Пікірлер
@felixperez5932 3 сағат бұрын
What about for the F3?
@TheS4t 3 күн бұрын
Per Sportsman 1000 S?
@gregbrooks3577 6 күн бұрын
The engine is in the back. How does that help heat dissipation?
@ericsautvs9124 4 күн бұрын
@@gregbrooks3577 This is mainly used to replace the damaged hood, this net mainly plays a decorative role.
@Tristen200 11 күн бұрын
i have 2015 and 2017 and they said right side
@xxDivixyxx 15 күн бұрын
Do we have to buy the black outer housing or we can use the original one ?
@ericsautvs9124 15 күн бұрын
@@xxDivixyxx You can use the original one.
@xxDivixyxx 15 күн бұрын
Does the original one fit on these headlights or we have to buy the covers too ? Thanks :)
@ohioladybug7390 16 күн бұрын
This video was not helpful. The camera work is terrible and the installer is going too fast.
@bryanfranson 21 күн бұрын
What are the foams that come with it for?
@ericsautvs9124 21 күн бұрын
@@bryanfranson Stick to the bottom or center to avoid vibration
@patrickoneill6821 26 күн бұрын
Your video is showing the pioneer 1000, not the 700. Ive got a 700 and its impossible to find a tablet mount
@robs9324 26 күн бұрын
Can you still install a passenger backrest with the tail bag off?
@ericsautvs9124 25 күн бұрын
@@robs9324 Sorry, it may not be possible to install the passenger backrest.
@123devinzz1 28 күн бұрын
you guys should make a version with a built in fan pulling cool air in from the outside at slower speeds. i feel like that would sell like crazy. especially to the guys like me with 2024+ xp1000s that are insanely hot inside
@1micYT Ай бұрын
Does this block winch location?
@ericsautvs9124 25 күн бұрын
@@1micYT Does not block winch location.
@1micYT 25 күн бұрын
@@ericsautvs9124 Thanks! I can’t seem to find a full front bumper of yours on Amazon for my 2022 Pro XP. Do you make one?
@ericsautvs9124 24 күн бұрын
@@1micYT We do not have a full front bumper at present, and we will feedback this information to our R & D department. Thank you!
@flashflashbang2102 Ай бұрын
The red lockdown clip will screw up loading heavy stuff that you have to slide into the tray. I do like the 2" extenders though, great idea.
@raulsegovia4420 Ай бұрын
What extra device do i need for turning signals?
@ericsautvs9124 Ай бұрын
You'll need a rocker switch, flash relay and wire harness.
@thelifeoffastony1157 Ай бұрын
Did you just mounted it upside?? Lo😂.
@rhertenstein Ай бұрын
If you buy these and they don't come on when plugged into the keyed power source, check the pos/neg wire locations in the 2 wire plug. I have a 2024 and found that the positive/negative wires were reversed compared to the factory plug. Grabbed a small pick and de-pinned the plug that came with the fang lights. Swapped placement of the wires and it worked like a charm. If you don't know how to de-pin wiring plugs, I recommend watching a video on it. Super simple once you know what you are looking for in the plug. Takes a little pressure in the right spot and the wires can be removed from the plug. They snap back into place when inserting them back in.
@josuegarcia8424 2 ай бұрын
I did all the same steps on the video but I can’t get the white light on
@ericsautvs9124 2 ай бұрын
Hello, if you purchased in our store, you can contact us through the platform after-sales service.
@tg9217 2 ай бұрын
I'm having a terrible time adjusting the height of my brake pedal with these installed. Do you just have to uninstall it to be able to change the pedal adjustment or am I missing something?
@ericsautvs9124 2 ай бұрын
Hello, this product is horizontally adjustable back and forth and foldable, but can not adjust the height.
@kidburnz4891 2 ай бұрын
I assume they’re pretty easy? The factory sent two to be installed at the dealer but the dealer received two left hand guards… so I am going to have to install the right one when it comes but have my bike delivered tomm. They said the brackets are on so I just have to screw the right one in Is it that easy?
