Я использую инверторный сварочный аппарат на 200 ампер.

thanks bro

thanks for your attention

My friend, observe two points. First, know that the smaller the angle of the electrode with the work surface, the less likely it is to get punctured. For example, a 45-degree angle is less likely to cause a puncture than a 90-degree angle, and secondly, reduce the amperage a little. and quickly remove the electrode from the work surface

At least say thank you

thanks bro

thanks

My dear friend, our goal is education, there are situations where the rebar is inside the work or building, and we need to add a new rebar to the previous piece.

Well said better to know how and never need to than to need to and not know how

Thank you for your opinion, dear friend, for two reasons: firstly, the open tube causes the part to be exposed to air and decay factors from both the inside and the outside, and it doubles the possibility of damage, and secondly, it has a beautiful aspect, people do not like it. They see a wood with a hole and thirdly, in many cases we need the work to be closed to prevent the entry of wild animals

@@ok_welding Thanks that was enlightening

My dear friend, I announce the amp and specifications in all the videos

😂😂😂

Thanks 🔥

Sure, dear friend, I'm glad you were satisfied

Sahabatku, film ini tujuannya sama, mau bilang permukaan pipa galvanis harus digosok dulu.

E6013 2.6mm

درود بر شما همینجا سوالتون مطرح کنید من در خدمتتون هستم

@@ok_weldingموضوع ویدیوهای کانال من مشابه کانال شماست، آر‌ پی‌ ام این سبک از ویدیوها چقدره؟ به ازای هر یه کا بازدید چند دلار بهم میده یوتیوب؟! و اینکه ب تعداد تبلیغ های روی ویدیو، درامد هم به همان برابر بیشتر میشه یعنی اگه 3 تا تبلیغ بذارم، آر پی آم هم 3 برابر میشه؟

Hello, my dear friend, about 1 to 1.3 dollars

Obrigado, que bom que você ficou satisfeito

درود بر شما خودکار جالبی نبود بدرد فلز نمیخوره یک بار استفاده کردم چون نوکش روی فلز کشیده شد خراب شد ولی یه ماژیک هست اون یکم بهتره بگو ماژیک سفید میخام لوازم تحریری ها دارن اونم مشکلش اینه پهن خطوط رو رسم میکنه راستش تا الان چیز بدرد بخوری پیدا نکردم

Thanks

Very good

thanks bro

Hello dear friend, everything gets better with practice

@@victimovtalent6036 Do not use 6013 rod. Bevel the joints better. This guy didn't really weld very well at all. I believe his amperage is set to low. Use 6010 or 6011 for a root pass also if possible, and cap with 7018

Thank you for your comment, dear Howard

؟؟؟

Hello dear friend, how can you work with me?

thanks🌹🌹🌹

no idea, but who cares its interesting right?

Hello, dear teacher, I was lucky that my film was shown to a great person like you

@tperm8075 not interested

Thanks for watching!

🌹🌹🌹🌹

Terima kasih teman, saya senang Anda puas

🌹🌹🌹

Спасибо за ваше мнение, дорогой друг

Дорогой друг, вы очень ошибаетесь, каждая ситуация со сваркой требует особого типа сварки, а точечная сварка является лучшим типом для тонкого металла.

Thank you for your opinion

По пробуйте сварку методом с верху в низ без отрыва и силу тока поставьте 95 или 100 ампер и вести дугу не снизу а сверху в низ и все у тебя получиться

درود بر شما دوست عزیز اول اینکه پیشنهاد من اینه از سیم جوش 2.5 استفاده کنی و امپر 90 به این صورت که نقطه نقطه جوش بدی نه یک سره اما اگر سیم جوش 3 بود امپر 100 و سریع و بصورت نقطه نقطه جوش بده که قوطی سوراخ نشه

ممنونم

Obrigado pela sua opinião, caro amigo, com certeza farei isso em breve