Hola! Mensaje de error y el ventilador de refrigeración funciona continuamente.
@lynfordwalker117610 күн бұрын
Is this the Bluehdi engine?
@tamaspozer177210 күн бұрын
Hello, almost. Little bit other.
@fattarable17 күн бұрын
Peogeut 308 2013 automatgearbox not change vexel when it is not used a while, but after arount 20 minut working fine, what can the cause could be? low oil?
@tamaspozer177217 күн бұрын
It is possibility the oil level is too low. When you changed the transmission oil? Not to old? The oil filter clear? Please check it.
@fattarable16 күн бұрын
@@tamaspozer1772 A mecanik changed oil but I think they did not changed the filter and this week and it is the same as befor.
@tamaspozer177215 күн бұрын
@@fattarable I don't know exactly but I think don't have filter in the gear box. Usually there is a magnet in the gear box. This has to clean.
@sercan13917 күн бұрын
Teşekkürler. Krank devir sensörünün yerini gösteren videonuz var mı?
@tamaspozer177217 күн бұрын
Ne yazık ki henüz bununla ilgili bir şey yok.
@rafaelcampos515918 күн бұрын
Great work
@sercan13923 күн бұрын
Merhaba, size bir sorum olacak. 2. Viteste hızlanırken araba neden tekler? Sanki gazdan ayağımı kesmiş gibi hissediyorum. Nerelere bakmam gerekir. Sadece 2. Viteste yapiyor bu durumu.
@tamaspozer177223 күн бұрын
Merhaba. Öncelikle hatayı Diagbox ile okumayı deneyin. Hata mesajı yoksa başka bir viteste sarsılmıyorsa bir çeşit şanzıman arızası olabilir.
@sercan13923 күн бұрын
@@tamaspozer1772 diagboxta bir hata yok. Turbo arızası olabilir mi acaba ? Şanzımanda ise problem diğer vites geçişlerinde de problem olmaz mı?
@tamaspozer177222 күн бұрын
@@sercan139 Diagbox ile turbo tanılamayı çalıştırmayı deneyin. Turboyu emme tarafından görmek kolaydır. Şaftın sarkık olup olmadığını, ortamın ne kadar yağlı olduğunu kontrol edin. Her ne kadar turboda arıza varsa diğer viteslerde de ortaya çıktığını düşünüyorum. Aslında sorun, motor rölantide çalışıyorsa ortaya çıkar.
@sercan13922 күн бұрын
@@tamaspozer1772 rölantide dalgalanma yok. Enjeksiyonlara bakıldı herhangi bir sorun yok. Sanki arabanın yakıtı bitiyor iki üç saniyeliğine sonra hiç bir şey olmamış gibi gidiyor. Sadece 1. Ve 2. Viteslerde yapiyor bunu.
@tamaspozer177221 күн бұрын
@@sercan139 Ayrıca çevre koruma sistemine de bakardım: EGR valfı veya NOx sensörüne.
@steveofadown27 күн бұрын
Whereabouts on the vehicle is the tank located?
@tamaspozer177227 күн бұрын
The tank is under the vehicle near the left behind wheel.
@steveofadown27 күн бұрын
@@tamaspozer1772 back or front of car?
@tamaspozer177226 күн бұрын
@@steveofadown back of car.
@alexsyxov2232Ай бұрын
Спасибо за видео.😊
@salimmetinАй бұрын
Very good video, this could be one of the reasons of failure with adblue system.
@tamaspozer1772Ай бұрын
Thank you.
@salimmetinАй бұрын
@@tamaspozer1772 forcing the injector opening with the piller and steel brush, won't that damage the part?
@tamaspozer1772Ай бұрын
@@salimmetin I think the steel brush don't caused injury. The nozzle is inside the injector. I clean just cover of the injektor with brush.
@h3x.c0d3Ай бұрын
total crap. learn how to solder.
@gn.74182 ай бұрын
Why he do it? Which problem?
@tamaspozer17722 ай бұрын
This is preventive maintenance. You can see the too many insects can plug the radiators lamella. If the cooling bad then the air conditional works bad and the engine cooling will be wrong.
@Drag596Ай бұрын
Can this be blown away with air compressor and air gun from inside out?
@tamaspozer1772Ай бұрын
@@Drag596 It is possibility, but I think not the best way. The lamella thickness is very small. The too strong pressed air can be damage the lamella. The large dirt blown off can clog the rear cooler. So just carefully.
