Hi, I have the same problem, were you able to solve it?

you need to set up de esc first

Bonjour, Merci beaucoup pour la vidéo. Quel logiciel en ligne utilisez-vous pour l'analyse et le calcul des volumes ?

i have the same problem. Can somebody fix it ?

the nano receiver is faulty and barely working in emergency mode.

Did you ever get this fix? If so how? Thanks

Had this problem on my radiolink byme-a gyro. Solved it by removing control surface limits (a.k.a. rates/dual rates) on my transmitter.

did you ever fix the issue?

I think something either wears down or burns out internally. I had similar problem with one micro tx. It would bind, but the crossfire lua wouldn't load or wouldn't show all of the data. I have tried with different open tx versions, eu or non eu, tried to downgrade to older crossfire software, checked Betaflight if everything is checked correctly but nothing has helped. If you have a possibility, try to put a tx from your friend and look if it helps. My friend's did work perfectly, so I have replaced mine as it was new at that time. Now, a few years later I am experiencing the same problem. I am waiting for my friends module to arrive again and I guess it will be the same story again, but this time my tx's warranty has expired, which will probably leave me either with trying to tear it up and look of any sign of wear/burn and try to fix it or buy a new one. I guess TBS hasn't the best QC. I had recently a Unify Pro 5g8 V3 go into smoke. It turned out - common issue - they have faulty regulators on them. After those unpleasent issues I had with TBS I am slowly looking to try Express LRS instead... Wish you all good luck with overcoming this problem!

Update: I tried connecting an external power source to the Micro Tx module before powering up my radio, and it worked.

Same problem here. I updated Tx module to latest FW, restored Rx to its "golden FW", updated remote to EdgeTx, too. After these, it successfully bound to the Rx again (updated automatically) then was able to use it for 2 days, then on the 3rd, got into failsafe while I was flying. Now I'm back to square 1.

Калибровка возможна на opentx(radioking rx18s) реверс газа не делаем,в пункте outputs 7ch ставим реверс,в пункте special functions Override CH3 вес -100(переключатель назначаем по вкусу например SF).Стики при калибровке газ влево-вниз,элерон вверх-вправо(mode2).может кому то поможет,неделю еб..ся.приемник radiolink R8FM,но думаю будет работать любым с ppm/sbus.

Do you think some plumbers putty might work around those clips ??

What worked for me: Disable "Internal RF" from your model settings also making sure the "External RF" is set to "CRSF". Only then will you be able to use your modules.

We have the same problem sir I got both byme A and D . I junk ha ha ha ha

Hi Stephan, how do I get the three position switch to 'talk' to the Byme-D on my TX16S?

Ahoj. Dávam odber. . .lebo mám problém s CRSF MTX2. :-D Pozerám, že nie som jediný. :-D

Same thing happens to me. I end up having to remove and reinsert the module a few times before it will recognize the module/connect to the receiver. I also turned off dynamic power and enabled multi-bind. That helped a bit, but the problem still comes back intermittently. I'm considering replacing the module. :(

Vraiment un beau projet 👍

I'm having the exact same problem on my tango 2 radio, Any help would be greatly appreciated

I HAVE THE SAME PROBLEM ANY FIX

I have the same issue with TBS tracer and Taranis qxt, new TBS firmware update didn't help and I am on the newest open tx firmware, of someone has a sulotion it would be very welcomed

Update: It seems to be when i stop touching the radio or if I am more than an inch away, the problem arrives. If I am touching the unit, it works properly! So weird. Now I have downgraded to firmware 3.78 and it works fine. Very strange.

This is strange! Definitely contact TBS and get an RMA request. This module is defective, the problem is, many others are experiencing the same issue so it must be a QC problem. They claim it's either bent pins (not always the case), sd card needs to be replaced or improper installation of the chip which does not apply to those with tx16s or similar radios.

These modules are crap, something is up with the internal pin connector on them. I have the same issue and the only way to get it working is to make sure the pins are absolutely straight and once they are and it flashes orange, try not to remove it again unless you absolutely have too. I contacted TBS about this, this is a common problem if you look around forums/reddit.

These modules seem to be having major quality control issues. I have searched the net and there is soooooo many issues with these modules and the crossfire receivers as well. smh. I am having the same exact issue.

Did you ever find a fix for this issue? I have a jumper t16 with a similar issue. Both on crossfire v1 and v2. I can fly if I output the external module to ppm but not through crsf 😔

wtf? contact both tbs and RM

Hmm ya thats weird.. So it was working properly before correct ? Did you try using the TBS AGENT X ? try factory resetting it.. check all setting in your radio also.

