hello When the temperature sensor is connected to ESP 32 and I use it with a battery or a good mobile charger or an industrial switching source, the device works without problems, but after switching from a switching source in a place where single-phase and 3-phase electric motors work. They say that sensor information is not received. What do you think I should do?
@winson-DIY10 күн бұрын
Hi, Sorry About this issue , I don't have any idea !
@davidmike29897 күн бұрын
@@winson-DIY thanks
@thomassunkel922912 күн бұрын
Ein sehr schönes Beispiel, wie man Menschen irre machen kann. Es muss heissen: NEO_RGB (Red, Green, Blue).
@kimjongoof500025 күн бұрын
inputting the :P10,-10.0 code just make the serial monitor say ok>. The stepper is not moving nor drawing any current. What's the problem?
@winson-DIY10 күн бұрын
Hi, Can you check the driver board signal and power connected circuit !!
@sebassauva7006Ай бұрын
Hello, Does it work for CAN FD network? Thanks
@winson-DIY10 күн бұрын
Hi, Doesn't seem to work!
@domenicogaglianoАй бұрын
Does it work on a golf 7 that has gateway protection?
@winson-DIY10 күн бұрын
Hi, As long as there is a CAN message, it can operate !
@YTDans888Ай бұрын
How do I transfer the coding?
@winson-DIY10 күн бұрын
Hi, copy the code to your arduino IDE!!
@oscarlopez-lp7ls2 ай бұрын
Funciona para altsvoces de 6 ohms?
@winson-DIYАй бұрын
HI, Yes , It cam work at 6 ohms speaker.
@jorgehidalgo82432 ай бұрын
i did it ,but when i put la library into the gbrl file, the arduino ide send me another message to say me download another library
@winson-DIY2 ай бұрын
Hi, What is the message?
@jorgehidalgo82432 ай бұрын
@@winson-DIY c:\Users\Usuario\Documents\Arduino\libraries\FreeRTOS\src/FreeRTOSConfig.h:32:10: fatal error: avr/io.h: No such file or directory 32 | #include <avr/io.h> | ^~~~~~~~~~ compilation terminated. exit status 1 Compilation error: exit status 1
@YHdzz2 ай бұрын
Hi, the fact is that your indications or instructions on your blog are quite poor and unclear, which makes it difficult to understand; You should explain more that you need to use an Esp32SoftwareSerial library so that there is no problem with the code, you should modify your blog and be more explanatory with what you do because it is quite difficult to understand, on the other hand, how do I get the PC to recognize my code? ESP32 in CANHACKER software? I did the entire process, the wiring with respect to the diagram on your blog, I DID NOT HAVE ANY INCONVENIENCE WHEN COMPILED OR WHEN SELECTING THE ESP32 Dev Module BOARD in the Arduino IDE; What else should I do so that the CANHACKER software recognizes my ESP32?
@winson-DIY2 ай бұрын
Hi, Thanks your suggestion!
@HarishSr-r5p2 ай бұрын
Can i use mcp2515 to achieve duplex communication if yes can you guide me with some reference?
@winson-DIY2 ай бұрын
Hi, You can read and write in CAN Bus interface at same CAN config like CAN baudrate .. and Reference www.chosemaker.com/board/esp32/lesson-20/
@WoWPro712 ай бұрын
How do you power the module with 5v, when the 5v will set mcp gpios to 5v that can kill the esp32?
@winson-DIY2 ай бұрын
Hi, System power supply is 5V, that is not input 5v to GPIO pin!!
@kunal7biz2 ай бұрын
This is great.. keep posting.. I love this
@winson-DIY2 ай бұрын
thanks!
@kunal7biz2 ай бұрын
This is great.. keep posting... Thanks for the video
@winson-DIY2 ай бұрын
thanks!
@destrok35582 ай бұрын
And what happened to the other buttons? "Start - Select - Home - Address Pad"
@winson-DIY2 ай бұрын
Hi, there are not enough IO Pin to do that!
@miguelestrada53243 ай бұрын
what is the song of video?
@winson-DIY3 ай бұрын
Hi, this song is Coffee break!
@NisteCraft13 ай бұрын
Hey bro, I really liked this project of yours. Is there any way I can send the Can PID codes to the Serial Monitor?
@winson-DIY3 ай бұрын
Hi, Yes, but you need one CAN adapter via serial function !
@svsv93 ай бұрын
Thank you so much for sharing your project again. and bring so many aspect and details.
@winson-DIY3 ай бұрын
Thanks!
@svsv93 ай бұрын
@@winson-DIY Do yo consider use platform like Instructables or EasyEda commninity to get to more people. Well thank again.