@sergser69822 ай бұрын
🤡
@Fluffums2 ай бұрын
Can you do this on T7 Peugeot 308?
@tamaspozer17722 ай бұрын
Sorry, I have just one car. There is Peugeot 308 T9.
@samirhani10002 ай бұрын
Comment changer le thermostat 308 1.6 2011
@the-muscle772 ай бұрын
And then after spraying that stuff what u do, run the engine or let that fluid boil inside of the filter?. Nonsent video
@tamaspozer17722 ай бұрын
Here I show you how can be clean the intake system with EGR. The blew out material stay in the pipe. The engine is cold, the fluid not will be boiled. One or two hour later start the engine. The first starting one little bit harder.
@alhama87602 ай бұрын
Ale partacz nawet nie wyczyscil obudowy
@tamaspozer17722 ай бұрын
Filtr ma za zadanie wychwytywać zanieczyszczenia. Zmieniam tylko filtr.
@alhama87602 ай бұрын
@@tamaspozer1772 i cały syf w obrębie filtrow znowu zostaję ja dziś wymieniłem oba i zobaczyłem po wyjęciu ile lisci brudu jest w tej dziurze po odkurzeniu klima zaczęła mocniej chłodzić szybszy nawiem się zrobił
@salimmetin2 ай бұрын
Well, be careful with the white hose of the fuel connector, you was struggling with the clamp, it can brake when you force to open it. You should gently pull up the middle tab and press the sides.. Check also this video with more details about the connectors at the fuel filter house : kzbin.info/www/bejne/gWfWlIiVj82Sb7c
@tamaspozer17722 ай бұрын
You're right. It is not easy disassembly this connection. I think it is not necessary disassembly the whole hose of filter.The lite "O" ring can be damage.
@sandrod.74973 ай бұрын
Se non la smonti fisicamente non risolvi nulla
@tamaspozer17723 ай бұрын
Questo è vero, ma lo smontaggio completo richiede diverse ore e non è semplice. Questa è una versione molto semplificata.
@gsg85963 ай бұрын
Nm?
@tamaspozer17723 ай бұрын
I don't used torque key. Approx 40 Nm.
@1986acko3 ай бұрын
I have the same problem with this error. Are this part is for the AC ventilator or for water cooling ventilator?
@tamaspozer17723 ай бұрын
This is for cooling ventilator. There is same, because behind the heat exchanger panel. First AC, then engine exchanger, next cooling fan.
@Nik-hm5um3 ай бұрын
Hi, in my car the injector adblue remains noisy and whistles when the engine is stopped in neutral also after clean it. Can cover the area with the injector holes with a sponge and clamp? if I put a band and close those holes, the injector is no longer noisy. In my car ADBLUE is disabled on OBD.
@tamaspozer17723 ай бұрын
I think your solution is not the best way. Try buying new injektor it is not expensive.
@Nik-hm5um3 ай бұрын
@@tamaspozer1772 Thanks for the answer...sorry I think that is useless expense since it no longer works. If the system ADBLUE is close from ECU , now the injector do not work anymore. Do you think it's dangerous to cover it with soundproof insulating tape? What function have those small holes mechanically?
@tamaspozer17723 ай бұрын
@@Nik-hm5um Hi, if the Adblue close in the ECU then the injector doesn't work. If the rewriting was good. Did be the SCR and DFP remove from the car? One may your car exhaust is clogged. Then the pressure come out from the injector. This is one hypotheses. Please look the exhaust pipe after the Oxidation catalyst.
@Nik-hm5um3 ай бұрын
@@tamaspozer1772There are DPF and all Adblue system... The ecu doesn't give me any errors and the car works like the 1.6 HDI euro 5 before the adblue system in the 1.6 BLUEHDI. Do I clean the pipe that you clean in this video at minute 2.54? Many thanks.
@tamaspozer17723 ай бұрын
@@Nik-hm5um Yes, without Adblue system the car is Euro5. I had Peugeot 207 car with Euro5. It don't has SCR and Additive DFP just muffler and pipe. The cleaning of DFP not easy this side. There are air defectors. See my other video: kzbin.info/www/bejne/j6PPXmqPfJ2flas.
@LungileEdwardMafele3 ай бұрын
❤
@Telstar_13 ай бұрын
Hello, can you share the link to the Peugeot parts finder diagrams, thanks.
