around the motor?

@pzukowski1001 11 ай бұрын

@@lwrandall not sure I understand. The plane did not come with the EDF. I bought the JetFan EDF with the HET motor as a set which has been balanced together.

@lwrandall 11 ай бұрын

@@pzukowski1001 sorry. I am referring to the bracket surrounding the front of the Edf. The shroud directs the incoming air into the Edf. You show it at 2:08 in your video. Thank you.

@brianvallie1371 11 ай бұрын

Good morning, I'm setting up an L-39 with a dx 20. What aircraft type did you use to get the rudder and nose gear to steer correctly. Can you share how you did your setup. Having issues figuring it out with the 2085 module.

@pzukowski1001 11 ай бұрын

Are you referring to aircraft type setting in the transmitter? That should be set to your wing configuration which for the L-39 is normal: 1-AIL 1-FLP 1-ELE 1-RUD. Are you using the MFC-2085-DR or an older 2085? The new DR has a separate nose-wheel servo port HS-06. It is already assigned to the rudder RX input and it follows that channel. You can reverse it and setup travel/subtrim independent of the RUD channel. The DR also has a nose wheel gyro you can turn on and it seems to work quite well to help tracking during takeoffs.

@johnmueller5482 Жыл бұрын

Hi Paul good video .Are there any new planes or videos .All the best

@johnmueller5482 Жыл бұрын

Thanks for the videos hope to see more videos

@johnmueller5482 Жыл бұрын

Have you been building any planes

@pzukowski1001 Жыл бұрын

Yes, currently working on a TopRC P-51 composite model. Will be electric powered

@mr.maneuver287 Жыл бұрын

What resisters you got to make this work can you provide a link

@pzukowski1001 Жыл бұрын

Hi, I don't have a link handy but 130ohm 0.25W is what I used. You can get these on Amazon

@mr.maneuver287 Жыл бұрын

@@pzukowski1001 thank you and exactly how did you applicate them and how many do I need

@pzukowski1001 Жыл бұрын

@@mr.maneuver287 You need one resistor per LED. They can be soldered anywhere in series with the LED.

@tyjeadonaldson1459 Жыл бұрын

was it hard to hook up the mfc controller? im a fan of them as well and i want to put one in my goshawk

@pzukowski1001 Жыл бұрын

It was very easy. I plugged in all the servos directly into the MFC. That's what it is designed to do.