@drstiven14663 ай бұрын
Hello, what library do you use for the mcp2515 and the esp32? I can't get both to work. Thanks for your videos.
the ESP32 code is placed on my blog : www-winson.blogspot.com/2023/08/esp32-obstacle-avoiding-robot-car.html
@LarryBrown-nq3mx3 ай бұрын
this is a shit video you do not describe how to do anythig
@svsv93 ай бұрын
Thank you for sharing this, I need 2 ESP32-Cam to control a toy(My surveillance car toy) I need 2 Cameras front and back, Can I add buttons to control motors and Pan tilt either to the Web page Server? I mean I need to control others parts of the MCU. Can you please clear me, Or Nod Red is only for streaming simultaneously?.
@winson-DIY3 ай бұрын
Hi, You can search esp_http_server for esp32cam car and I will make a video for this later!
@winson-DIY3 ай бұрын
Hi, You can see my github github.com/winsondiy/ESP32CAM_Car first and I will upload to my KZbin channel.
@svsv93 ай бұрын
@@winson-DIY this is amazing! Thank you so much for sharing. I will be at first row for this project of yours. Have a great day. I really need 2 cameras back and front just one working at time, only solution I can develop are with raspberry pi 5. If you can make it with two ESp32-cam it would be great. Thanks 🙏
@maryseglah52934 ай бұрын
wow amazing content, can I get your codes for the project
@winson-DIY4 ай бұрын
Hi, yes
@winson-DIY4 ай бұрын
Hi, Yes.
@VikasBabu_vicky4 ай бұрын
which app to use to control car?
@winson-DIY4 ай бұрын
Hi, No app application, that is Obstacle Avoiding Robot Car with HC-SR04 Ultrasonic Sensor!!
@jsiahaan4 ай бұрын
Hi! I 'm going to explore MESH in ESP32. Could you please give me a link of projects source code? Thank you so much!
@winson-DIY4 ай бұрын
Hi, I used painless mesh sample code to do it. and Put my project into my blog!
@pixellark31864 ай бұрын
Hello, I’m Mo I would like to buy this item. I have started to learn about CAN bus and I want to use it with my Mercedes Benz Actros truck, which operates at 24V. I want to sniff the signal of the start of the AC compressor, for example, and then simulate it on my workbench to test the compressor without having to reassemble it back in the truck. I don’t know id of it and how to decode it Can this device help me with that? Best Regards, Mo
@winson-DIY4 ай бұрын
Hi Mo, I'm not sure this device will fit your needs! You can buy ELM327 first and try it out.
@israaelmahdy91484 ай бұрын
are there any simulators I can try this project on?
@winson-DIY4 ай бұрын
Hi, You can try the Wokwi and search it from browser to understand it!
@israaelmahdy91484 ай бұрын
@@winson-DIY Thanks, I already did a search and didn't find the sound sensor on wokwi.
@winson-DIY4 ай бұрын
@@israaelmahdy9148 You can use a variable resistor instead of the sound sensor !!
My esp-32 does not working like that whenever i try the voltage drops like 4,50 4,60
@winson-DIY5 ай бұрын
Hi, What is your input voltage like? 9V or 3.7*2=7.4V?
@bennguyen13135 ай бұрын
Does the PCAN Basic API allow you to filter based on Node ID and/or Data? Ideally, setup a mailbox for each filter, then when a qualifying message arrives it overwrites the data in the mailbox.. this way, the cpu can either poll the mailbox and always get the latest value, or, get an interrupt and retrieve the mailbox contents!
@winson-DIY5 ай бұрын
Hi, Yes, You can filter your message what to you want by PCAN-Basic API. reference www.peak-system.com/PCAN-Basic.126.0.html
@insiyamurtaza58015 ай бұрын
hi, i tried all the commands in the rpi part and they are working fine, but how do i stream to my windows browser?
@winson-DIY5 ай бұрын
Hi, You can specify port to stream in the same domain!
@sosome15 ай бұрын
Which would you chose for realtime object detection: (Pi 5 with Coral USSB Acc ) or ( google coral dev board)?
@winson-DIY5 ай бұрын
Hi Pi 5 with Coral USSB Acc ! This group has better expansion!!
@officialrmb60885 ай бұрын
哈喽 请问怎么弄反馈声呀?
@winson-DIY5 ай бұрын
Hi 你所謂 "反馈声" 是甚麼?
@winson-DIY3 ай бұрын
When the Bluetooth connection does not play the audio and occur the squeaking sound.
@hosseinahmadi46225 ай бұрын
Very impressive work 👍🏻. I have Mks DLC32 board ready with TMC2209 drivers , is it possible to great the code and put it on sd card and print the sketch on my plotter offline ? Can you please help me with coding ? I am welling to pay for your help sir
@winson-DIY5 ай бұрын
Hi, Sorry ! I have no idea to do the function you want!