@ericsautvs9124 2 ай бұрын
Yes, the installation is easy.
@treybailey6313 2 ай бұрын
What size drill bit did you use to make hole bigger?
@ericsautvs9124 2 ай бұрын
Hello, this product can be installed without drilling, using only the vehicle's original screws.
@HillaryMosier 2 ай бұрын
Did not go together as easy as this! The clamps were very hard to get the bolts in and some didnt meet the holes anywhere close. Had to drill new holes.
@sexybabyboy69 2 ай бұрын
But why not use the bus bar?
@TonyTheFlatlander 3 ай бұрын
Any eta when these will be available on Amazon? I need one for my X2 1000.
@ericsautvs9124 3 ай бұрын
We are currently out of stock, it will take several months for it to be available.
@user-pp7bl6fr2m 3 ай бұрын
I just received my windshield for my 2022 General XP, and same thing,, There's about a 1/4 - 1/2 inch gap on 1 side, after I connect the other. I can't get it to clamp down after several attempts.
@ericsautvs9124 3 ай бұрын
Please contact us via Amazon message, we need more information to help you.
@LucDuval-rj9mh 3 ай бұрын
do you have the instal video
@ericsautvs9124 3 ай бұрын
Hello, the installation of this headlight is very simple. Simply replace the original headlight, plug and play, without the need for wiring; The video of dismantling headlights can be searched for reference on KZbin or Amazon.
@jaredwernicke6723 3 ай бұрын
Can this be used with the hood scoop light as plug and play or does the power to the hood light need to be disconnected?
@ericsautvs9124 3 ай бұрын
Yes, they can be used with the hood scoop light as plug and play.
@anthonynicholson5725 3 ай бұрын
Can you get blinking functionality out of these with the xtc street legal kit?
@ericsautvs9124 3 ай бұрын
They can work with the xtc kit. You need to connect a 100 Ω resistor between the turn signal wire (brown wire) and the negative pole of the light (black wire).
@anthonynicholson5725 3 ай бұрын
@@ericsautvs9124 thank you for the reply. Hate to show my ignorance but I'm not quite following. Once the resistor is between the turn signal wire and the black wire, 1. What would you hook the xtc turn signal wire to? 2. Once the black wire is cut wouldn't the plug and play plug no longer be grounded?
@ericsautvs9124 3 ай бұрын
@@anthonynicholson5725 1. Connect the xtc turn signal wire to the turn signal wire of the light 2. Do not cut the black wire, just break the outer skin of the black wire and connect the resistors in parallel, then take insulation protection
@anthonynicholson5725 3 ай бұрын
@@ericsautvs9124 got cha. Last question. I know you said 100ohm but I see them in .5W, 25W, 50W.....what wattage rating do I need?
@ericsautvs9124 3 ай бұрын
@@anthonynicholson5725 You can also use a 50 ohm resistor. The rated power is 3W.
@anthonynicholson5725 3 ай бұрын
Do the replacement running lights/turn signals only work with the ryco kit? Id like to make them work with the xtc kit if possible. Thanks
@NC0880 3 ай бұрын
I need to see some reviews on these! I want to buy them so bad but I haven’t seen any reviews. I really want them too
@ericsautvs9124 3 ай бұрын
Hello, you can click this link to see the product information and reviews:www.amazon.com/dp/B0B6VT57XC
@RayRay0783 3 ай бұрын
Is the Can-am already pre-wired for the grill? Was it connected to a dud retainer?
@ericsautvs9124 3 ай бұрын
Yes,plug and play.
@brandonblankenbeckler9975 3 ай бұрын
How did these boxes sound with the sub in it
@ericsautvs9124 3 ай бұрын
Do not worry,it will not affect the sound quality of the speaker itself.
@Cronistadelpueblo 3 ай бұрын
Will it make the back light blink as well?
@ericsautvs9124 3 ай бұрын
The headlights are controlled separately,they will not make the back lights blink.
