Delete your channel

Damn what the hell is that a Chrysler K car carburetor now there's a nightmare

I'd like that the filter housing uses screws and not the stupid clips

Dude buy a drill extending a lot of Labor and a lot of time and if you're a commercial mechanic you know that you don't need to be taken the same numbers that says as the book that's an estimate like I said before if you're working smarter and not harder working 8 get in 12 done and getting paid for 14 those 30 seconds for each bolt turns into an hour what are you getting paid for that hour

Did your front end make thudding noise and had tire movement ?

It is very dangerous without any support engine on the bottom. The engine will be down. Safety first. I don't recommend this vedio.

Wow I always thought that we had to disassemble the sub frame, bring it to the floor completely, thanks from Venezuela

Really useful video but from 4:27 it now just shows your contact details and no video. Hmm

Where you get the injector puller

照著你的方式拆成功了

Top, do you have a video in which removing only the EGR Valve?

tHamks

Good work

how many miles/kilometers has the car ? when should we do that ?

Thank you.

Hola tengo el error 4F8E en un Bmw E60, ese metodo que realizaron lo soluciona?

Gracias, fácil de hacerlo en casa y te ahorras un billete

Do you use Honda bond?😊

If you don't film and show every step, you cannot give this video the title "How To Remove.." - Best title would be: "A Short Summary of Fuel Tank Removal on..."

DIY can't do this process then.

I had an oil leak from the oil filter housing, but replacing just the gasket didn't fix the leak. The seals inside the housing had failed, so I had to replace the housing. That fixed the leak.

About to do this work right now

Thanks, your really help me

請問 2002 E66 735Li 修鳥蓋漏油+汽門油封+頂筒 要花多少錢？

Hey thanks so much for making this video, I recently had to replace this on my car and this video is the only one on KZbin that shows the rear latch replacement in full with a good view of everything you have to do, you helped me so much! Thank you!! 👍👍👍

Excellent video!!! 👌👌👌

Hi there thisvonly change the gasket only or the whole set??

My 2023 rear main may be leaking. It's getting worse, but not enough to drip on the ground yet (plastic catches it for now) 18,000 miles

Excellent video, thank you!

這下面是什麼位置 洩水還是油

感恩謝謝

Dawng, I took of the two lines holding the condenser down on my E70 X5 35d and started to pry to separate the lines from the condenser, and the A/C gas blew in my face. Had freon all over me.

是皮帶過鬆嗎?

Thank you for your awesome video. It’s a huge help for us who needed to get this work done. Just a question, does the oil filter housing have rubber o rings inside that needs to be replaced?

🎉😢😂❤❤❤

OMG, yea!. I have a problem with fogging the windows inside when cold (when car park front of house). Trunk checked - no leaks. Is it possible that the heater is blowing humid air for some reason? Is it possible that there is moisture under the windshield? Nothing is wet. All windows are fogged up. Mazda 6GG 2007.

thank you

Excellent video thank you. No language necessary

Good trigger discipline with the impact gun when putting the wheels back on. Although personally i like to back the first lug nut out a turn and zip it back down to relieve any excess pressure. All in all, looks like a pretty straightforward job. The book time is somewhere around three hours, but id budget six if you're doing this without a lift or significant chassis work experience. All bets are off in case of "excessive" rust. The bolts holding the sway bar brackets look unfun to get a good grip on. Getting a blow torch in there? YIKES!

缸頭螺絲要換新的嗎？

He is not changing the head gasket. I certainly will not let them touch my car for changing head gasket.

Nic się nie stanie jak tak leje się płyn chłodniczy?

Excellent video. Exactly what I needed to watch to do this job on my C250. Amazing!!! Thank you much blessings.

Sir oil seal repair kar ne kitna cost padhega

👏👏👏👏👏

Service manual recommends to remove generator (alternator) before removing thermostat. Is is okay to skip this step as at the video?

Good job,but it is not finished after the torque (200Nm) you need to tighten the angle 90 or 180 degrees.(Depend from used bolt).

Been struggling with those damn screws for HOURS today on a 4G69....

ماهمش دوريجين السلعة تركية اخي

Thank you😊