If u need a gasket cut out a cereal box... they work and last...and by the way that threadlock is there for a reason...and i notice u did not check ur voltage...that is not a plug n play u need .96 to .98 volts on that style...

I'm happy to watch your channel. I subscribed too I have one without a turbo. Is the shock absorber the same as the turbo? 84-88 Thank you for your kind cooperation .

Did you put new pistons?

I just bought myself a 1990 f250 4x4 5.8 and I'm trying to fix all the things that are wrong with it,one question does the harmonic balancer pulley cause the engine to shake or there's something else doing it, checked the fan clutch and was fine. Do you got any other ideas

I used to block off sound resonators in the intake, with a decent drop in filter made a difference on many of my cars.

"Piece of ssshunk..." Lol you have more restraint then I do with cursing, you’re able to catch yourself haha

Had no idea i needed a special tool until i had it all apart.. on a sunday lol

Guy sounds just like jack nicholson

I subscribed I subscribed to your channel today. You seem like a good teacher who is thoughtful and caring.

Probably should've replaced the filter first. Now no matter what, you're just sucking hot air in

Doing same, im stuck on pulleys. Have the 87 style setup, but think the stock distributer is too big and cant seem to find a small thinner cap. What are your plans in terms of that?

Your car also likes cool air, not hot engine compartment air. Also, the KnN filter oil will contaminate your MAF sensor.

What about 1995 Ford 7.5 460 engines

I don’t like your attitude mister

Did anyone tell him about the size of the throttle body?

Do one with disconnected battery 😊

GO NAVY!!

Been following you since day 1 ! Any tips on who modifies z32 turbos ?

Any results?

I used to set the valve lash on my slant 6 with the engine running and a full face shield in case of spraying oil…. You wanted to feel the consistency as if you were pushing it through clay… if it pinched it was to tight if it slid right through it was to loose…. I might try it on this lol just crack the nut and set it while running… we shall see

What number is the clip couldn't see the number in the video

Wat in the fuck kind of driveshaft is that? is that a 2 piece ?

Wish we could see the partn#

I love your energy, and thanks for the helpful vid :). Hope you guys are doing well all these years later

I did like that. Thank u

Performer cam?

I can't see the number

I’m do it to my Cadillac ATS

This is a nightmare type of job. Once you go to moving all those old parts like the clips and rubbers start to break. You need to buy a throttle bottle gasket that you have to order because they no longer sell them in the store. Thanks for the video.

56 inch leafs are for 2500 trucks most commonly and 52 inch are half ton from my experience in doing a few of these lifts

Idiots design Ford engines

Can I use an external oil pump to feed my procharger

They say ford had a better ideal. WRONG

Thank you I have been dealing with this leak for months on my 2011 F150 Ecoboost - it started out very small and is now bad. This is a huge life savor and just saved me a ton of time and money!!!!

Worst cam installation I ever seen

Best way to start a video❤

What car was the first one?

I have a Ford Ranger 1993 V6 3.0 4x4. How do we check the codes?

Thank you for sharing this mod. I have the same renegade only it’s a limited. Same thing. I will be doing this soon. Just a heads up too, i think you may need to oil your k&n filter. Good job with mod and keep on wrenching

Appreciate you!!!

Retard

Ive been tinkering with classic engines for a bit and have wanted to dabble with turbos in more of a vintage vibe.... this is it. I think ive figure out how to run x4 strombergs and twin turbo a classic cadillac in an odd but fun way. Thanks for making this video, glad i found it... now down the rabbit hole i go

The driving gloves make it faster.

Thanks

Began using K&N products in all my vehicles in early 70,s. Never noticed any MPG increases. DID notice no more buying throw away paper filters and maybe a small amount of power increase on hill when in my Cummins engine. Gas engine ,just convenient and maybe psychological Minute improvement. Worth it ? To me yes.

..... Cars or engineered For Government pollution control and also intake noise You need more oxygen to get the miles per gallon up..😂😂😂

Can I use a N42 block from a NA 280zx instead ?

To maintain support, I left all of the pieces in place and perforated the filter housing with 2" holes from a hole saw. The opening total is 6 times the diameter of the plenum intake size. It works and it is stock stable................... ALSO, I fastened a piece of window screen around the housing to keep out bugs, leaves, and rodent parts!

Do you have to mess with getting or da Tory car set ups work ?

I have a 1994buick LeSabre on KZbin it said it takes a special scan tool because it was both OBD1 and OBD2 is this correct