@HappyRZRrider 4 ай бұрын
Seperate switch, or is it on when the low beams are on, or only the high beams ??
@ericsautvs9124 4 ай бұрын
Yes, you can control it with a seperate switch, connect it to the low beam or high beam.
@sam_rules76 4 ай бұрын
Do you plan on offering a liner as well? A little more coverage up the sides would be perfect.
@ericsautvs9124 3 ай бұрын
We will feedback your suggestions to our R&D department.
@EluderRacing 4 ай бұрын
will these brackets work with a factory Honda roof?
@ericsautvs9124 4 ай бұрын
Maybe not.
@joecatalano166 4 ай бұрын
WTF is wrong with him?
@estebanariasknn5688 4 ай бұрын
Why didn't you let the central light work?
@anthonyaustin2306 4 ай бұрын
what does the blue harness connect to?
@ericsautvs9124 4 ай бұрын
Hello! The blue plug-in is connected to the harness plug-in under the dash (next to the steering wheel lever), thank you!
@DonsATVAdventures 4 ай бұрын
I need one of these windshields for my new 2024 yamaha yxz !
@ericsautvs9124 3 ай бұрын
You can buy it at this link：www.amazon.com/dp/B0CKN1L9RZ
@DonsATVAdventures 3 ай бұрын
@ericsautvs9124 already collaborated with another company actually for a windshield. Would of liked to have collaborated with sautvs though aswell .
@ericsautvs9124 3 ай бұрын
@@DonsATVAdventures Thank you for your support.Looking forward to the next opportunity to collaborate with you.🌹
@MrDrummerboi1995 4 ай бұрын
Mine won’t turn on at all
@ericsautvs9124 4 ай бұрын
Sorry to bring you a bad experience. Did you install it exactly according to the steps in the reference video? If yes, but this problem still occurs, please bring the order number and relevant pictures/videos to contact us at Amazon after-sales, and we will solve the problem for you.
@MrDrummerboi1995 4 ай бұрын
Yes exactly the same way
@ericsautvs9124 4 ай бұрын
@@MrDrummerboi1995 Excluding installation errors or other factors, if it is a product quality problem, you can contact us through Amazon message on your order page.
@rhertenstein Ай бұрын
If you are capable and still have them, check the pins in the harness from sautvs. Mine was reversed. I re-pinned it with the pos and neg in opposite spots to what they came and it worked like a charm.
@J_TRAIN 4 ай бұрын
Good video
@AshtonP1tts 4 ай бұрын
Need these for the g2l models
@strykerstruckgaming8007 4 ай бұрын
War really hoping it would be RGB on the front.
@AshtonP1tts 4 ай бұрын
Some led headlights for these would be awesome
@rouge-shotzzz7251 5 ай бұрын
Does the xp1000 sport already have the wiring
@ericsautvs9124 5 ай бұрын
Yes, it fits for 2024 Polaris RZR XP 1000 Sport.
@rickymartin1507 5 ай бұрын
How’s the output at night?
@ericsautvs9124 5 ай бұрын
Sorry we don't have pictures or videos of this, but the lumen of the headlights is around 2500.
@totalenergy80 5 ай бұрын
What bracket is been used on the shock tower light??
@ericsautvs9124 5 ай бұрын
Hello, the installation of this product does not require a bracket, please refer to the video for specific installation steps, thank you!
@middlehot 5 ай бұрын
In the instruction we dont need to remove everything just hood and grill for the front and bed for the back??
@ericsautvs9124 5 ай бұрын
Yes, no need to remove too many parts.
@middlehot 5 ай бұрын
Thanks
@firdous.bhatsonamarg7080 5 ай бұрын
Hi This is for sale
@earliebraggs2763 5 ай бұрын
Seems like you would remove the stock fender after putting on the extended one above it?
@ericsautvs9124 5 ай бұрын
We refer to the OEM design. If you are using the original lower fender, it will not affect the installation and use of this product, thank you!
@earliebraggs2763 5 ай бұрын
@@ericsautvs9124 Ok. Was curious! Thanks!