@tilliethompson6681 - I am not sure if it works with another brand valve. I have only used the repair kit with old Brasscraft angle and straight multi-turn valves.

Glad you liked it.

@jakec5618 - The plastic kit should work without any issues. I have never had any problems. Make sure you don't overtighten the bonnet nut. The bonnet nut only needs to be tight enough to prevent it from leaking. Otherwise, it will be tough to turn if overtighten. Also, clean the inside of the shutoff valve properly if old rubber pieces do not come out. I think Brasscraft also makes metal kits, but plastic should work fine.

@@BajraDIY I see appreciate it. Also, have you ever had any issues where the new stem kit doesn't work due to a bad seat ?

Thanks for the exact specification.

@DanielGonzalez-tu6dh - It's a Dremmel multi-max oscillating tool from Home Depot. You can use any inexpensive orbital or oscillating tool to remove dust from the car carpet. However, multi-tools are suitable for other home maintenance projects. It has many uses. Amazon link - amzn.to/478tlzB

@@BajraDIY appreciate it thank you !

Glad you liked the video! Thanks for the torque spec.

@murielleetjean-pierre6249 - Glad it was helpful!

@cmflow69200 - The stem repair kit information is in the description. I was only able to find it at Home Depot. Local hardware stores may also carry it.

@@BajraDIY thank you so much

@ninjaman12375 - Thanks for the tip! I will try snow foam.

Thanks for the tip!

Glad to help

I have successfully fixed many valves using this method without any issues. However, I have encountered challenges when removing the old valve parts. 1. In the video, I have the toilet supply line (braided line) disconnected because I was also replacing the toilet. Removing the toilet line was particularly difficult, and I was concerned that the CPVC pipe sticking out of the wall might break. Replacing the bonnet nut and stem was easy, but it's crucial not to put too much strain on the CPVC pipe at any given time. If you have a copper line, you're in better shape. Just use new stem with washer and new washer for the bonnet nut, as shown in the video. Use two wrenches, one to hold the body and the other to loosen or tighten the bonnet nut. 2. In another project, the old plastic stem (original valve, 20 years old) on the hot water line was almost chewed up, possibly due to chemical reactions in the hot water line. Removing it was tricky since it nearly broke when turning. 3. I also encountered a situation where the shut-off valve handle would not turn at all. It was stuck, and at that time, the only option was to replace the shut-off valve. I ended up calling a plumber. This was before I had any DIY skills. :-) All of my challenges were encountered when removing the old parts. If you're able to remove the old stems and valves, installing new parts is easy as long as you follow the directions. But please seek professional help and hire a plumber if you have any doubts. Also, make sure that your main water shut-off valve is working properly before starting any plumbing projects.

I never had to remove the lock clip. When removing the oil filter canister, the rim of the wrench tool slightly lifts the clip. Never had any issues.

Where can I get that tool online?

@DenverBlackman - Amazon link is amzn.to/3An4E6d. You can also check the MotivX site www.motivxtools.com/.

Why should we avoid this unless people want to avoid a momentary vinegar aroma :-)? I have seen HVAC technicians come for a yearly check-up and do the same thing (vinegar or Clorox bleach), clean coil fins, and check compressor capacitor capacitance and charge anywhere from $80-$100. What's wrong with this DIY preventive maintenance?

Yes, let your drain clog up, and your air-conditioning go off. The code that’s going to flash will probably be 196. 🤡

Why do you say not to do it? Do you even know, or do you just say stuff?

Glad it helped!

A new valve, particularly a quarter-turn valve, generally has a longer lifespan than a multi-turn valve. However, replacing the rubber washer in a multi-turn valve is a simple task that any average DIYer like myself can complete within minutes. Most of the time, other parts of the valve are still in good shape even after 20-30 years, and just a washer fix can extend the operability of the multi-turn valve by another 7-10 years. On the other hand, replacing the entire valve is a more complex process that involves removing the compression nut and ferrule and cleaning the pipe for the new ferrule and shutoff valve. Depending on the situation, access to more tools will be required, and a professional plumber may be needed.

​You also might have a house where the valve is soldered on to the copper pipe. This is not a bad option based on skills and risk.

And in his case with old CPVC pipe sticking out of the wall it could easily break or leak if the whole valve is replaced as opposed to just repairing it.

@@everythinghomerepair1747 And another good reason to repair the guts is that you bought a craftsmaster repair kit and then find out there was a popular brand 30 years ago named Watts all over "YOUR OLD HOUSE" and the parts crumbled in your hands, but the craftsmaster thin plastic gasket can be sliced gently and put on the watts. Make some teflon tape rope, wrap it real good and assemble. Go back to installing sink faucet. Congratulate myself for not trying both at once but at least the repair video helped save the day and the original request for the sink leak has been fixed and you can go home. To be continued... Is "WATTS" still around (lol)

It's faster and less involved than having to sweat an extension to a very short stub for a replacement valve.