Can you show tilt and cenetring adjustment process of lens as you have disassemble the major parts of the lens I have the issues after the assemble of lens The image is not sharp

Where can I buy the tools that you used?

How did you install the crack guides in confuse there

where did you get your pins from?

Before you try all this, try taking the battery out, turning it off for a few minutes, and turning it on again... worked for me. But mine was a magic lantern-induced error.

how did you remove the front panel? it seems like you just grab some tape against it,much thanks if you could explain it

You show replacing a whole new section, including the new focus ring, because you used it from another lens, but all you need is just the focus ring, when you're replacing it with a new one, right? Is it pretty simple in how it comes out of and goes back into the housing that your replaced in full? Are the more screws or does it just snap in place? My copy doesn't AF at all. Putting my ear up to it, I don't hear it trying either. Does this mean it has to be the motor, or could it be something else wrong? Looks like the AF motor rings are under $75 on ebay. Pretty worthwhile to have AF working again.

👍👍👍👍

whats a repair cost for this ?

have same issue with my 5div but i have not enough balls to do it 🙄

In my Lumix GH5s the dial on/off us broken, (the plastic ring unde the diak that stop it) i appreciate info about how to remove the dial 🙏

why couldn't you show how the battery retainer lever spring goes into place?????

Great presentation. Wondeing if you have any experience with DA 35mm f/2,8 Macro Limited - I have one with some dust inside back lens (bagnet side). Need to find someone who can clean it or...do it myself..

Hello, i have a Tamron 24-70mm f2.8 canon G1, and i have a issue when i record video. The images " jumps" sometimes and I can hear the sound of aperture even though I don't change it, and also subjects appear with some red marks around them, like I'm manually focusing. This is what happens when the image jumps. Plus the recording sometimes stops when the images jumps. . What could be the problem? 🥺🤔

z6 shutter cost

My lens works fine on DSLR but when attached to adaptor to use with mirrorless Canon EOS R, the autofocus stopped working. Is this the same problem? Or sth else? Thank you in advance.

I was happy too soon. At 12 mm, err 01 came before. But the cable had not broken apart. After the repair the lens went back to 12 -24 mm wide angle. I was happy. Then I set the aperture above 4, and the error was still there. Nevertheless, thanks for the tried help with the video. Wolfe

Thank you for your clear video. Where can I order a new shutter?

Thinking about picking one up for cheap with this same problem. Do you need anything to readhere the rubber grip?

If i Use cfExpress could this problem be solved?

I have a Tamron 70 - 210 f/4 VC and it takes a long time to lock focus. why is that sir? I haven't used my lens for a long time. please help. Thank You

Thank you very much, I have this same problem

How did you remove the external body at 4:15 ? Thanks for the vid!

omg thank you so much !!!

OMG!!! You show how to remove the rear lens group! That's exactly what I needed! Thank you!

Professional job. My lens has same problem. It was serviced by Nikon authorised service centre twice but again the blades have become sticky. I can't spend more money on it. Will have to buy a new one.

Hello! I am about to start this repair tomorrow. Wouldn't removing the dew sensor fix this issue as well? Or would soldering two wires on the sensor fix it too? They don't sell the sensor anymore so I'm looking for ways to bypass it. Thank you!

How does it cost to change sd card slot?

Ein selten dämlich und unnützes Video! Statt der grausamen Musik wären Infos so viel sinnvoller gewesen! 👎

how much does it cost to repair defective VC on 150-600 g2?

thankbyou so much for showing this. I was able to replace the roller on my gx9 as well!! But I have a new issue, after I put everything together the flash don't fire anymore. Camera system recognizes when the flash is up or down, but it is not triggering the firing. I connected everything as it was supposed to be... what do you think is the cause of this issue? Thank s a lot again

VENDEN SENSORES PARA BLACK MAGIC 6G E7D5A4D4 PARA LIMA PERU , PPORFAVOR ESTARE AGRADECIDO,Blackmagic Pocket Cinema Camera 6K G2 , FABRICANTE : Blackmagic Design Inc , VERSION DE FIRMAWARE : 7.9 , NUMERO DE SERIE : E7D5A4D4 , Hola mi estimado Cómo estás Que tengas un buen día Saludos desde Lima Perú Mi nombre es José Penachi y tengo una Black Magic G2 el sensor de mi black muerta o sea ya no funciona porque lo cayó láser hay alguna reparación? HAY cambio de sensor se puede hacer algo o sea todo funciona toda la cámara normal hace todo su función la única es que el sensor está dañado o sea no hay imagen no hay nada Cómo me puedo poner en contacto contigo Espero tu mensaje muchas gracias

Excelente trabajo.

My canon r viewfinder glass is broken please help me know how to replace it through your videos 🙏 2

What its cost?

clean that guy with your manual - thanks)

i fixed the VR , but i lost autofus, now it just hunts back and forth, do you have a video on how to fix autofocus? thanks.

I threw up watching this.

What screws are these exactly? Are these the screws that hold the sensor? who have their backs to the sensor? There are only three? Do you have to count the number of turns by aiming them and not by unscrewing?

13:50 just to make sure that ribbon connector on the zoom rocker goes nowhere right?

At the 8 minute mark - did you tighten the screws to count where the focus adjustment is? Is this a liveable solution compared to gauging?

7:13 what is this screwdriver size? I cannot unlock this one :(

Hai sir

👏👏👏👏

Hello, what is the name of the small piece that comes out at minute 2:02 that connects the flexible mount to the plate? I have a 17-70 tamron and I broke that little piece, thanks

Hi. What tools do you use ? My lens has mold in the front part? Do you recomend cleaning that? And what liquid should I use for that. Thank you

Does this also provide access to replace the front filter ring? I broke mine and need to put on a new one.

It would be helpful if you could leave links to where you got that screw replacement. Thank you for the video though, this is very helpful.

Excellent video tutorials, a great help! Thankyou.

Excelente