Thanks so much DTR, this is exactly what I was looking for. I want to avoid those "stainless" replacement flanges that rust out.

Nice thank you I had forgotten 😂😂😂

El filtro filtra el agua ?

What is the length of the stem? I have one like that, but an 8' stem is too small and a 10" stem iss too big. The house was built in the 1980's.

The filter isn't going to clen your tap water like a proper filter does though

I have yellow and blue......where can i put the blue one???????

Parabéns

Can't find the duct pipe. What does that mean

Oh 😳

One thing to add: you might need to cut the water line behind the fridge off before adding the filter. I did that and let the auto refill pitcher kick on to drain the excess water from pressure.

ty

What size is the L shaped thing you used?

2024 Austin Tx Called a plumbing company to see if they could stop my leaky shower head. Came over and quoted me $450+ to replace the valve cartridge. Went to Lowe’s bought the piece and installed it myself. Cost $60 and 45 min. In case someone was wondering if it’s worth it to try yourself. Thank you for the video!!

Out with the old and in with the old

Thanks help me a lot

This is my exact colors, so i will put blue in yellow as you say...question i live in miami florida no extra furnace down here for heat, should I leave the jumper on that is connected to R and RC if in miami...

I need a help,,, I have 3/4 main pex pipe and no flushing can be wrong at 3/4 pipe

Dont have remote 😢😢

You should NEVER do electrical wiring or installation yourself.

What are these types of toilets call, manual flush valve toilets?

Thank you

That's a big no no, screwing it on like that without using a wrench on the other side to hold the fitting. I see this all the time then they either bend the copper fitting on the other side or snap off the cpvc pipe ECT..

Think u saved my butt

Poorly engineered product, my Roomba floor vacuum has worked flawlessly for years, however this product always has issues.

It worked! I tried everything but twisting it. Thank you!

Ty it works

in the manual it says to shut off the water supply line first? how do I do this?

Great video. Thanks!

The first mistake is not taking a picture, second mistake is not remember how the cables go 🤦🏽‍♀️ 😭

😊

Fixed my issue.. Thanks!! PC Back running..

@carmedlitet2091 did you figure it out I’m having the same problem

Have that exact same thermostat 80s model sparks when AC kicks on

Thank you very much I’m just happy😃😃😃😃

Got it for $500+tax. Best thing I spent for the kitchen.

The jumper metal is in the way how do I remove it it won’t unscrew

The first time I did this I got water all over the place but this video saved my life second time around. Thank you sir 🫡

Hi if is still flashing blue on the back of subwoofer do you have any ideas?

Dumb question but does every AC machine unit have a filter that needs to be replaced? I thought only indoor units. Thanks

Thank you! This was exactly what I needed!

The grinding "metallic" noise isn't the same as the clutch assembly not fully engaging, as when you spun the unit by hand. Is there another part that could cause the noise, such as a worn bearing?

All you electricians obviously know he didn't install up to code, but instead of sitting here and critique him (btw, his replies are all professional). Just post the proper ways or just move on.

Wow! Thank you so much 🥰

Absolutely insane I was quoted $800 to do two of these inside my home by a local plumbing company, and that was with a discount.

What soundbar do you have??

omg

Thanks for the video. I myself wanted to diy and this is really helpful. I will use conduit wire as recommended in comments and improvise it but this really helped build the fundamental part of it. For those who are criticizing it, this is an informational video and there is always a room for improving, so whoever is planning to do it themself, they should not just watch the video and do it but rather do their own research and make the decision. Thanks and cheers!

Does the color matter red/black when connection them to the breaker? I have an old breaker that has some knob and tube plus some updated wiring and my hot water heater/ washer / dryer are on a Q0230 breaker. I noticed you have the red wire connected to the side the switch for the breaker. Is that for a reason or just where you put them?

Just wrong. You didn't use a torque screwdriver to torque to spec (torque, wiggle, torque, wiggle, torque) for the TWC wall plate or breaker (you barely tightened it), you didn't properly protect the wire insulation from being cut by the knockout hole in the breaker box (used totally wrong fitting, you used a romex fitting on the THHN wire in the TWC wall plate. Dangerous and you will be sleeping in this house while charging? Not me. If you change to romex then use the correct to clamp fittings and you must use romex 4 gauge (4/2 or 4/3 and use the third insulated wire for ground and cap bare ground). So much is wrong here yet you have the skills to do it right so just why or why! Remember this is a continuous load circuit and that can build up heat unlike just about everything else in your house so every step is important to prevent a fire which would give EV's a bad reputation. Please be safe and fix these issues.

How do you get the stored error codes?