@tamaspozer17723 ай бұрын
Hello here is the link: public.servicebox.peugeot.com/
@michamasnik98974 ай бұрын
Czy filtr DPF nie znajduje sie pod autem ? idą do niego metalowe przewody oraz wtryskiwacz Adblue . A to chyba jest katalizator ?
@tamaspozer17724 ай бұрын
Tak, jest to czyszczenie katalizatora utleniającego. Napisałem to również w komentarzu. :-)
@ИгорьОлейник-ш8ж4 ай бұрын
Спасибо за видео
@АнатолийЗалевский-т8й5 ай бұрын
Hello. Where are you from? I'm from Ukraine and I'm interested in watching your service. I have the same car and I take a lot of useful information from your videos. What did you change in this case? Or did you just lubricate the support bearing? And what language do you speak? Thanks for the information and video instructions. Good luck with the service.
@tamaspozer17725 ай бұрын
Hello. I'm from Hungary. In this video I grease the support bearing, checking the spring and other elements. I speak Hungarian (mother language), English and German. Thanks for your words.
@salimmetin5 ай бұрын
Is the oil fill location the same at 3008 1.6 bluehdi engine?
@tamaspozer17725 ай бұрын
I think yes, if it has manual transmission.
@ahmetemrecelik77575 ай бұрын
Kilometer ?
@tamaspozer17725 ай бұрын
Over 200 00 km.
@mehmeterhan42525 ай бұрын
Thank you for videos.
@Alex-Alex-20105 ай бұрын
Good job!
@darioh5535 ай бұрын
Thx for your video and for sharing your time in it. They are really useful
@ThePascal655 ай бұрын
J'ai la même panne actuellement
@tamaspozer17725 ай бұрын
Heureusement, c'est facile à résoudre.
@ThePascal655 ай бұрын
Je ne savais pas que c'était aussi facile .en tout cas merci pour votre aide au travers de votre vidéo ..ça évite de se faire voler dans les garages ......
@ThePascal655 ай бұрын
@@tamaspozer1772 j'ai fait la même chose que ta vidéo aujourd'hui .
@tamaspozer17725 ай бұрын
@@ThePascal65 Merci!
@Arkadiusz_Stec5 ай бұрын
o kórwa, niszczenie uszczelek szczotką drucianą gratis, a wtrysk jak był zajebany tak został brawo, dobrze ze nie mieszkam w pobliżu
@tamaspozer17725 ай бұрын
Próbowałem wielu rzeczy, ale nic nie usuwa przypalonego brudu. Jeśli masz lepszy pomysł, daj mi znać.
@Arkadiusz_Stec5 ай бұрын
@@tamaspozer1772 ja zdejmuję wtrysk, otwieram go i przepłukuję wodą i spręzonym powietrzem, tak samo zbiornik i przewody. wymieniam uszczelki, wtedy to ma sens, wtrysk zapycza się od środka ie od zewnątrz, to co ty robisz nie ma sensu, nawt jak pomoże to na chwilę, a rozwalona uszczelka ...
@tamaspozer17725 ай бұрын
@@Arkadiusz_Stec Dziękuję za odpowiedź. Wyjąłem też dyszę i mam filmik z tego. Czyszczenie sprężonym powietrzem ma sens tylko wtedy, gdy podłączysz napięcie do wtryskiwaczy i sprawisz, że przelot będzie drożny. Spalona na nim sadza nie schodzi wraz z wodą. Ja używam miękkiej szczotki drucianej, myślę, że się nadaje. Jak dotąd nie miałem żadnych komunikatów o błędach wtryskiwaczy. Mój sposób jest prosty i szybki do wykonania. W moim nie było uszczelki, gładka metalowa powierzchnia leży na górze.
@johneee99995 ай бұрын
Üdv Tamás, 1.6 blueHDI 85kw motornal (EURO V, nincs adblue), mi jelzi a regeneraciot? Esetleg valami tipp hogy tudnám figyelni? Előre is köszönöm
@tamaspozer17725 ай бұрын
Szia! Az Euro 5 motornál ahogy írtad nincs AdBlue. Itt csak a tankba adagolja az Eolyst tankoláskor. Így amikor a motor eléri a szükséges feltételeket automatikusan tisztítja a Partikulár filtert (FAP). Ezt csak akkor tudod nyomon követni, ha online figyeled a motor paramétereit valamilyen diagnosztikai eszközzel.
@NedumCosi5 ай бұрын
Thanks 👍🏿
@darioh5536 ай бұрын
Did you replace egr for cleaning anytime in T9 ?
