Can't wait for more Prelude components. Especially for the 4th gen chassis.

I wish I would’ve looked this up when I timed my car. Rebuilt ls bottom end and bought used vtec head. Didn’t know it was that easy

How did u flare the ends???!!

I'm currently having clearance issues with the front drop forks on a B18A1 swapped EF sedan. The flat side of the fork is rubbing against the axle boot. The forks are installed in the correct side and I didn't have this issue with the oem forks. What could be the issue?

Y’all inspiring me to take on my swap! 🔥🔥🔥 Keep up the content!

Damn, it's exactly the information I was looking for... the only difference is that I need to do it on my Nissan 240SX S13, do you know of any place where they sell the complete kit like this one from MPC MotorSport but for Nissan? This one from Honda, I'm not sure it's the same size as the connectors.

Mpc stuff looks really nice. Would definitely like to get a set of your drop forks for my bagged ek sedan.

Dam, I thought KZbin unsubed me from you channel it's been a hot min since you guys dropped a video.

wish i had yall for my swap, my shit is a mess 😔

Nice. Where are you located at? I want to get my 1993 Civic ex coupe swap to b20

Can you use the drop kit for stock suspension?

what rims are those?

Does it have a check light for ABS on dash?

Gonna install mine soon with some shorts and a vlog 👍🏼 wish me luck

whered yall go?!

Do you have to use a b series radiator? I feel like I’ve head you can use a d series before

Nice vid gents👍🏾

Can i use skunk lma on stock cams?

🤤

Very helpful video❤

Was wondering if don't have hardlines in the car anymore switches everything to braided brake lines what fitting do I need

You guys had the motor on the stand and didn't check the bearings ? Never trust buying a used B series .. most have been bounced off the rev limiter thousands of times lol

Nice one💯👍💪🤝

After watching this video at least 3 times, I just placed my order. For a simple and plain d16z6 rebuild on a car that's gonna get a clean subframe and engine bay, this just makes sense. I appreciate the brake line flaring tutorial as well. You made that not scary for the weekend warrior. Thanks again!

Super clean setup. You guys make these for EK/EM1??

Thanks guys !

Great video, really hoping you guys make a kit for the 4th gen Prelude!

Would y’all make a rear strut bar for the dc2 integras cause y’all front strut bar is nice

Music sucks every else great work

Hey what’s the link to those exact bolts that you used

O ok so you do have the vtec sandwich plate 👍🏻

I have the same build and I’m doing my lma tomorrow. Do you use a vtec sandwich plate with your build????

MPC all day 💯✊🏼✊🏼

This is officially my favorite channel now. I was looking into doing an entire restomod on my Teg and stumbled across your channel. I’m completely flustered at how quality your builds and hardware that you offer . Y’all will be the FIRST place I go to get all the things I need to refresh the bay. Thank you for making these videos and I hope y’all are well and still going strong

Is there anything special that you do to secure the passenger side brake line?

How did your get the timing belt off without removing the bottom cover? Mine is cut also

What did you do to hook up the evap system

Put a timing cover on. Sweet jeebus

I have a message and question in Instagram sir

I bought a JDM front GSR from someone and a week after I got it cylinder #1 piston cracked in half at the wrist pin, connecting rod cap came off and bent the rod throwing it through the windage tray. I'm spending what seems like a small fortune trying to get it back on the road. Funds are tight because I am on disability and have a 14 yr old daughter and a wife I'm raising, yes I'm trying to raise the wife too, lol.

Hey is this car still running the same stock ecu?

Luv the house music!

Do you guys know when these kits will be back in stock?

I messaged the Instagram profile, pleqse let me know !!!!

will this same kit work with the brake booster deleted ?

Looks clean! Great job

Lit

Excellent work 👍 nice Honda Civic 👍😎😎😎

Can not find a 40/40 for my life for under 100$ smh but as far as the parts list for the hardliners ,can I still use my old existing lines An reflare them or use the parts list Yal have listed ? I ask because I’m using a s2k mast Cylinder I’ also have in my Amazon cart lol 8 pack or steel tube nuts m10x1 in 3/16 size as well as 15ft of 3/16 brake lines just incase I can not use my oem existing lines If so ,will this be efficient an effective for my diy brake lines

do you guys know anyone in Cali or Los Angeles that does a great rebuilt of B18C1? Im an original owner of a 96 GSR sedan.