What code did you have , I have a p000b

Simple! My jeep has a hose that was ripped off from the purge valve. Just found out where it connects under the manifold. I'll likely have to replace the hose? But it is throwing a throttle body code now. I was told it could also be an alternator issue? But this doesn't seem all that difficult to do on my own.

I saw a video where someone had to solder the connection to the throttle body. How can I avoid that?

Good video, cool setup

Cannot get the break caliper back on …

I love you 😊

How do you know how many foot pounds you put on it? ( That music reminds me of my jam band show days ❤)

The sheet that comes with the wheel bearing assembly says to torque to 177 nm. That translates to 130 ft lbs.

What Is The Name Of The Little Rubber Piece I Told Them Grommet At Auto Zone They Couldn’t Find That

Awesome, thanks!

Good Video young man Thanks....

Can i take this christmas tree with a screwdriver?

18mm on back of the knuckle

Might be a dumb question but is there an easy way to know which one it is

Just replaced it… car still making same sound while trying to start… any tips?

Great video man, getting ready to do this on my 17 sierra! Great camera placement and awesome explanations of what you're doing. I'll come back to this for any refreshing I may need. Keep on keepin on and God Bless!!

Nice video thanks for sharing

That had to be the most strait forward video I’ve ever seen! Thank you!

Spot on. Thank you. Only difference for my 19 Legacy model was the 3, 15mm bolts holding the hub asm. They are 18mm, as you stated in the note I noticed after the fact lol. Thanks again!

Can you tell me where the Crankshaft positoning sensor is located plz

Thanks for the great video doing mines tmr!! This helps so much

The brake pad falling out had me crying 😂

This was the BEST how to video I've watched! Straight to the point and all information you stated was spot on! Thanks so much for this video!

Is the sensor built in on these models? I’m trying to find a replacement sensor for my throttle body and I CANNOT find it anywhere.

There’s a outdoor gear/camping store called Cal Ranch in my town that just opened. Think REI mixed with an army surplus store mixed with Ace Hardware. Anyway they have a huge Tekton selection which is awesome. They’ve been making more and more made in USA stuff which I always like. They’ve sort of replaced Craftsman and SK for me. Prices aren’t bad for most tools too.

Nice job on the video.. Nice Golden in the background

At 2:03 you mention a "christmas tree" is that the plastic fitting that attaches to the air hose you were removing? Also did you place it back on when you put the air hose back in or how was that handled?

I had 275115 before replacement

Thanks for adding the sizes as you go, now j can prep as I watch

Thank you, great video.👍

Dig the simplicity, and knowledge of the video. 🤙

This may sound stupid but I'm in the middle of changing one right now and I can't figure out how to get the clip off of the throttle body sensor so I can take out the throttle body is there a trick to this I got big hands I can't hardly see what I'm doing

Just replaced one on my daughters 2016 Patriot. Drained the ECM of residual power. Followed some steps and she seems to be fine. Great video. Appreciate your insight on this issue.

One of the best how to videos I’ve seen! This saves me a lot of time and mistakes. 👍

Very helpful

Next can you tackle oil cooler lines! Great video!

U didn't torque it ?

Is this the same with 4x4?

2017 patriot

Liked and subscribed! 2004 Liberty Renegade. Thanks

go to northern tools and buy the black vinyl matts and cut them to fit in the all the draws including top and the folding tray. best investment to upgrade the quality of this tool cart. the black foam pieces dont hold ur tools and moves around too much i can see that where u keep ur ratches and the one below that.

Thanks for a really clear video. I'd never done this job before and you made it very simple for me. Cool dog too!

Are you still selling those lights if so where can I purchase I have the same vehicle also what tires are those or rims?

2:50 my '17 Tahoe left front wheel bearing went out at 67k miles! having never done this before, should i change both sides?

Nice

What diameter drill bit?

Dammit if the drain and fill plugs on my ‘06 aren’t impossible to get off. Tried PB blaster, ended up stripping the hex. Tried heating with a torch and banging on it with a chisel. Won’t come off!!

thanks for this, i just bought this exact cart so this was helpful

That looks dirty probably first tcase fluid service