@SivaPrasadLibin5 ай бұрын
3:56 - 4:19 Your showing code contains lot of errors can you share the modified aurdino code 🤔
@winson-DIY5 ай бұрын
Hi, you can refer to this link www-winson.blogspot.com/2023/05/esp32-mcp2515-use-canhacker-on-can-bus.html
@heugor-india5 ай бұрын
@@winson-DIY Thanks for sharing I have now used the same code from your blog after uploading the program to ESP32 and I tried to connect with canhacker UI V2.00.01 now it throwing one error "CAN interface not responding!" any solution for this error? tryied Windows 7 and 10 same error
@winson-DIY5 ай бұрын
@@heugor-india hi! can you try this link www-winson.blogspot.com/2023/07/esp32-mcp2515-use-canhacker-on-can-bus.html for debug
@R2_Audio_5 ай бұрын
Nice! How is the sound quality?
@winson-DIY5 ай бұрын
Hi, The sound quality is pretty good but there is some noise during standby.
@louislule44589 күн бұрын
@@winson-DIYI did have the same issue, what I did was add in a mute code that is active when no audio is playing and inactive when audio is playing. This is designated to a gpio pin, any of your choice. Mine was D4, which I connect to the base of a tip41c transistor and then connected the collector and emitter to the 2 mute pins on my amplifier board. Don't put delay timing. This should fix the noise.
@alejandroperez53685 ай бұрын
How did you get the ESP32 to work with that MCP2515 module? You're powering it from 5V, so the communication between the controller and the microcontroller must be at 3.3V.
@winson-DIY5 ай бұрын
lingshunlab.com/book/arduino/arduino-use-mcp2515-canbus reference this link
@souhailbenbrahim1886 ай бұрын
how can we do the rest of the project on node-red
@winson-DIY6 ай бұрын
hi, Which part do you mean?
@jefflin13056 ай бұрын
模擬器可否提供訊號控制儀表板的時速轉速
@winson-DIY6 ай бұрын
Hi 這部分是可以的!
@jefflin13056 ай бұрын
請問如何判別出速度或轉速的ID ?
@winson-DIY6 ай бұрын
Hi reference this website en.wikipedia.org/wiki/OBD-II_PIDs
@jumboxgm91476 ай бұрын
Very good, you are a 10
@winson-DIY6 ай бұрын
thanks!
@maskusumaatmaja_3546 ай бұрын
good
@winson-DIY6 ай бұрын
Thanks
@MrFOX-ox4do6 ай бұрын
Good content friend, congratulations, sorry, could you help me with this error that I get? C:\Users\VIVE\Downloads\Grbl_Esp32-main\Grbl_Esp32\src\I2SOut.cpp:54:10: fatal error: FreeRTOS.h: No such file or directory #include <FreeRTOS.h> ^~~~~~~~~~~~ compilation terminated. exit status 1 Compilation error: FreeRTOS.h: No such file or directory
@winson-DIY6 ай бұрын
hi, github.com/bdring/Grbl_Esp32 try this link!
@MrFOX-ox4do5 ай бұрын
@@winson-DIY muchas gracias.
@emersonmedeirosnoberto80855 ай бұрын
Were you able to solve the FreeRTOS problem, friend? I've been trying to solve the problem for weeks.
@@emersonmedeirosnoberto8085 Recién pude leer tu comentario , disculpa, si subí el programa usando Visual code , y no me dio ningún problema
@Batara986 ай бұрын
please speel wiring mcp 2515 to atmega bro, thank
@winson-DIY6 ай бұрын
hi, I add a SPI pin define of mega2560 on the article on my blog! www-winson.blogspot.com/2023/06/arduino-mega2560-can-bus-radar-test.html
@nota10Xdev6 ай бұрын
You should add the commands in the description so it is easy for people to input them into their terminals. Not that big of an issue, just thought it would be nice for future viewers.
@winson-DIY6 ай бұрын
Thanks for your advice!
@brentmc796 ай бұрын
What is between the ELM327 and the OBD2 extension cable?
@winson-DIY6 ай бұрын
Use OBD2 extern cable to connect devices in CAN BUS
@cristhianmedina17047 ай бұрын
Do you have the diagram of conections?
@winson-DIY7 ай бұрын
Hi, DAC pins GPIO25 (Channel 1) and GPIO26 (Channel 2) connect to input of amplifier!!
@cristhianmedina17045 ай бұрын
Thanks you a lot for this video, and for show this library, at the end I created a project, that was an audio player in which I can control the player with a infrared sensor and control, make it pause, resume, advance and go backward (go to the previous song). Thank you a lot.@@winson-DIY
@winson-DIY5 ай бұрын
@@cristhianmedina1704 Good!!!
@TheJavaSync7 ай бұрын
Is it posible to use another esp32 to trigger button of 1st esp by esp now?