@tamaspozer17726 ай бұрын
Sorry I didn't replace EGR for cleaning.
@Faisal_N226 ай бұрын
Any chance of showing how it looks under the EGR plastic cover? Mine is making noise
@tamaspozer17726 ай бұрын
I had once disassembly top of the cover of EGR. Some of the fixing tabs are broken. Under cover there is a electrical panel. I think it is not reparable. If you hear big noise you heve to change the EGR valve.
@Faisal_N226 ай бұрын
Thank you
@RC-ph7qs6 ай бұрын
Tamas, great work as always. How about a magic trick? My Peugeot 308 1.6 diesel from 2018 (T9), 88000kms on the clock, and the coolant level drops a bit every week when i use AC. If i just use ventilation, nothing changes. No puddles of colant under the car, no wierd smoke coming out the exhaust, no oil in the colant resevoir, no colant leaking anywere aroind the engine or into the footwell. WTF is happening here? Thanks for any tips.
@tamaspozer17726 ай бұрын
It is very interesting happening. Try use the car without under engine cover. Check the leakage.
@adithewolf21326 ай бұрын
This is not repair work is a bad cleaning proces is not indicate to do that
@tamaspozer17726 ай бұрын
Why do you think this? Do you have other idea?
@anesdj42826 ай бұрын
Have you tried the same with dpf?
@tamaspozer17726 ай бұрын
Yes, see my other video. kzbin.info/www/bejne/qWjWnICdrNaerpY
@Javi_Motilla6 ай бұрын
hello good. I have seen the video that you connect an LED to the heated rear window to see when the particle filter is regenerating and someone asks you why you don't connect it to the rearview mirror and you answer that removing the mirror is more difficult. Then it occurred to me, what if we connect the LED cables to the cable harness before the door pillar?
@tamaspozer17726 ай бұрын
Hello, You are right. It is mein opinion, that it is simple solution if the lamp connect to the back window heating. Try connect the regeneration LED to the mirror heating. And you can decide which is easier.
@FoxJohn6 ай бұрын
Mon dieu mon dieu ....des fois il y a sur YT de sacrés phénomènes.... Nettoyer un injecteur ADblue avec une brisse metallique et encore pire avec un tournevis 😮😮😮😮 franchement j'en ai vu des McGuyver du dimanche ; Mais toi tu as gagné le pompom ..une simple brosse a dent avec de l'eau chaude aurait pu faire l'affaire sans risquer de détériorer le joint ....et oui avec ta beosse métallique ru pourrais ue foutre en l'air ...et envore pire avec ton tournevis BREF de l'eau chaude et une brosse à dents aurait tout aussi bien fait l'affaire car l'adblue cristallisé se dissoud avec l'eau chaude ...la a mon avis t'as plus qu'a te racheter un nouvel injecteur 😅😅😅😂😂
@Javi_Motilla6 ай бұрын
Hello, thanks for the videos, I have seen several. I have this car and it leaks oil from the camshaft head, right where the diesel is spilling in this video. has it happened to you? Do you know any way to repair it without disassembling? all the best.
@tamaspozer17726 ай бұрын
Hello, I think you have injektor seal leak or camshaft head seal leak. It is typical Peugeot engine problem. This is impossible repair without disassembly. You have to change the wrong seal.
@Antsummerfield837 ай бұрын
What cleaning spray you use?
@tamaspozer17727 ай бұрын
I used EGR and Intake Valve cleaner.
@Antsummerfield837 ай бұрын
@@tamaspozer1772 thank you I will use the same 👍
@enriquemacchiavelli87717 ай бұрын
Very clear Thanks ! What is the name of the product/foam that you inject?
@tamaspozer17727 ай бұрын
I used Mannol 9694 DPF Foam Cleaner.
@GrooveMushroom7 ай бұрын
There should be a white led from the bottom. Is it possible to remove and clean it? Mine is all green from inside..
@tamaspozer17727 ай бұрын
Hello, I think it is not possible the White LED disassembly. It has a special glue. The whole side mirror disassembly is easy. Buy new one. I have one used light for sale. :-)
@GrooveMushroom7 ай бұрын
@@tamaspozer1772 where are tou from? I would love to buy it if it is clear)
@tamaspozer17727 ай бұрын
@@GrooveMushroomI'm from Hungary. There used white LED is good quality.
@GrooveMushroom7 ай бұрын
@@tamaspozer1772 Is is possible to change them? How much?))