Nice, you explained it very well. I never comment on videos, but this video specifies the process very well. Thanks.

If you're replacing all the wheel studs, do they need to be installed in a star pattern just like if you were tightening the lug nuts? I'm not sure if I did exactly a star pattern when replacing all my studs and now there's a gap halfway around between the rotor and hub...

What time of year do I make the cutting?

This was perfect for what I needed thankyou 😊

Thank you man . I need that tool now 😂

U need a sturdier bench

😯

thank you I was breaking my back and found your video very helpful

I wish I knew this before. I just used a stack of washers to pull the studs through with a T bar tire wrench. I still have an eighth of an inch to go on two studs and I've torn the threads out of three brand new lug nuts.

I've come to the conclusion that Nissan engineers are sadistic! The window motors seem to be designed so that grease flows out of the mechanism and into the motor, which destroys the brushes and armature. Just replace the brushes? Ha! good luck finding new ones. In general, they seem to delight in putting things in inaccessible locations and giving just not quite enough room for a socket or a wrench.

Hi.. what was the cause in your car why you replace this sensor?

Cool idea Chachi, but those are a little small for body armor.

Thanks Buddy

I just stumbled upon this and I think it’s great! I was looking to make ballistic panels for a backpack. I have 2 questions... What happens if the round hits in the middle of the tiles? And what kind of tiles again? I want to see if I can find a little bigger one. Thanks!

Great video thank you

Thank you for sharing your knowledge

is this guy melting lead inside??

What rounds does it stop?

Try fiberglass or Kevlar instead of denim

Flat footed?

I've just managed to find this video. Can anyone please tell me what kind of rating this armour plating would be? What I mean is......, what kind/type of ammo would this be rated against?

You’re a fuckin G

lol, floor has plenty of spill marks from past projects, but dont worry guys, hes wearing his special flipflops

Brass dosen’t RUST

Hi Sir, is it fine to cut the excess root coming out of the pot ?

Great video, especially the closeup, clear video of the cam sensor

You know you don't have to do all that. Just take the wheel off and pop out that rubber plug that covers the brake adjustment hole. Line the wheel up w the adjustment wheel and you can do it very easily.

Yummy

One of the best diy of had the chance to watch. GREAT JOB

How long takes to grow roots?

What would you do if the nut got stuck on the bolt with the installer… and the lug lost its threads so now it’s just spinning freeely 😢

How do you know that the stud is all the way in besides looking at it? I don't want to over tighten it. Edit: Can I use an impact instead of ratchet?

The only issue I have is the cracks between the tiles. A 556 bullet would easily go between that

Thank you! I'm going to do this myself today.

Best to add anti seize to prevent GALLING. Galling ruined two of my new studs and lug nuts😢😢😢

I think the more flexible alluminum was able to handle the rounds crushing the tile without being deformed. I think hard steel plates may be effected more early on as the bullet is penetrating before it actually hits the steel itself. I could totally be wrong though. Im no expert in balistics. One thing id probably do though to improve the design is use smaller tiles and more of of them. Im not sure if they are available or if they could be made DIY, but i would use four layers of smaller tiles four times thinner, and overlap them so that in between the tiles arent as much of a week spot. I think it could offer the same protection as your design, just without having week spots in between the tiles. I guess two large tiles that cover the whole plate could be used but then theres a chance that the entire plate gets cracked and compromized.

Thanks guy.

GIMME SOME I NEED ONE FOR MYSELF

Awesome Short & On Point! Greatly Aporeciate

I love mine. It's so easy to put on and fits perfectly with jeans or sweats

Gj

Thanks so much for posting this, never would have found it!!

No follow up?

Mine just blew out, waiting on new regulator, and watched this video to verify things that need to be done in a certain order. Thanks.

Oh please! Don't waste your money on this garbage. Just put a larger nut over the stud, then thread on your stud...it'll pull in the lug into position.

It doesn't work for me. It won't germinate the seeds. Even if I transplanted it to the egg carton after the seeds germinated it will die...

Question for people out there. What kinda native plants, herbs, flowers, ect, are from the Sonoran Desert region

I love you sir I'm burmese.

Thank you for your informative video. This helped me to replace the sensors. Only issue I have now is that it takes a few tries for it to start.

Instead of a pot, can it be just planted in the ground?