Thanks for shooting this video! I got mine fixed with a cranberry juice bottle- it was the exact length of the ac fan hole and perfectly rigid

Note for anybody coming here looking for information on this stabilizer (for Delta Wings only.) Check manual here... radiolink.com.cn/doce/UploadFile/ProductFile/BymeDManual.pdf Things to note about this stab (and the Byme-A for T-tail planes only.) 1...This will work with any Tx/Rx pair that outputs a minimum of 7 channels on S-bus or PPM (the stab will auto-detect which is presented.) However the channel output order must be A, E, T, R, plus channel 5 assigned to a 3-position Mode Switch and channel 7 assigned to a 2 position Motor Arming Switch. If your Tx/Rx normally outputs a different order (eg T, A, E, R for Spectrum) you must be able to remap the outputs to the required A, E, T, R. 2....If you have to remap the channel order the stick positions for "Level Calibration" will probably be different. The ones in the manual are for the Radiolink Tx/Rx combo. If they don't work for your combo you will have to try holding the 8 possible stick positions for 5seconds or so till you find the correct one. (For Mode 2 Tx left stick down and out or down and in with right stich to 1 of the 4 corner positions.) 3....The item 6 (Transmitter Phase Setup) direction to reverse the throttle on the Tx should only pertain to Radiolink and other Txs (like Futaba) that have this quirk. 4....Unlike the Byme-A this only has 3 mode available (5 on the Byme-A.) They are A...Stabilized (self leveling with Pitch and Roll limits) generally called Angle Mode. B...Gyro (no self leveling, no limits just correction of non-stick commanded course deflections by wind etc) generally called Rate Mode. C...Manual (no stabilizer input at all.)

is it compatible with a 6volt sattlite rx?

Hi Stephen, in case anyone who encounters the problem like yours, I'm leaving solution here as well. First, you'll need to make sure all the servo phases are correct and the BymeD calibration can be done by pulling both joysticks to outside corners. Then check if all the surfaces work normally,When it's at Manual Mode(SWC-Down), all surfaces are neutral. When it's at Stabilize Mode(SWC-Up), surfaces move a bit and are able to auto correcting. Last, ff the surfaces don't performe correctly, please press the button on the Byme-D to reverse. Feel free to send mails to after_service@@t if there's any more doubt.

Hi Stephen, as we solved by mails. First, you'll need to make sure all the servo phases are correct and the BymeD calibration can be done by pulling both joysticks to outside corners. Then check if all the surfaces work normally,When it's at Manual Mode(SWC-Down), all surfaces are neutral. When it's at Stabilize Mode(SWC-Up), surfaces move a bit and are able to auto correcting. Last, ff the surfaces don't performe correctly, please press the button on the Byme-D to reverse. Feel free to send mails to after_service@@t if there's any more doubt.

Hi Stephen, as we solved by mails. First, you'll need to make sure all the servo phases are correct and the BymeD calibration can be done by pulling both joysticks to outside corners. Then check if all the surfaces work normally,When it's at Manual Mode(SWC-Down), all surfaces are neutral. When it's at Stabilize Mode(SWC-Up), surfaces move a bit and are able to auto correcting. Last, ff the surfaces don't performe correctly, please press the button on the Byme-D to reverse. Feel free to send mails to after_service@@t if there's any more doubt.

Hi Stephen, as we solved by mails. First, you'll need to make sure all the servo phases are correct and the BymeD calibration can be done by pulling both joysticks to outside corners. Then check if all the surfaces work normally,When it's at Manual Mode(SWC-Down), all surfaces are neutral. When it's at Stabilize Mode(SWC-Up), surfaces move a bit and are able to auto correcting. Last, ff the surfaces don't performe correctly, please press the button on the Byme-D to reverse. Feel free to send mails to [email protected] if there's any more doubt.

I searched KZbin for byme-d because I am having EXACTLY THE SAME PROBLEM. Did you ever get this figured out?

Interesting temporary fix but you're restricting fresh airflow into your cabin. This will cause stale air, fog or frost up inside of windows. Remove fastener, seal hole, move fastener to a new nearby location if you can. Might require drilling a hole but plan location site better than Subaru did! Lol!

I have this problem with my 2010 Outback and have been clearing water out of the same area, front and back everytime it rains. Taking it back to the dealer with this video on my phone. You'd think that Subaru would design a fix and issue a recall for this issue!

What did you end up using to cover the air intake? I used a seed planting tray. Cheers

un petit bout de masking tape de l'autre coté de la canopy pour relier les 2 bords dechirés avant de poser la patch ca aide bcp et ca fait une job plus net.Et pas de sable qui se colle par la suite dans l'espace vide ;)